 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| slos218f ? december 1998 ? revised january 2005 1 www.ti.com post office box 1443 ? houston, texas 77251?1443 supply current ...23 a/channel gain-bandwidth product . . . 220 khz output drive capability . . . 10 ma input offset voltage ...20 v (typ) v dd range . . . 2.7 v to 6 v power supply rejection ratio . . . 106 db ultralow-power shutdown mode i dd . . . 16 na/ch rail-to-rail input/output (rrio) ultrasmall packaging ? 5 or 6 pin sot-23 (tlv2450/1) ? 8 or 10 pin msop (tlv2452/3) description the tlv245x is a family of rail-to-rail input/output operational amplifiers that sets a new performance point for supply current and ac performance. these devices consume a mere 23 a/channel while offering 220 khz of gain-bandwidth product, much higher than competitive devices with similar supply current levels. along with increased ac performance, the amplifier provides high output drive capability, solving a major shortcoming of older micropower rail-to-rail input/output operational amplifiers. the tlv245x can swing to within 250 mv of each supply rail while driving a 2.5-ma load. both the inputs and outputs swing rail-to-rail for increased dynamic range in low-voltage applications. this performance makes the tlv245x family ideal for portable medical equipment, patient monitoring systems, and data acquisition circuits. family package table device number of package types shutdown universal device number of channels pdip soic sot-23 tssop msop shutdown universal evm board tlv2450 1 8 8 6 ? ? yes tlv2451 1 8 8 5 ? ? ? refer to the evm tlv2452 2 8 8 ? ? 8 ? refer to the evm selection guide tlv2453 2 14 14 ? ? 10 yes selection guide (lit# slou060) tlv2454 4 14 14 ? 14 ? ? (lit# slou060) tlv2455 4 16 16 ? 16 ? yes a selection of single-supply operational amplifier products ? device v dd (v) bw (mhz) slew rate (v/ s) i dd (per channel) ( a) rail-to-rail tlv245x 2.7 ? 6.0 0.22 0.11 23 i/o tlv247x 2.7 ? 6.0 2.8 1.5 600 i/o tlv246x 2.7 ? 6.0 6.4 1.6 550 i/o tlv277x 2.5 ? 6.0 5.1 10.5 1000 o ? all specifications measured at 5 v. please be aware that an important notice concerning avail ability, standard warranty, and use in critical applications o f texas instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. copyright ? 1998?2005, t exas instruments incorporated operational amplifier ? + all trademarks are the property of their respective owners.
slos218f ? december 1998 ? revised january 2005 2 www.ti.com post office box 1443 ? houston, texas 77251?1443 description (continued) three members of the family (tlv2450/3/5) offer a shutdown terminal for conserving battery life in portable applications. during shutdown, the outputs are placed in a high-impedance state and the amplifier consumes only 16 na/channel. the family is fully specified at 3 v and 5 v across an expanded industrial temperature range (?40 c to 125 c). the singles and duals are available in the sot23 and msop packages, while the quads are available in tssop. the tlv2450 offers an amplifier with shutdown functionality all in a 6-pin sot23 package, making it perfect for high density circuits. tlv2450 and tlv2451 available options packaged devices t a small outline ? sot-23 plastic dip t a small outline (d) ? (dbv) symbol plastic dip (p) 0 c to 70 c tlv2450cd tlv2451cd tlv2450cdbv tlv2451cdbv vaqc varc tlv2450cp tlv2451cp ?40 c to 125 c tlv2450id tlv2451id tlv2450idbv tlv2451idbv vaqi vari tlv2450ip tlv2451ip ?40 c to 125 c tlv2450aid tlv2451aid ? ? ? ? tlv2450aip tlv2451aip ? this package is available taped and reeled. to order this packaging option, add an r suffix to the part number (e.g., tlv2450cdr). tlv2452 and tlv2453 available options packaged devices t a small outline msop plastic dip plastic dip t a outline (d) ? (dgk) ? symbol ? (dgs) ? symbol ? dip (n) dip (p) 0 c to 70 c tlv2452cd tlv2453cd tlv2452cdgk ? xxtiabi ? ? tlv2453cdgs ? xxtiabk ? tlv2453cn tlv2452cp ? ?40 c to 125 c tlv2452id tlv2453id tlv2452idgk ? xxtiabj ? ? tlv2453idgs ? xxtiabl ? tlv2453in tlv2452ip ? ?40 c to 125 c tlv2452aid tlv2453aid ? ? ? ? ? ? ? ? ? tlv2453ain tlv2452aip ? ? this package is available taped and reeled. to order this packaging option, add an r suffix to the part number (e.g., tlv2452cd r). ? xx represents the device date code. tlv2454 and tlv2455 available options packaged devices t a small outline (d) ? plastic dip (n) tssop (pw) ? 0 c to 70 c tlv2454cd tlv2455cd tlv2454cn tlv2455cn tlv2454cpw tlv2455cpw ?40 c to 125 c tlv2454id tlv2455id tlv2454in tlv2455in tlv2454ipw tlv2455ipw ?40 c to 125 c tlv2454aid tlv2455aid tlv2454ain tlv2455ain tlv2454aipw tlv2455aipw ? this package is available taped and reeled. to order this packaging option, add an r suffix to the part number (e.g., tlv2454cdr). note : for the most current package and ordering information, see the package option addendum located at the end of this data sheet, or refer to our web site at www.ti.com. slos218f ? december 1998 ? revised january 2005 3 www.ti.com post office box 1443 ? houston, texas 77251?1443 tlv245x package pinouts (1) 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 1out 1in ? 1in+ v dd + 2in+ 2in ? 2out 1/2shdn 4out 4in ? 4in+ gnd 3in + 3in? 3out 3/4shdn (top view) tlv2455 d, n, or pw package 3 2 4 5 (top view) 1 out gnd in+ v dd+ in ? 1 2 3 4 5 6 7 14 13 12 11 10 9 8 1out 1in ? 1in+ gnd nc 1shdn nc v dd + 2out 2in ? 2in+ nc 2shdn nc (top view) tlv2451 dbv package 3 2 4 6 (top view) 1 out gnd in+ v dd+ in ? tlv2450 dbv package 5 shdn 1 2 3 4 8 7 6 5 nc in ? in + gnd shdn v dd + out nc tlv2450 d or p package (top view) 1 2 3 4 8 7 6 5 nc in ? in + gnd nc v dd + out nc tlv2451 d or p package (top view) 1 2 3 4 8 7 6 5 1out 1in ? 1in + gnd v dd + 2out 2in ? 2in+ tlv2452 d, dgk, or p package (top view) tlv2453 d or n package 1 2 3 4 5 6 7 14 13 12 11 10 9 8 1out 1in ? 1in+ v dd + 2in+ 2in ? 2out 4out 4in ? 4in+ gnd 3in+ 3in ? 3out (top view) tlv2454 d, n, or pw package nc ? no internal connection (1) sot?23 may or may not be indicated 1 2 3 4 5 10 9 8 7 6 1out 1in ? 1in+ gnd 1shdn v dd + 2out 2in ? 