active pfc - meets en61000-3-2, -3 small size 3.0?x 5.0?x 1.25 single, triple & quad outputs overvoltage & overcurrent protection power fail detect international safety approvals input ac input voltage 90-264 vac input frequency 47-63 hz power factor 0.98 typical inrush current 24 a max at 100 vac input current 0.8 a max at 240 vac 1.8 a max at 100 vac output output voltage see table output power 125 watts minimum load 5 w minimum load on any output or combination of outputs required to maintain regulation line/load regulation see table ripple and noise ?% pk-pk maximum > = 5 v out ?% maximum transient response 5% max deviation, recovering to a 1% of final value in less than 500 ? after a 25% load change temperature 0.04%/? maximum coefficient hold up time >28 ms minimum at full load overvoltage v1 & v2: 113% to 148% recycle input protection to reset overcurrent all outputs 115% to 135% with protection auto recovery remote sense v1 only compensates for 0.5 v drop not available on ifc125-31 general efficiency 83% typical power density 6.66 w/in 3 mtbf >220,000 hours per bellcore isolation voltage 3000 vac input to output 1500 vac input to ground 500 vac output to ground signals power good - on = logic hi size 5.00?x 3.00?x 1.25 weight 312 grams approx. environmental operating -25 ? to +70 ? derate linearly from temperature 100% load at +70 ? to 50% load at +50 ? cooling 5 cfm forced air required for 125 w humidity 5-95% rh, non-condensing storage temperature -40 ? to +85 ? emc & safety safety approvals ul60950, csa22.2: 60950 per cul, en60950, ce mark lvd emi/emc meets en61000-3-2, -3 en55022/cispr22 class b and fcc class b conducted 125 watts ifc125 series ac/dc open frame specification i ntelligent design q uality product xpiq inc. ph: 508 429.9883 fax: 800 226.2100 email: sales@xpiq.com holliston, ma 01746 usa www. xp i q .com
output voltage & current ratings ifc125 mechanical details notes 1. total regulation includes tolerance, line regulation and load regulation. 2. maximum output power not to exceed 125 w with 5 cfm forced air or 70 w with convection cooling. 3. for models IFC125-40-1 and -42-3, a maximum of 80 w combined +2.5 v or +3.3 v and +5 v outputs with 5 cfm of forced air cooli ng or 40 w with convection cooling. 4. 5 w minimum load required to maintain regulation. output 1 output 2 output 3 output 4 model vnom imax reg (1) vnom imax reg (1) vnom imax reg (1) vnom imax reg (1) number 24.0 v 5.2 a ?% 12.0 v 0.5 a ?% ifc125-14 5.0 v 16.5 a ?% 12.0 v 5.0 a ?% -12.0 v 0.5 a ?% ifc125-31 2.5 v 12.5 a ?% 5.0 v 15.0 a ?% 12.0 v 5.0 a ?% -12.0 v 0.5 a ?% IFC125-40-1 3.3 v 10.0 a ?% 5.0 v 15.0 a ?% 12.0 v 5.0 a ?% -12.0 v 0.5 a ?% ifc125-42-3 pin 1 neutral pin 2 missing pin pin 3 line j1-ac input connector all models. ph: 508 429.9883 fax: 800 226.2100 email: sales@xpiq.com holliston, ma 01746 usa www. xp i q .com mechanical drawing for ifc125-31, -40-1 and -42-3 only. see next page for ifc125-14 j2 - dc output connector ifc125-31 IFC125-40-1 ifc125-42-3 pin 14 +5 vdc +5 vdc +5 vdc pin 13 +5 vdc +5 vdc +5 vdc pin 12 +5 vdc +5 vdc +5 vdc pin 11 +5 vdc +5 vdc +5 vdc pin 10 dc gnd dc gnd dc gnd pin 9 dc gnd dc gnd dc gnd pin 8 dc gnd dc gnd dc gnd pin 7 dc gnd dc gnd dc gnd pin 6 dc gnd dc gnd dc gnd pin 5 not used. +2.5 vdc +3.3 vdc pin 4 not used. +2.5 vdc +3.3 vdc pin 3 not used +2.5 vdc +3.3 vdc pin 2 +12 vdc +12 vdc +12 vdc pin 1 -12 vdc -12 vdc -12 vdc ifc125-31 IFC125-40-1 ifc125-42-3 pin 1 0v sense 0v sense 0v sense pin 2 not used +2.5 v sense +3.3 v sense pin 3 power good power good power good j3-remote sense & power good connector note: j3-1 must be connected to dc gnd at output or at load. j3-2 must be connected to output 1 at the output or load ifc125-31 ifc125-42-3 &-40-1 j1 housing 09-50-8031 90-50-8033 pins 08-52-0113 08-52-0113 j2 housing 09-50-8141 09-50-8143 pins 08-52-0113 08-52-0113 j3 housing 22-01-3037 22-01-3037 pins 08-50-0114 08-50-0114 mating connectors with molex part numbers
ph: 508 429.9883 fax: 800 226.2100 email: sales@xpiq.com holliston, ma 01746 usa www. xp i q .com mechanical details pin 1 neutral pin 2 missing pin pin 3 line j1 - ac input connector. mechanical drawing for ifc125-14 only. ifc125-14 pin 1 +24 vdc pin 2 +24 vdc pin 3 +24 vdc pin 4 dc gnd pin 5 dc gnd pin 6 dc gnd j2 - dc output connector ifc125-14 pin 1 return pin 2 -sense pin 3 +sense pin 4 current share pin 5 power good pin 6 ps ok j3 - remote sense connector j1 housing 09-50-8031 pins 08-52-0113 j2 housing 09-50-8061 pins 08-52-0113 j3 housing 22-01-3067 pins 08-50-0114 j4 housing 22-01-3027 pins 08-50-0114 mating connectors with molex part numbers ifc125-14 pin 1 +12 vdc pin 2 +12v return j4 - aux output connector
|