dle45/60 series led drivers xxx series www.xppower.com 1 notes 1. typical efficiency at full load and 230 vac input. ? ac input led driver ? constant voltage/constant current operation ? constant current dimming versions ? high efficiency ? water proof to ip67 ? class 2 ? 3 year warranty dimensions: dle45/60: 6.73 x 1.78 x 1.27 (164.1 x 45.3 x 32.5 mm) 45/60 watts models & ratings constant voltage / constant current models output power output voltage output current output voltage range in constant current mode ovp range efficiency (1) model number 45 w 24 v 1850 ma 16 - 24 v 26.4-31.2 v 85.0% dle45ps24 45 w 36 v 1250 ma 24 - 36 v 39.6-46.8 v 86.0% dle45ps36 48 w 48 v 1000 ma 34 - 48 v 52.8-62.4 v 87.0% dle45ps48 40 w 57 v 700 ma 40 - 57 v 62.9-70.0 v 87.0% dle45ps57 50 w 12 v 4200 ma 9 - 12 v 13.2-15.6 v 86.0% dle60ps12 60 w 24 v 2500 ma 16 - 24 v 26.4-31.2 v 86.0% dle60ps24 60 w 36 v 1650 ma 24 - 36 v 39.6-46.8 v 87.0% dle60ps36 60 w 48 v 1250 ma 34 - 48 v 52.8-62.4 v 88.0% dle60ps48 60 w 57 v 1050 ma 40 - 57 v 62.9-70.0 v 88.0% dle60ps57 models & ratings dimmable models output power output voltage output current output voltage range in constant current mode ovp range efficiency (1) model number 45 w 24 v 1850 ma 16 - 24 v 26.4-31.2 v 85.0% dle45ps1850-ad 45 w 36 v 1250 ma 24 - 36 v 39.6-46.8 v 86.0% dle45ps1250-ad 48 w 48 v 1000 ma 34 - 48 v 52.8-62.4 v 87.0% dle45ps1000-ad 40 w 57 v 700 ma 40 - 57 v 62.9-70.0 v 87.0% dle45ps700-ad 50 w 12 v 4200 ma 9 - 12 v 13.2-15.6 v 86.0% DLE60PS4200-AD 60 w 24 v 2500 ma 16 - 24 v 26.4-31.2 v 86.0% dle60ps2500-ad 60 w 36 v 1650 ma 24 - 36 v 39.6-46.8 v 87.0% dle60ps1650-ad 60 w 48 v 1250 ma 34 - 48 v 52.8-62.4 v 88.0% dle60ps1250-ad 60 w 57 v 1050 ma 40 - 57 v 62.9-70.0 v 88.0% dle60ps1050-ad the dle series of ac input led drivers incorporate universal input with active power factor correction in a two power stage design, eliminating flicker while providing a high efficiency solution. designed as a class ii isolation product, without the need for a safety earth, dle series led drivers are also approved as a class 2 limited power source, making them suitable for a wide range of applications. dimmable constant current versions are available with the facility for pwm, voltage and resistance programming.