2in+ 2shdn tlv2453 dgs package (top view) typical pin 1 indicators printed or molded dot bevel edges pin 1 molded ?u? shape pin 1 stripe pin 1 pin 1 slos218f ? december 1998 ? revised january 2005 4 www.ti.com post office box 1443 ? houston, texas 77251?1443 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) ? supply voltage, v dd (see note 1) 7 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . differential input voltage, v id v dd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . continuous total power dissipation see dissipation rating table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . operating free-air temperature range, t a : c suffix 0 c to 70 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i suffix ?40 c to 125 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . maximum junction temperature, t j 150 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . storage temperature range, t stg ?65 c to 150 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ? stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. these are stress ratings only, a nd functional operation of the device at these or any other conditions beyond those indicated under ?recommended operating conditi ons? is not implied. exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. note : all voltage values, except differential voltages, are with respect to gnd. dissipation rating table package jc ( c/w) ja ( c/w) t a 25 c power rating d (8) 38.3 176 710 mw d (14) 26.9 122.3 1022 mw d (16) 25.7 114.7 1090 mw dbv (5) 55 324.1 385 mw dbv (6) 55 294.3 425 mw dgk (8) 54.2 259.9 481 mw dgs (10) 54.1 257.7 485 mw n (14, 16) 32 78 1600 mw p (8) 41 104 1200 mw pw (14) 29.3 173.6 720 mw pw (16) 28.7 161.4 774 mw recommended operating conditions min max unit supply voltage, v dd single supply 2.7 6 v supply voltage, v dd split supply 1.35 3 v common-mode input voltage range, v icr 0 v dd v operating free-air temperature, t a c-suffix 0 70 c operating free-air temperature, t a i-suffix ?40 125 c v ih 2 v shutdown on/off voltage level ? v il v dd = 5v 0.8 v shutdown on/off voltage level v il v dd = 3v 0.5 v ? relative to voltage on the gnd terminal of the device. slos218f ? december 1998 ? revised january 2005 5 www.ti.com post office box 1443 ? houston, texas 77251?1443 electrical characteristics at specified free-air temperature, v dd = 3 v (unless otherwise noted) parameter test conditions t a ? min typ max unit tlv245x 25 c 300 1500 v io input offset voltage tlv245x full range 2000 v v io input offset voltage tlv245xa 25 c 300 1000 v tlv245xa full range 1300 vio temperature coefficient of input v dd = 1.5 v v o = 0, 0.3 v/ c vio temperature coefficient of input offset voltage v dd = 1.5 v v ic = 0, v o = 0, r s = 50 ? 0.3 v/ c i io input offset current v ic = 0, r s = 50 25 c 0.3 4.5 na i io input offset current full range 5.5 na i ib input bias current 25 c 0.9 5 na i ib input bias current full range 7 na v oh high-level output voltage v ic = 1.5 v, i oh = ? 500 a 25 c 2.85 2.95 v v oh high-level output voltage v ic = 1.5 v, i oh = ? 500 a full range 2.83 v v ol low-level output voltage v ic = 1.5 v, i ol = 500 a 25 c 0.09 0.16 v v ol low-level output voltage v ic = 1.5 v, i ol = 500 a full range 0.2 v sourcing 25 c 4 12 i os short-circuit output current sourcing full range 3 ma i os short-circuit output current sinking 25 c 2 7 ma sinking full range 1 i o output current v o = 0.5 v from rail 25 c 4 ma a vd large-signal differential voltage v o(pp) = 1 v, r l = 10 k ? c 96 110 db a vd large-signal differential voltage amplification v o(pp) = 1 v, r l = 10 k ? full range 91 db r i(d) differential input resistance 25 c 10 9 ? c ic common-mode input capacitance f = 10 khz 25 c 4.5 pf z o closed-loop output impedance f = 10 khz, a v = 10 25 c 80 ? cmrr common-mode rejection ratio v ic = 0 to 3 v, 25 c 70 80 db cmrr common-mode rejection ratio v ic = 0 to 3 v, r s = 50 ? tlv245xc full range 66 db v dd = 2.7 v to 6 v, v ic = v dd /2, 25 c 76 89 k svr supply voltage rejection ratio v dd = 2.7 v to 6 v, no load v ic = v dd /2, full range 74 db k svr supply voltage rejection ratio ( ? v dd / ? v io ) v dd = 3 v to 5 v, v ic = v dd /2, 25 c 88 106 db ( v dd / v io ) v dd = 3 v to 5 v, no load v ic = v dd /2, full range 84 25 c 23 35 i dd supply current (per channel) v o = 1.5 v, no load tlv245xc full range 40 a i dd supply current (per channel) v o = 1.5 v, no load tlv245xi full range 45 a supply current in shutdown 25 c 12 65 i dd(shdn) supply current in shutdown mode (tlv2450, tlv2453, tlv2455) (per channel) shdn = ?v dd tlv245xc full range 70 na i dd(shdn) mode (tlv2450, tlv2453, tlv2455) (per channel) shdn = ?v dd tlv245xi full range 80 na ? full range is 0 c to 70 c for c suffix and ? 40 c to 125 c for i suffix. slos218f ? december 1998 ? revised january 2005 6 www.ti.com post office box 1443 ? houston, texas 77251?1443 operating characteristics at specified free-air temperature, v dd = 3 v (unless otherwise noted) parameter test conditions t a ? min typ max unit sr slew rate at unity gain v o(pp) = 0.8 v, c l = 150 pf, 25 c 0.05 0.11 v/ s sr slew rate at unity gain v o(pp) = 0.8 v, r l = 10 k ? c l = 150 pf, full range 0.02 v/ s v n equivalent input noise voltage f = 100 hz 25 c 49 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 51 nv/ hz i n equivalent input noise current f = 1 khz 25 c 3.5 pa / hz v o(pp) = 1.5 v, a v = 1 0.04% thd + n total harmonic distortion plus noise v o(pp) = 1.5 v, r l = 10 k ? , f = 1 khz a v = 10 25 c 0.3% thd + n total harmonic distortion plus noise r l = 10 k ? , f = 1 khz a v = 100 25 c 1.5% t (on) amplifier turnon time a v = 5, r l = open, 25 c 59 s t (off) amplifier turnoff time a v = 5, r l = open, measured at 50% point 25 c 836 ns gain-bandwidth product f = 10 khz, r l = 10 k ? 25 c 200 khz v (step)pp = 2 v, a v = ?1, 0.1% 26 t s settling time a v = ?1, c l = 10 pf, r l = 10 k ? 0.01% 25 c 31 s t s settling time v (step)pp = 2 v, a v = ?1, 0.1% 25 c 26 s a v = ?1, c l = 56 pf, r l = 10 k ? 0.01% 31 m phase margin r l = 10 k ? , c l = 1000 pf 25 c 56 gain margin r l = 10 k ? , c l = 1000 pf 25 c 7 db ? full range is 0 c to 70 c for c suffix and ? 40 c to 125 c for i suffix. slos218f ? december 1998 ? revised january 2005 7 www.ti.com post office box 1443 ? houston, texas 77251?1443 electrical characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? min typ max unit tlv245x 25 c 300 1500 v io input offset voltage tlv245x full range 2000 v v io input offset voltage tlv245xa 25 c 300 1000 v tlv245xa full range 1300 vio temperature coefficient of input v dd = 2.5 v v o = 0, 0.3 v/ c vio temperature coefficient of input offset voltage v dd = 2.5 v v ic = 0, v o = 0, r s = 50 ? 0.3 v/ c i io input offset current v ic = 0, r s = 50 25 c 0.3 4.5 na i io input offset current full range 5.5 na i ib input bias current 25 c 0.5 5 na i ib input bias current full range 7 na v oh high-level output voltage v ic = 2.5 v, i oh = ? 500 a 25 c 4.87 4.97 v v oh high-level output voltage v ic = 2.5 v, i oh = ? 