85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 1 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com applications ? ? product features ? ? ? ? ? ? ? 5.0 x 5.0 x 1.32?mm ? ? ? smp - 20, 5.0 x 5.0 x 1.32?mm functional block diagram top view pin configuration pin no. label 2 input 6 output 3,7 ground 1,4 , 5 ,8 case ground general description the 855770 is a high - performance if saw filter with a center frequency of 190 mhz and a usable bandwidth of 5 mhz. it features low loss with excellent attenuation, and is designed to be used with a balanced input and output. the device is rohs compliant and pb - free. ordering information part no. description 855770 packaged part 855770 - evb evaluation board standard t/r size = 4 000 units/reel pb 4 8 7 6 5 1 2 3 input output gnd gnd gnd gnd gnd gnd
85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 2 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com absolute maximum ratings parameter rating 1. operation of this device outside the parameter ranges given may cause permanent damage. 2. specifications are not guar anteed over all operable conditions. storage temperature (1) - ? 40 to + ? 85 ? c operable temperature ( 2 ) - ? 40 to + ? 85 ? c electrical specifications ? (1) test conditions unless otherwise noted: (2) temperature range - ? 30 to + ? 70 ? c paramete r (3) conditions min typical (4) max units center frequency - 190 - mhz insertion loss at 190 mhz - 8 10 db lower 5 ?db band edge? (5) upper 5 ?db band edge ? (5) - 192.4 187.23 193.01 187.6 - mhz phase ripple ? ? 188? C ?192?mhz ? ( 5 ) ? C ? ? C ? 180? C ? 194.5? C ?200? mhz ? 200? C ?210?mhz ? 210? C ?220?mhz ? ( 6 ) single - ended - 50 - ? notes: 1. all specificati ons are based on the triquint schematic reference design shown on page 3 . 2. in production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature . 3. electrical margin has been built into the d esign to account for the variations due to temperature drift and manufacturing tolerances . 4. typical values are based on average measurements at room temperature . 5. relative to insertion lo ss at center frequency. 6. this is the optimum impedance in order to achie ve the performance shown.
85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 3 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com evaluation board notes: 3 - layer s board - top, middle & bottom layer: 1 oz copper substrates: .031 thick fr4 dielectric. finish plating: nickel: 3 - 8 ? m thick, gold: .03 - .2 ? m thick hole plating: copper min .0008 ? m thick pcb mounting pattern notes : 1. all dimensions are in millimeters. angles are in degrees. 2. this drawing specifies the mounting pattern used on the triquint evaluation board for this product. some modification may be necessary to suit end user assembly materials and processes. bill of mat erial reference des. d1 value description manuf. part number l1 56 ?nh 0402, ?5? ?nh ?5? ? ?? ?pf ?5 a jjjym ?? ?? ?? ?? ?????? 1 , 3 , 4 5 , 7 , 8 5 0 ? ? 1.47 5.20 2.28 .84 1.47 .84 .43 .71
85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 4 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com performance plots (test conditions unless otherwise noted: t emp.= + ? 25? ? c) frequency response d b frequency (mhz) -60 -50 -40 -30 -20 -10 0 160 175 190 205 220 passband response d b frequency (mhz) -15 -13 -11 -9 -7 185.2 187.6 190 192.4 194.8 wideband response d b frequency (mhz) -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 100 200 300 400 500 phase response d e g frequency (mhz) -2 -1 0 1 2 188 189 190 191 192 input smith chart -1 -0 .8 -0 .6 -0 .4 -0 .2 0 0.2 0.4 0.6 0.8 1 -1 -0 .5 0 0.5 1 output smith chart -1 -0 .8 -0 .6 -0 .4 -0 .2 0 0.2 0.4 0.6 0.8 1 -1 -0 .5 0 0.5 1
85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 5 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com mechanical information package style: smp - 2 0a dimensions: 5.00 x 5.00 x 1.32 mm body: al 2 o 3 ceramic lid: kovar , ni plated terminations: au plating 0.5 - 1.0m, over a 2 6m ni plating all dimensions shown are nom inal in millimeters all tolerances are 0.15mm except overall length and width 0.10mm the date code consists of: day of the current year (julian, 3 digits), y = last digit of the year, and m = manufacturing site code notes: 1. all dimensions shown are typic al in millimeters 2. an asterisk (*) in front of the marking code indicates prototype. tape and reel information standard t/r size = 4 0 00 units ? / ? reel . all dimensions are in millimeters 1.32 nom. 1.52 max. 0.66 1.27 1.27 0.64 2.08 5.00 5.00 date code a jjjym id dot logo sawtek code marking 1.75 5.5 2.0 4.0 8.0 ?1.5 ?1.5 5.25 5.25 1.8 0.3 a a section a-a 12.0 12.8 2.7 ?13.0 ?20.2 ?330 logo sawtek id dot 2.0 ?102 direction of travel
85 5770 190 mhz saw filter data s heet: rev . b 14 - 06 - 16 - 6 of 6 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: 1c value: passes ? esd rating: b value: passes ? solderability compatible with both lead - free (260 ? ? soldering profile for recommended guidelines. rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? ? ? ? 15 h 12 br 4 0 2 ) free ? ? msl rating not applicable. her metic package. contact information for the latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1 .407.886.8860 email: info - sales@tqs.com fax: +1.407.886.7061 for technical questions and application information: email: flapplication.engineering @tqs.com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information co ntained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such infor mation is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or a ny use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint p roducts are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
|