dle series www.xppower.com 2 led drivers input output characteristic minimum typical maximum units notes & conditions output voltage 12 57 vdc see models and ratings table minimum load no minimum load required start up delay 1.5 s measured at 115 vac hold up time 20 ms line regulation 0.5 % load regulation 1 % constant voltage mode 5 constant current mode turn on overshoot 7% constant voltage mode transient response 4% deviation, recovery to within 1% in 10 ms for a 50% load change ripple & noise 200/250 mv pk-pk 24 v/>24 v. measured using 12 twisted pair with 0.1 f and 47 f capacitors in parallel at 20 mhz bandwidth, at 25 c overvoltage protection see models and ratings table, recycle ac to reset overload protection 95 105 % auto recovery short circuit protection trip & restart (hiccup mode) temperature coefficient 0.04 %/?c characteristic minimum typical maximum units notes & conditions input voltage - operating 90 305 vac see derating curve input frequency 47 63 hz power factor >0.9 measured at 230 vac, full load input current 0.6 a 115 vac 0.3 230 vac inrush current 45 a 230 vac cold start, +25 oc input protection internal t1.0 a/250 v fuse fitted in line general characteristic minimum typical maximum units notes & conditions efficiency 87 % see models and tables isolation: input to output 3750 vac switching frequency 100 khz mean time between failure >200 khrs mil-hdbk-217f at 25 c gb weight 0.9 (410) lb (kg) 100 10 20 30 40 50 60 70 80 90 vo max vo min 0 output current (%) output voltage trip & restart zone load regulation in constant current mode constant current curve
dle series www.xppower.com led drivers 3 environmental characteristic minimum typical maximum units notes & conditions operating temperature -20 +50 c see derating curve operating humidity 5 100 % rh, non-condensing storage temperature -40 +80 c some specification parameters maybe exceeded until after 20 minutes warm up period. operating altitude 3000 m shock 30 g pk, half sine, 6 axes en60068-2-27, -2-47 & mil-std-810f 514.5 cat 4 vibration 10-500 hz, 2 g, 10 mins/cycle, 6 cycles in each of axes derating curves safety approvals emc: immunity phenomenon standard test level criteria notes & conditions equipment for general lighting purposes en61547 as below as below esd immunity en61000-4-2 a 8 kv air and 4 kv contact radiated immunity en61000-4-3 2a eft/burst en61000-4-4 2a surges en61000-4-5 installation class 3 a conducted en61000-4-6 2a magnetic field en61000-4-8 2a dips and interruptions en61000-4-11 dip: 30%, 10 ms a dip: 30%, 200 ms a/b at 230 vac/100 vac int: 100%, 8.3 ms a/b at 230 vac/100 vac emc: emissions phenomenon standard test level criteria notes & conditions conducted en55015 class b radiated en55015 class b harmonic current en61000-3-2 class c voltage fluctuations en61000-3-3 safety agency safety standard notes & conditions ul ul8750 tuv en61347 ce ce mark iec iec61347-2-13 used in conjunction with iec61347-1 ip iec60529 0 10 20 30 40 50 60 70 20 40 60 80 100 0 -20 -10 temp (?c) load (%) 100 305 90 20 40 60 80 100 0 input voltage (vac) load (%)
dle series www.xppower.com 4 led drivers 1. dimensions shown in inches (mm). 2. weight: 2.8 lb (1.27 kg). 3.tolerance: 0.x = 0.008 (0.2) 0.xx = 0.002 (0.05) notes mechanical details constant voltage / constant current mechanical details dimmable version ul 2464 18 awg 2c sjtw 18 awg 2c ac n (blue) ac l (brown) v+ (red) v- (black) 1.27 (32.5) 6.46 (164.1) 0.13 (3.5) 0.13 (3.5) 1.78 (45.3) 1.27 0.7 (150.0 20.0) 1.27 0.7 (150.0 20.0) 6.73 (171.1) 0.13 (3.5) 0.13 (3.5) r1.8 1.27 (32.5) 6.46 (164.1) 0.13 (3.5) 0.13 (3.5) 1.78 (45.3) 1.27 0.7 (150.0 20.0) 1.27 0.7 (150.0 20.0) 6.73 (171.1) 0.13 (3.5) 0.13 (3.5) r1.8 sjtw 18awg 2c ac l(brown) ac n(blue) ul 2464 18awg 4c dim+ (blue) dim- (white) v- (black) v+ (red)
dle series led drivers dim+ v+ v- dle dim- connect a variable resistor between dim+ and dim-. the dimmed output current can be determined using the equation: where the value of r is between 10 k ? and 100 k ? . the corresponding range of output current is 10% to 100% a pulse width modulated ( pwm ) signal with duty cycle d pwm can be applied between dim+ and dim-. the dimmed output current is given by: where dpwm is the % of duty cycle between 10% and 100%. the corresponding range of output current is 10% to 100%. pwm frequency should be in the range 0.5 khz to 5 khz the dimmed output current is given by: where v is the value of control voltage in the range of 1.0 v to 10.0 vdc. the corresponding range of output current is 10% to 100%. connect a variable voltage betwen dim+ and dim- output current adjustment by variable resistor output current adjustment by dc voltage output current adjustment by pwm dimmed current 100 k maximum current x r = dimmed current 10 k maximum current x v = = dimmed current maximum current x d pwm % (dpwm = pwm duty cycle) v+ v- dle dim+ + dim- dle dim- gnd pwm 0 v 10 v dim+ v+ v- 5 www.xppower.com 06feb14
|