500 a full range 4.85 v v ol low-level output voltage v ic = 2.5 v, i ol = 500 a 25 c 0.07 0.15 v v ol low-level output voltage v ic = 2.5 v, i ol = 500 a full range 0.16 v sourcing 25 c 20 32 i os short-circuit output current sourcing full range 18 ma i os short-circuit output current sinking 25 c 12 18 ma sinking full range 10 i o output current v o = 0.5 v from rail 25 c 10 ma a vd large-signal differential voltage v o(pp) = 3 v, r l = 10 k ? c 96 103 db a vd large-signal differential voltage amplification v o(pp) = 3 v, r l = 10 k ? full range 91 db r i(d) differential input resistance 25 c 10 9 ? c ic common-mode input capacitance f = 10 khz 25 c 4.5 pf z o closed-loop output impedance f = 10 khz, a v = 10 25 c 45 ? cmrr common-mode rejection ratio v ic = 0 to 5 v, 25 c 70 80 db cmrr common-mode rejection ratio v ic = 0 to 5 v, r s = 50 ? tlv245xc full range 68 db v dd = 2.7 v to 6 v, v ic = v dd /2, 25 c 76 89 k svr supply voltage rejection ratio v dd = 2.7 v to 6 v, no load v ic = v dd /2, full range 74 db k svr supply voltage rejection ratio ( ? v dd / ? v io ) v dd = 3 v to 5 v, v ic = v dd /2, 25 c 88 106 db ( v dd / v io ) v dd = 3 v to 5 v, no load v ic = v dd /2, full range 84 25 c 23 42 i dd supply current (per channel) v o = 2.5 v, no load tlv245xc full range 44 a i dd supply current (per channel) v o = 2.5 v, no load tlv245xi full range 46 a supply current in shutdown mode 25 c 16 70 i dd(shdn) supply current in shutdown mode (tlv2450, tlv2453, tlv2455) (per channel) shdn = ?v dd tlv245xc full range 70 na i dd(shdn) (tlv2450, tlv2453, tlv2455) (per channel) shdn = ?v dd tlv245xi full range 80 na ? full range is 0 c to 70 c for c suffix and ? 40 c to 125 c for i suffix. slos218f ? december 1998 ? revised january 2005 8 www.ti.com post office box 1443 ? houston, texas 77251?1443 operating characteristics at specified free-air temperature, v dd = 5 v (unless otherwise noted) parameter test conditions t a ? min typ max unit sr slew rate at unity gain v o(pp) = 2 v, c l = 150 pf, 25 c 0.05 0.11 v/ s sr slew rate at unity gain v o(pp) = 2 v, r l = 10 k ? c l = 150 pf, full range 0.02 v/ s v n equivalent input noise voltage f = 100 hz 25 c 49 nv/ hz v n equivalent input noise voltage f = 1 khz 25 c 52 nv/ hz i n equivalent input noise current f = 1 khz 25 c 3.5 pa / hz v o(pp) = 3 v, a v = 1 0.02% thd + n total harmonic distortion plus noise v o(pp) = 3 v, r l = 10 k ? , f = 1 khz a v = 10 25 c 0.18% thd + n total harmonic distortion plus noise r l = 10 k ? , f = 1 khz a v = 100 25 c 0.9% t (on) amplifier turnon time a v = 5, r l = open, 25 c 59 s t (off) amplifier turnoff time a v = 5, r l = open, measured at 50% point 25 c 836 ns gain-bandwidth product f = 10 khz, r l = 10 k ? 25 c 220 khz v (step)pp = 2 v, a v = ?1, 0.1% 24 t s settling time a v = ?1, c l = 10 pf, r l = 10 k ? 0.01% 25 c 30 s t s settling time v (step)pp = 2 v, a v = ?1, 0.1% 25 c 25 s a v = ?1, c l = 56 pf, r l = 10 k ? 0.01% 30 m phase margin r l = 10 k ? , c l = 1000 pf 25 c 56 gain margin r l = 10 k ? , c l = 1000 pf 25 c 7 db ? full range is 0 c to 70 c for c suffix and ? 40 c to 125 c for i suffix. slos218f ? december 1998 ? revised january 2005 9 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics table of graphs figure v io input offset voltage vs common-mode input voltage 1, 2 i io input offset current vs common-mode input voltage vs free-air temperature 3, 4 7, 8 i ib input bias current vs common-mode input voltage vs free-air temperature 5, 6 7, 8 a vd differential voltage amplification vs frequency 9, 10 phase vs frequency 9, 10 v ol low-level output voltage vs low-level output current 11, 13 v oh high-level output voltage vs high-level output current 12, 14 z o output impedance vs frequency 15, 16 cmrr common-mode rejection ratio vs frequency 17 psrr power supply rejection ratio vs frequency 18 i dd supply current vs supply voltage 19 i dd supply current vs free-air temperature 20 v n equivalent input noise voltage vs frequency 21 thd + n total harmonic distortion plus noise vs frequency 22, 23 m phase margin vs load capacitance 24 gain-bandwidth product vs supply voltage 25 sr slew rate vs supply voltage 26 sr slew rate vs supply voltage vs free-air temperature 26 27 v o(pp) maximum peak-to-peak output voltage vs frequency 28 crosstalk vs frequency 29, 30 small-signal follower pulse response vs time 31, 33 large-signal follower pulse response vs time 32, 34 shutdown on supply current vs time 35 shutdown off supply current vs time 36 shutdown supply current vs free-air temperature 37 shutdown supply current vs time 38 ? 41 shutdown pulse vs time 38 ? 41 shutdown off pulse response vs time 42, 43 shutdown on pulse response vs time 44, 45 shutdown reverse isolation vs frequency 46 shutdown forward isolation vs frequency 47 slos218f ? december 1998 ? revised january 2005 10 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 1 50 0 ?100 ?150 ?200 ?50 0 0.5 1 1.5 2 2.5 3 150 100 200 input offset voltage vs common-mode input voltage v ic ? common-mode input voltage ? v ? input offset voltage ? v io v v dd =3 v t a = 25 c ?0.5 3.5 figure 2 0 ?20 ?60 ?80 ?100 80 ?40 0 0.5 1 1.5 2 2.5 3 40 20 60 100 3.5 4 input offset voltage vs common-mode input voltage v ic ? common-mode input voltage ? v 4.5 5 v dd =5 v t a = 25 c ? input offset voltage ? v io v ?0.5 5.5 figure 3 0 input offset current vs common-mode input voltage v ic ? common-mode input voltage ? v 0.5 1 1.5 ? input offset current ? pa io i 0 0.5 1 ?60 ?40 20 60 ?20 40 0 v dd = 3 v t a = 25 c figure 4 ?60 0 ?50 input offset current vs common-mode input voltage 20 5 v ic ? common-mode input voltage ? v ?20 0 10 ?40 0.5 1 1.5 ? input offset current ? pa ?10 ?30 2 2.5 3 3.5 4 io i v dd = 5 v t a = 25 c 4.5 slos218f ? december 1998 ? revised january 2005 11 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 5 v ic ? common-mode input voltage ? v 0 ?1 ?3 ?4 0 0.5 1 1.5 ? input bias current ? na 2 3 2 2.5 3 1 ?2 i ib input bias current vs common-mode input voltage ?0.5 3.5 v dd = 3 v t a = 25 c figure 6 1 0 ?2 ?3 ?4 ?1 0 0.5 1 1.5 2 2.5 3 3 2 3.5 4 input bias current vs common-mode input voltage v ic ? common-mode input voltage ? v 4.5 5 ? input bias current ? na i ib 5.5 ?0.5 v dd =5 v t a = 25 c figure 7 / i io ? input bias and input offset currents ? na i ib 0.5 0.4 0.3 0.2 0.1 0.8 ?55 ?35 ?15 5 25 45 0.7 0.6 0.9 t a ? free-air temperature ? c input offset current and input bias current vs free-air temperature 65 85 105 125 0 ?0.1 v dd = 3 v i ib i io 1.1 1 1.4 1.3 1.2 1.5 figure 8 / i io ? input bias and input offset currents ? na i ib 0.5 0.4 0.3 0.2 0.1 0.8 ?55 ?35 ?15 5 25 45 0.7 0.6 0.9 t a ? free-air temperature ? c input offset current and input bias current vs free-air temperature v dd = 5 v i ib i io 65 85 105 125 0 ?0.1 slos218f ? december 1998 ? revised january 2005 12 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics 1k 10k 100k 1m ?60 differential voltage amplification and phase vs frequency 120 f ? frequency ? hz 0 60 90 30 ?30 100 v dd = 3 v t a = 25 c phase gain ? differential voltage amplification ? db a vd phase ? 