asahi kasei [AKD5359-b] 2005/07 - 1 - general description AKD5359-b is an evaluation board for the digital audio 24bit 96khz a/d converter, ak5359. AKD5359-b has analog input circuits and a digital interface transmitter,and can achieve the interface with digital audio systems via opt-connector. ? ordering guide AKD5359-b --- ak5359 evaluation board function ? dit (ak4114) with optical output lin rin va,vd ak4114 (dit) opt out dsp data 10pin header agnd,dgnd ak5359 figure 1 AKD5359-b block diagram * circuit diagram and pcb layout are attached at the end of this manual. a k5359 evaluation board rev.0 a kd5359-b
asahi kasei [AKD5359-b] 2005/07 - 2 - 1. evaluation board manual ? operation sequence 1) set up the power supply lines. [va] (red) = 2.7 5.5v or +15v : for va of ak5359 (typ. 5.0v) [vd] (orange) = 2.7 5.5v : for vd of ak5359, 74hc14 (typ. 5.0v) [vcc] (red) = 3.3v : for ak4114 [agnd] (black) = 0v : for analog ground [dgnd] (black) = 0v : for logic ground each supply line should be distri buted from the power supply unit. 2) set up the evaluation mode, jumper pins and dip switches. (see the followings.) 3) power on. the ak5359 and ak4114 should be reset once bringing sw2 = ?l? upon power-up. ? evaluation mode (1) slave mode (1-1) a/d evaluation using dit function of ak4114 port2 (dit) is used. dit generates audio bi-phase signal from received data and which is output through optical connector (totx141). it is possible to connect akm?s d/a converter evaluation boards on the digital-amplifier, which equips dir input. nothing should be connected to port1 (dsp). jp5 mclk (1-2) all interface signals including master clock are fed externally. port1 (dsp) is used. all interface signals (mclk, sclk, lrck) are provided to the ak5359 through port1. jp5 (mclk) should be open. the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk
asahi kasei [AKD5359-b] 2005/07 - 3 - (2) master mode (2-1) a/d evaluation using dit function of ak4114 port2 (dit) is used. dit generates audio bi-phase signal from received data and which is output through optical connector (totx141). it is possible to connect akm?s d/a converter evaluation boards on the digital-amplifier, which equips dir input. nothing should be connected to port1 (dsp). the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk (2-2) master clock is fed externally. port1 (dsp) is used. mclk is provided to the ak 5359 through port1. jp5 (mclk) should be open. the dif1 of sw1 (mode) should be set to ?h?. jp5 mclk ? other jumper pins set up 1. jp1 (gnd) : analog ground and digital ground open : separated. short : common. (the connector ?dgnd? can be open.) 2. jp2 (cks1) : setting of cks1 pin for ak5359 h : master mode l : slave mode 3. jp3 (va) : select va for ak5359 va : supply from va connector reg : supply from regulator. va connector should be supplied +15v. 4. jp4 (vd) : select vd for ak5359 va : supply from va connector vd : supply from vd connector
asahi kasei [AKD5359-b] 2005/07 - 4 - ? dip switch set up [sw1] (mode1): setting the evaluation mode for ak5359 and ak4114 on is ?h?, off is ?l?. cks1 should be set by jp2. no. name off (?l?) on (?h?) 1 cks0 2 cks2 see table 2 3 dif msb justified i 2 s compatible 4 dif1 ak4114 master mode ak4114 slave mode table 1. mode setting cks2 cks1 cks0 hpf master/slave mclk sclk l l l on slave 128/192fs (108k |