120 60 0 ?60 ?120 ?180 figure 9 1k 10k 100k 1m ?60 differential voltage amplification and phase vs frequency 120 f ? frequency ? hz 0 60 90 30 ?30 100 v dd = 5 v dc t a = 25 c phase gain ? differential voltage amplification ? db a vd phase ? 120 60 0 ?60 ?120 ?180 figure 10 slos218f ? december 1998 ? revised january 2005 13 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 11 i ol ? low-level output current ? ma t a = ?40 c t a = 25 c t a = 85 c t a = 125 c 1.5 1 0.5 0 0123456 ? low-level output voltage ? v 2 2.5 3 78910 v ol low-level output voltage vs low-level output current v dd = 3 v figure 12 i oh ? high-level output current ? ma 1.5 1 0.5 0 0 2.5 5 7.5 ? high-level output voltage ? v 2 2.5 3 10 12.5 15 v oh t a = 125 c t a = 85 c t a = 25 c t a = ?40 c high-level output voltage vs high-level output current v dd = 3 v figure 13 2.5 2 1 0.5 0 1.5 3 0 5 10 15 20 25 v dd = 5 v t a = ?40 c t a = 125 c t a = 25 c low-level output voltage vs low-level output current ol v ? low-level output voltage ? v i ol ? low-level output current ? ma t a = 85 c 3.5 4 4.5 5 figure 14 2.5 2 1 0.5 0 4.5 1.5 3.5 3 4 5 0 5 10 15 20 25 30 35 40 v dd = 5 v high-level output voltage vs high-level output current t a = ?40 c t a = 125 c t a = 25 c i oh ? high-level output current ? ma v oh ? high-level output voltage ? v t a = 85 c slos218f ? december 1998 ? revised january 2005 14 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 15 f ? frequency ? hz 10k 1k 100 10 1 100 1k 10k 100k 1m ? output impedance ? z o ? output impedance vs frequency a v = 10 a v = 1 a v = 100 v dd = 3 v t a = 25 c figure 16 output impedance vs frequency f ? frequency ? hz 10k 1k 100 10 1 0.1 100 1k 10k 100k 1m ? output impedance ? z o ? a v = 10 a v = 1 a v = 100 v dd = 5 v t a = 25 c common-mode rejection ratio vs frequency f ? frequency ? hz 10 1k 10k 100k 1m cmrr ? common-mode rejection ratio ? db v dd = 3 v or 5 v t a = 25 c 100 80 60 40 20 0 120 100 figure 17 slos218f ? december 1998 ? revised january 2005 15 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 18 power supply rejection ratio vs frequency f ? frequency ? hz 10 1k 10k 100k 1m psrr ? power supply rejection ratio ? db 100 90 80 70 60 40 30 20 10 0 50 v dd = 3 v or 5 v t a = 25 c psrr + psrr ? 100 figure 19 20 15 5 0 2.5 3 3.5 4 ? supply current ? 25 35 40 4.5 5 5.5 30 10 t a = 125 c t a = 85 c t a = 25 c t a = ?40 c v dd ? supply voltage ? v i dd a supply current vs supply voltage a v = 1 shdn = v dd per channel figure 20 5 0 25 ?55 ?35 15 10 20 30 ?15 5 supply current vs free-air temperature t a ? free-air temperature ? c 25 45 v i = v dd /2 shdn = v dd per channel 65 v dd = 3 v dd i supply current ? ?a v dd = 5 v 85 105 125 figure 21 100 1k 10k 1 equivalent input noise voltage vs frequency 100 f ? frequency ? hz 10 10 nv/ hz ? equivalent input noise voltage ? v n 100k v dd = 3 v or 5 v t a = 25 c slos218f ? december 1998 ? revised january 2005 16 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 22 0.1% 0.01% 0.001% 10 100 1k 1% 10% f ? frequency ? mhz 100% 10k 100k a v = 100 a v = 10 a v = 1 total harmonic distortion plus noise vs frequency thd+n ? total harmonic distortion + noise v dd = 3 v v o(pp) = 1.5 v r l = 10 k ? t a = 25 c figure 23 total harmonic distortion plus noise vs frequency 10% 1% 0.1% 0.010% 0.001% 100% thd+n ? total harmonic distortion + noise 10 100 1k 10k 100k f ? frequency ? hz v dd = 5 v v o(pp) = 3 v r l = 10 k ? t a = 25 c a v = 1 a v = 10 a v = 100 figure 24 phase margin vs load capacitance c l ? load capacitance ? pf v dd = 5 v r l = 10 k ? t a = 25 c 100 90 80 70 60 40 30 20 10 0 50 100 1k 10k 100k m ? phase margin r null = 500 ? r null = 200 ? r null = 100 ? r null = 50 ? r null = 10 ? r null = 0 ? figure 25 gain-bandwidth product ? khz 2.5 3 3.5 4 4.5 v dd ? supply voltage ? v 5 gain-bandwidth product vs supply voltage 5.5 240 230 220 210 200 270 260 250 280 190 180 f = 1 khz r l = 10 k ? t a = 25 c slos218f ? december 1998 ? revised january 2005 17 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 26 0.1 0.09 2.5 3 3.5 4 sr ? slew rate ? 0.11 0.12 4.5 5 v dd ? supply voltage ? v s v/ f = 10 khz t a = 25 c r l = 10 k ? c l = 160 pf a v = 1 slew rate vs supply voltage figure 27 0.1 0.08 0.06 ?40 ?20 0 20 40 60 80 sr ? slew rate ? 0.12 0.14 0.16 100 120 t a ? free-air temperature ? c s v/ v dd = 5 v v dd = 3 v f = 10 khz r l = 10 k ? c l = 160 pf a v = 1 140 slew rate vs free-air temperature maximum peak-to-peak output voltage vs frequency f ? frequency ? hz 100 1k 10k 100k v o(pp) = 5 v 5 4.5 4 3.5 3 2 1.5 1 0.5 2.5 thd + n < 5% a v = 5 r l = 20 k ? t a = 25 c ? maximum peak-to-peak output voltage ? v v o(pp) v o(pp) = 3 v 0 figure 28 slos218f ? december 1998 ? revised january 2005 18 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 29 ?60 ?80 ?90 ?110 10 100 1k crosstalk ? db ?40 ?30 f ? frequency ? hz ?20 10k 100k ?50 ?70 ?100 v dd = 3 v a v = 1 r l = 10 k ? all channels crosstalk vs frequency figure 30 ?60 ?80 ?90 ?110 10 100 1k crosstalk ? db ?40 ?30 f ? frequency ? hz ?20 10k 100k ?50 ?70 ?100 v dd = 5 v a v = 1 r l = 10 k ? all channels crosstalk vs frequency t ? time ? s 0.1 0.05 0 ?0.1 ?2 0 2 4 6 8 10 ? output voltage ? v 0.2 0.25 0.3 12 14 16 0.15 ?0.05 0.15 0.1 0.05 0 ?0.05 ?0.1 ?0.15 ?0.2 ?0.25 ?0.3 ?0.35 ?0.4 v o ? input voltage ? v v i v i v o v dd = 3 v r l = 10 k ? c l = 160 pf a v = 1 t a = 25 c f = 45 khz small-signal follower pulse response vs time figure 31 slos218f ? december 1998 ? revised january 2005 19 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics 1 0 ?1 ?2 4 ?20 0 20 40 3 2 5 60 t ? time ? s 80 large-signal follower pulse response vs time v dd = 3 v a v = 1 r l = 10 k ? c l = 160 pf f = 10 khz t a = 25 c ?2 ?3 ?4 ?5 1 0 ?1 2 ? output voltage ? v v o v i ? input voltage ? v v i v o 100 figure 32 80 40 0 ?40 ?80 200 ?5 0 5 10 15 20 160 120 240 t ? time ? s small-signal follower pulse response vs time v dd = 5 v a v = 1 r l = 10 k ? c l = 160 pf t a = 25 c ?80 ?120 ?160 ?200 ?240 40 0 ?40 80 ? output voltage ? mv v o v i ? input voltage ? mv v i v o figure 33 slos218f ? december 1998 ? revised january 2005 20 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics t ? time ? s 4 2 0 ?4 ?10 0 10 20 30 40 50 ? output voltage ? v 6 8 10 60 70 100 ?2 2 1 0 ?1 ?4 ?5 ?7 ?8 ?10 v o ? input voltage ? v v i v i v o v dd = 5 v r l = 10 k ? c l = 160 pf a v = 1 t a = 25 c f = 10 khz 80 90 ?2 ?3 ?6 ?9 large-signal follower pulse response vs time figure 34 ?20 ?4 0 shutdown on supply current vs time 180 10 t ? time ? s 100 140 160 20 40 60 ?2 0 2 shutdown control signal dd i supply current ? ?a shutdown pulse ? v 120 80 10 5 0 ?5 ?10 ?15 ?20 ?25 ?30 ?35 ?40 468 supply current ? i dd figure 35 slos218f ? december 1998 ? revised january 2005 21 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics ?10 ?20 shutdown off supply current vs time 50 80 t ? time ? s 10 30 40 ?10 0 20 dd i supply current ? ?a shutdown pulse ? v 20 0 10 5 0 ?5 ?10 ?15 ?20 40 60 70 10 30 50 shutdown control signal supply current ? i dd figure 36 0.8 0.4 0.2 0 ?55 ?35 ?15 5 25 45 65 ? supply current ? 1 1.4 shutdown supply current vs free-air temperature 1.6 85 105 125 1.2 0.6 i dd a t a ? free-air temperature ? c v dd = 3 v shutdown mode a v = 1 r l = open v i = v dd /2 v v dd = 5 v figure 37 slos218f ? december 1998 ? revised january 2005 22 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics 0 ?5 ?3 ?1 1 3 5 7 shutdown supply current and shutdown pulse vs time 9111315 3 4 5 2 1 0 t ? time ? s ? shutdown supply current ? shutdown pulse ? v i dd(sd) a i dd(sd) v dd = 3 v a v = 1 v i = 1.5 v r l = 10 k ? c l = 160 pf and 10 pf t a = 25 c 5 10 15 20 25 sd pulse 30 figure 38 5 ?100 ?50 0 50 shutdown supply current and shutdown pulse vs time 100 150 200 2 3 4 5 1 0 t ? time ? s ? shutdown supply current ? shutdown pulse ? v i dd(sd) a sd pulse i dd(sd) v dd = 3 v a v = 1 v i = 1.5 v r l = 10 k ? c l = 160 pf and 10 pf t a = 25 c 0 10 15 20 25 30 figure 39 slos218f ? december 1998 ? revised january 2005 23 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics ?100 ?50 0 50 ? shutdown supply current ? shutdown supply current and shutdown pulse vs time 100 150 200 0 3 4 5 2 1 0 shutdown pulse ? v t ? time ? s i dd(sd) a v dd = 5 v a v = 1 v i = 2.5 v r l = 10 k ? c l = 160 pf and 10 pf t a = 25 c sd pulse i dd(sd) 5 10 15 20 25 figure 40 ?10 ?5 0 5 shutdown supply current and shutdown pulse vs time 10 15 0 0 2 3 5 4 1 t ? time ? s ? shutdown supply current ? shutdown pulse ? v i dd(sd) a sd pulse i dd(sd) v dd = 5 v a v = 1 v i = 2.5 v r l = 10 k ? c l = 160 pf and 10 pf t a = 25 c 5 10 15 20 25 30 figure 41 slos218f ? december 1998 ? revised january 2005 24 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 42 1 0 ?1 ?10 10 30 50 70 ? output voltage ? v 2 3 4 90 110 130 150 v o t ? time ? s sd pulse v o channel 1 v dd = 3 v a v = 1 v i = 2.5 v r l = 10 k ? c l = 160 pf and 8 pf t a = 25 c shutdown off pulse response vs time figure 43 3 2 0 ?1 ?20 0 20 40 60 80 4 5 6 100 120 140 1 t ? time ? s ? output voltage ? v v o sd pulse v o channel 1 v dd = 5 v a v = 1 v i = 4 v r l = 10 k ? c l = 160 pf and 8 pf t a = 25 c shutdown off pulse response vs time figure 44 1 0 ?1 ?2 ?1 0 1 2 3 4 2 3 shutdown on pulse response vs time 4 56 t ? time ? s ? output voltage ? v v o sd pulse v dd = 3 v a v = 1 v i = 2.5 v r l = 10 k ? t a = 25 c c l = 160 pf c l = 8 pf figure 45 3 2 0 ?1 ?2 0 2 4 6 4 5 shutdown on pulse response vs time 6 81012 1 t ? time ? s ? output voltage ? v v o sd pulse v dd = 5 v a v = 1 v i = 4 v r l = 10 k ? t a = 25 c c l = 160 pf c l = 8 pf slos218f ? december 1998 ? revised january 2005 25 www.ti.com post office box 1443 ? houston, texas 77251?1443 typical characteristics figure 46 80 60 40 0 10 100 1 k 10k shutdown reverse isolation ? db 100 120 f ? frequency ? hz shutdown reverse isolation vs frequency 140 100k 1m 10m 20 v dd = 3 v and 5 v v i(pp) = 0.1, 1.5, 2.5 v r l = 10 k ? c l = 28 pf t a = 25 c figure 47 80 60 20 0 10 100 1k 10k 100 120 shutdown forward isolation vs frequency 140 100k 1m 40 shutdown forward isolation ? db f ? frequency ? hz v dd = 3 v and 5 v v i(pp) = 0.1, 1.5, 2.5 v r l = 10 k ? c l = 28 pf t a = 25 c parameter measurement information _ + r null r l c l figure 48 slos218f ? december 1998 ? revised january 2005 26 www.ti.com post office box 1443 ? houston, texas 77251?1443 application information shutdown function three members of the tlv245x family (tlv2450/3/5) have a shutdown terminal for conserving battery life in portable applications. when the shutdown terminal is pulled to the voltage level on the gnd terminal of the device, the supply current is reduced to 16 na/channel, the amplifier is disabled, and the outputs are placed in a high impedance mode. to enable the amplifier, the shutdown terminal must be pulled high. the shutdown terminal should never be left floating. the shutdown terminal threshold is always referenced to the gnd terminal of the device. therefore, when operating the device with split supply voltages (e.g. 2.5 v), the shutdown terminal needs to be pulled to v dd ? (not system ground) to disable the operational amplifier. the amplifier?s output with a shutdown pulse is shown in figures 42, 43, 44, and 45. the amplifier is powered with a single 5-v supply and configured as a noninverting configuration with a gain of 5. the amplifier turnon and turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output waveform. the times for the single, dual, and quad are listed in the data tables. figures 46 and 47 show the amplifier?s forward and reverse isolation in shutdown. the operational amplifier is powered by 1.35-v supplies and configured as a voltage fo llower (a v = 1). the isolation performance is plotted across frequency using 0.1-v pp , 1.5-v pp , and 2.5-v pp input signals. during normal operation, the amplifier would not be able to handle a 2.5-v pp input signal with a supply voltage of 1.35 v since it exceeds the common-mode in put voltage range (v icr ). however, this curve illustrates that the amplifier remains in shutdown even under a worst case scenario. driving a capacitive load when the amplifier is configured in this manner, capacitive loading directly on the output will decrease the device?s phase margin leading to high frequency ringing or oscillations. therefore, for capacitive loads of greater than 10 pf, it is recommended that a resistor be placed in series (r null ) with the output of the amplifier, as shown in figure 49. a minimum value of 20 ? should work well for most applications. c load r f input output r g r null + ? figure 49. driving a capacitive load slos218f ? december 1998 ? revised january 2005 27 www.ti.com post office box 1443 ? houston, texas 77251?1443 application information offset voltage the output of fset voltage, (v oo ) is the sum of the input of fset voltage (v io ) and both input bias currents (i ib ) times the corresponding gains. the following schematic and formula can be used to calculate the output offset voltage: v oo v io 1 r f r g i ib r s 1 r f r g i ib r f + ? v i + r g r s r f i ib? v o i ib+ figure 50. output offset voltage model general configurations when receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often required. the simplest way to accomplish this is to place an rc filter at the noninverting terminal of the amplifier (see figure 51). v i v o c1 + ? r g r f r1 v o v i 1 r f r g 1 1 sr1c1 f ?3db 1 2 r1c1 figure 51. single-pole low-pass filter if even more attenuation is needed, a multiple pole filter is required. the sallen-key filter can be used for this task. for best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth. failure to do this can result in phase shift of the amplifier. v i c2 r2 r1 c1 r f r g r1 = r2 = r c1 = c2 = c q = peaking factor (butterworth q = 0.707) ( = 1 q 2 ? ) r g r f _ + f ?3db 1 2 rc figure 52. 2-pole low-pass sallen-key filter slos218f ? december 1998 ? revised january 2005 28 www.ti.com post office box 1443 ? houston, texas 77251?1443 application information general power dissipation considerations for a given ja , the maximum power dissipation is shown in figure 53 and is calculated by the following formula: p d t max ?t a ja where: p d = maximum power dissipation of tlv245x ic (watts) t max = absolute maximum junction temperature (150 c) t a = free-ambient air temperature ( c) ja = jc + ca jc = thermal coefficient from junction to case ca = thermal coefficient from case to ambient air ( c/w) 1 0.75 0.5 0 ?55 ?40 ?25 ?10 5 maximum power dissipation ? w 1.25 1.5 maximum power dissipation vs free-air temperature 1.75 20 35 50 0.25 t a ? free-air temperature ? c 2 65 80 95 110 125 msop package low-k test pcb ja = 260 c/w t j = 150 c pdip package low-k test pcb ja = 104 c/w soic package low-k test pcb ja = 176 c/w sot-23 package low-k test pcb ja = 324 c/w note a: results are with no air flow and using jedec standard low-k test pcb. figure 53. maximum power dissipation vs free-air temperature slos218f ? december 1998 ? revised january 2005 29 www.ti.com post office box 1443 ? houston, texas 77251?1443 application information macromodel information macromodel information provided was derived using microsim parts ? , the model generation software used with microsim pspice ? . the boyle macromodel (see note 1) and subcircuit in figure 54 are generated using the tlv245x typical electrical and operating characteristics at t a = 25 c. using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): maximum positive output voltage swing maximum negative output voltage swing slew rate quiescent power dissipation input bias current open-loop voltage amplification unity-gain frequency common-mode rejection ratio phase margin dc output resistance ac output resistance short-circuit output current limit note 1: g. r. boyle, b. m. cohn, d. o. pederson, and j. e. solomon, ?macromodeling of integrated circuit operational amplifiers,? ieee journal of solid-state circuits, sc-9, 353 (1974). pspice and parts are trademarks of microsim corporation. slos218f ? december 1998 ? revised january 2005 30 www.ti.com post office box 1443 ? houston, texas 77251?1443 application information * amp_tlv2450?x operational amplifier ?macromodel? subcircuit * created using parts release 8.0 on 10/12/98 at 11:06 * parts is a microsim product. * * connections: noninverting input * | inverting input * | | positive power supply * | | | negative power supply * | | | | output * | | | | | .subckt amp_tlv2450?x 1 2 3 4 5 * c1 11 12 354.48e?15 c2 6 7 7.5000e?12 cee 10 99 42.237e?15 dc 5 53 dy de 54 5 dy dlp 90 91 dx dln 92 90 dx dp 4 3 dx egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5 fb 7 99 poly(5) vb vc ve vlp vln 0 + 207.31e6 ?1e3 1e3 210e6 ?210e6 ga 6 0 11 12 15.254e?6 gcm 0 6 10 99 48.237e?12 iee 10 4 dc 938.61e?9 hlim 90 0 vlim 1k q1 11 2 13 qx1 q2 12 1 14 qx2 r2 6 9 100.00e3 rc1 3 11 65.557e3 rc2 3 12 65.557e3 re1 13 10 10.367e3 re2 14 10 10.367e3 ree 10 99 213.08e6 ro1 8 5 10 ro2 7 99 10 rp 3 4 147.06 vb 9 0 dc 0 vc 3 53 dc .82 ve 54 4 dc .82 vlim 7 8 dc 0 vlp 91 0 dc 38 vln 0 92 dc 38 .model dx d(is=800.00e?18) .model dy d(is=800.00e?18 rs=1m cjo=10p) .model qx1 npn(is=800.00e?18 bf=843.08) .model qx2 npn(is=800.0000e?18 bf=843.08) .ends 13 rp in+ rc1 rc2 ree egnd fb ro2 ro1 vlim out ga ioff gcm vb c1 dc iee re2 re1 dp gnd v dd+ in? q1 q2 cee c2 ve de dlp dln vln hlim vlp 14 10 4 2 1 11 12 3 53 54 96 8 5 7 91 90 92 vc 99 + + + + + + + ? ? ? ? ? ? ? ? + r2 figure 54. boyle macromodel and subcircuit packaging information orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2450aid active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450aidg4 active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450aidr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450aip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2450aipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2450cd active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450cdbvr active sot-23 dbv 6 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450cdbvrg4 active sot-23 dbv 6 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450cdbvt active sot-23 dbv 6 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450cdg4 active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450cp active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2450cpe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2450id active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450idbvr active sot-23 dbv 6 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450idbvrg4 active sot-23 dbv 6 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450idbvt active sot-23 dbv 6 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450idbvtg4 active sot-23 dbv 6 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450idg4 active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2450ip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2450ipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451aid active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451aidr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451aip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451aipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451cd active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim package option addendum www.ti.com 17-nov-2005 addendum-page 1 orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2451cdbvr active sot-23 dbv 5 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cdbvrg4 active sot-23 dbv 5 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cdbvt active sot-23 dbv 5 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cdbvtg4 active sot-23 dbv 5 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cdr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cdrg4 active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451cp active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451cpe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451id active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idbvr active sot-23 dbv 5 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idbvrg4 active sot-23 dbv 5 3000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idbvt active sot-23 dbv 5 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idbvtg4 active sot-23 dbv 5 250 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451idrg4 active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2451ip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2451ipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452aid active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452aidg4 active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452aidr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452aidrg4 active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452aip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452aipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452cd active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cdgk active msop dgk 8 80 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cdgkg4 active msop dgk 8 80 green (rohs & no sb/br) cu nipdau level-1-260c-unlim package option addendum www.ti.com 17-nov-2005 addendum-page 2 orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2452cdgkr active msop dgk 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cdgkrg4 active msop dgk 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cdr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cdrg4 active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452cp active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452cpe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452id active soic d 8 75 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452idgk active msop dgk 8 80 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452idgkr active msop dgk 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452idgkrg4 active msop dgk 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452idr active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452idrg4 active soic d 8 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2452ip active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2452ipe4 active pdip p 8 50 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2453aidr active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453aidrg4 active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453ain active pdip n 14 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2453aine4 active pdip n 14 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2453cd active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453cdgs active msop dgs 10 80 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453cdgsr active msop dgs 10 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453cdgsrg4 active msop dgs 10 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453cdr active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453cdrg4 active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453idgs active msop dgs 10 80 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453idgsr active msop dgs 10 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim package option addendum www.ti.com 17-nov-2005 addendum-page 3 orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2453idgsrg4 active msop dgs 10 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453idr active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453idrg4 active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2453in active pdip n 14 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2453ine4 active pdip n 14 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2454aid active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aidg4 active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aidr active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aidrg4 active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454ain active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc tlv2454aine4 active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc tlv2454aipw active tssop pw 14 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aipwg4 active tssop pw 14 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aipwr active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454aipwrg4 active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454cd active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454cn active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc tlv2454cne4 active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc tlv2454cpw active tssop pw 14 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454cpwr active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454cpwrg4 active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454id active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454idg4 active soic d 14 50 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454idr active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim TLV2454IDRG4 active soic d 14 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454in active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc package option addendum www.ti.com 17-nov-2005 addendum-page 4 orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2454ine4 active pdip n 14 25 pb-free (rohs) cu nipd level-nc-nc-nc tlv2454ipw active tssop pw 14 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454ipwr active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2454ipwrg4 active tssop pw 14 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455aid active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455aidr active soic d 16 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455aidrg4 active soic d 16 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455ain active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2455aine4 active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2455aipw active tssop pw 16 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455aipwr active tssop pw 16 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455aipwrg4 active tssop pw 16 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cd active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cdg4 active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cn active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2455cne4 active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2455cpw active tssop pw 16 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cpwg4 active tssop pw 16 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cpwr active tssop pw 16 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455cpwrg4 active tssop pw 16 2000 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455id active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455idg4 active soic d 16 40 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455idr active soic d 16 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455idrg4 active soic d 16 2500 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455in active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc tlv2455ine4 active pdip n 16 25 pb-free (rohs) cu nipdau level-nc-nc-nc package option addendum www.ti.com 17-nov-2005 addendum-page 5 orderable device status (1) package type package drawing pins package qty eco plan (2) lead/ball finish msl peak temp (3) tlv2455ipw active tssop pw 16 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455ipwg4 active tssop pw 16 90 green (rohs & no sb/br) cu nipdau level-1-260c-unlim tlv2455ipwrg4 active tssop pw 16 tbd call ti call ti (1) the marketing status values are defined as follows: active: product device recommended for new designs. lifebuy: ti has announced that the device will be discontinued, and a lifetime-buy period is in effect. nrnd: not recommended for new designs. device is in production to support existing customers, but ti does not recommend using this part in a new design. preview: device has been announced but is not in production. samples may or may not be available. obsolete: ti has discontinued the production of the device. (2) eco plan - the planned eco-friendly classification: pb-free (rohs) or green (rohs & no sb/br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. tbd: the pb-free/green conversion plan has not been defined. pb-free (rohs): ti's terms "lead-free" or "pb-free" mean semiconductor products that are compatible with the current rohs requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. where designed to be soldered at high temperatures, ti pb-free products are suitable for use in specified lead-free processes. green (rohs & no sb/br): ti defines "green" to mean pb-free (rohs compatible), and free of bromine (br) and antimony (sb) based flame retardants (br or sb do not exceed 0.1% by weight in homogeneous material) (3) msl, peak temp. -- the moisture sensitivity level rating according to the jedec industry standard classifications, and peak solder temperature. important information and disclaimer: the information provided on this page represents ti's knowledge and belief as of the date that it is provided. ti bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. efforts are underway to better integrate information from third parties. ti has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ti and ti suppliers consider certain information to be proprietary, and thus cas numbers and other limited information may not be available for release. in no event shall ti's liability arising out of such information exceed the total purchase price of the ti part(s) at issue in this document sold by ti to customer on an annual basis. package option addendum www.ti.com 17-nov-2005 addendum-page 6 mechanical data mpdi001a january 1995 revised june 1999 post office box 655303 ? dallas, texas 75265 p (r-pdip-t8) plastic dual-in-line 8 4 0.015 (0,38) gage plane 0.325 (8,26) 0.300 (7,62) 0.010 (0,25) nom max 0.430 (10,92) 4040082/d 05/98 0.200 (5,08) max 0.125 (3,18) min 5 0.355 (9,02) 0.020 (0,51) min 0.070 (1,78) max 0.240 (6,10) 0.260 (6,60) 0.400 (10,60) 1 0.015 (0,38) 0.021 (0,53) seating plane m 0.010 (0,25) 0.100 (2,54) notes: a. all linear dimensions are in inches (millimeters). b. this drawing is subject to change without notice. c. falls within jedec ms-001 for the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm mechanical data mtss001c january 1995 revised february 1999 post office box 655303 ? dallas, texas 75265 pw (r-pdso-g**) plastic small-outline package 14 pins shown 0,65 m 0,10 0,10 0,25 0,50 0,75 0,15 nom gage plane 28 9,80 9,60 24 7,90 7,70 20 16 6,60 6,40 4040064/f 01/97 0,30 6,60 6,20 8 0,19 4,30 4,50 7 0,15 14 a 1 1,20 max 14 5,10 4,90 8 3,10 2,90 a max a min dim pins ** 0,05 4,90 5,10 seating plane 0 8 notes: a. all linear dimensions are in millimeters. b. this drawing is subject to change without notice. c. body dimensions do not include mold flash or protrusion not to exceed 0,15. d. falls within jedec mo-153 important notice texas instruments incorporated and its subsidiaries (ti) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. all products are sold subject to ti?s terms and conditions of sale supplied at the time of order acknowledgment. ti warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ti?s standard warranty. testing and other quality control techniques are used to the extent ti deems necessary to support this warranty. except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. ti assumes no liability for applications assistance or customer product design. customers are responsible for their products and applications using ti components. to minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. ti does not warrant or represent that any license, either express or implied, is granted under any ti patent right, copyright, mask work right, or other ti intellectual property right relating to any combination, machine, or process in which ti products or services are used. information published by ti regarding third-party products or services does not constitute a license from ti to use such products or services or a warranty or endorsement thereof. use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ti under the patents or other intellectual property of ti. reproduction of information in ti data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. reproduction of this information with alteration is an unfair and deceptive business practice. ti is not responsible or liable for such altered documentation. resale of ti products or services with statements different from or beyond the parameters stated by ti for that product or service voids all express and any implied warranties for the associated ti product or service and is an unfair and deceptive business practice. ti is not responsible or liable for any such statements. following are urls where you can obtain information on other texas instruments products and application solutions: products applications amplifiers amplifier.ti.com audio www.ti.com/audio data converters dataconverter.ti.com automotive www.ti.com/automotive dsp dsp.ti.com broadband www.ti.com/broadband interface interface.ti.com digital control www.ti.com/digitalcontrol logic logic.ti.com military www.ti.com/military power mgmt power.ti.com optical networking www.ti.com/opticalnetwork microcontrollers microcontroller.ti.com security www.ti.com/security telephony www.ti.com/telephony video & imaging www.ti.com/video wireless www.ti.com/wireless mailing address: texas instruments post office box 655303 dallas, texas 75265 copyright ? 2005, texas instruments incorporated |
Price & Availability of TLV2454IDRG4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |