View NL204153AC21-17_7869934.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: dod-pp-1266 (2nd edition) published date: september 2011 cp (n) ? nlt technologies, ltd. 2011 all rights reserved. 1 this preliminary data sheet is updated document from dod-pp-1243(1). all information is subject to change without notice. please confirm the sales representative before starting to design your system. tft color lcd module NL204153AC21-17 54cm (21.3 type) qxga lvds interface (4 ports) preliminary data sheet dod-pp-1266 (2nd edition)
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 2 introduction the copyright to this document belongs to nlt technologies, ltd. (hereinafter called "nlt"). no part of this document will be used, reproduced or copied without prior written consent of nlt. nlt does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. no license, express or implied, is granted under any patent, copyright or other intellectual property right of nlt. some electronic parts/components would fail or malfunction at a certain rate. in spite of every effort to enhance reliability of products by nlt, the possibili ty of failures and malfunction might not be avoided entirely. to prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, eac h customer is required to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure. the products are classified into three quality grades: "standard" , "special" , and "specific" of the highest grade of a quality assurance program at the choice of a customer. each quality grade is designed for applications described below. any customer who intends to use a product for application other than that of standard quality grade is required to contact an nlt sales representative in advance. the standard quality grade applies to the products developed, designed and manufactured in accordance with the nlt standard quality assurance pr ogram, which are designed for such application as any failure or malfunction of the pr oducts (sets) or parts/components in corporated therein a customer uses are, directly or indirectly, free of any damage to death, human bodily injury or other property, like general electronic devices. examples: computers, office automation equipment, communications equipment, test and measurement equipment, audio and visual equipment, home el ectronic appliances, machine tools, personal electronic equipment, industrial robots, etc. the special quality grade applies to the products developed, designed and manufactured in accordance with an nlt quality assurance program stricter than the standard one, which are designed for such application as any failure or malfunction of the produc ts (sets) or parts/components incorporated therein a customer uses might directly cause any damage to death, human bodily injury or other property, or such application under more severe condition than that defined in the standard quality grade without such direct damage. examples: control systems for transp ortation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, medical equipment not specifically designed for life support, safety equipment, etc. the specific quality grade applies to the products developed, designed and manufactured in accordance with the standards or quality assurance program designated by a customer who requires an extremely higher level of reliability and quality for such products. examples: military systems, aircraft control equipment, aerospace equipment, nuclear reactor control systems, medical equipment/device s/systems for life support, etc. the quality grade of this product is the "standard" unless otherwise specified in this document.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 3 contents introduction ............................................................................................................................... ..............2 1. outline ......................................................................................................................................................4 1.1 structure and princi ple.............................................................................................................4 1.2 application................................................................................................................ .........................4 1.3 features................................................................................................................... ............................4 2. general specifications ...................................................................................................................5 3. block diagram .....................................................................................................................................6 4. detailed specifications ..................................................................................................................7 4.1 mechanical specifica tions........................................................................................................7 4.2 absolute m aximum ratings ................................................................................................... ...7 4.3 electrical c haracteristics................................................................................................. ....8 4.3.1 lcd panel signal processing board ........................................................................................ ...........8 4.3.2 led driv er board ......................................................................................................... .....................9 4.3.3 led driver bo ard current wave ............................................................................................ ............9 4.3.4 power supply voltage ripple.............................................................................................. .................10 4.3.5 fuse..................................................................................................................... ...............................10 4.4 power supply vo ltage sequence ............................................................................................11 4.4.1 lcd panel signal processing board ........................................................................................ ...........11 4.4.2 led driver board ......................................................................................................... ......................11 4.5 connections and function s for interface pins.............................................................12 4.5.1 lcd panel signal processing board ........................................................................................ ...........12 4.5.2 led driver board ......................................................................................................... ......................15 4.5.3 positions of socket ...................................................................................................... .......................16 4.6 luminance control.......................................................................................................... .............17 4.6.1 luminance control methods................................................................................................ ...............17 4.6.2 detail of brtp timing .................................................................................................... ...................18 4.7 method of connection for lvds transmitter................................................................19 4.8 display colors and input data signals ..............................................................................21 4.9 input si gnal ti mings....................................................................................................... ...............22 4.9.1 timing characteristics ................................................................................................... .....................22 4.9.2 input signal timing chart ................................................................................................ ....................22 4.10 lvds data tara nsmission method ........................................................................................23 4.11 display positions......................................................................................................... ..................23 4.12 pixel arrangnm ent ......................................................................................................... ............24 4.13 optics.................................................................................................................... ...............................25 4.13.1 optical ch aracteristics................................................................................................. .....................25 4.13.2 definition of contrast ratio............................................................................................ ...................26 4.13.3 definition of luminance uniformity ...................................................................................... ...........26 4.13.4 definition of color uniformity .......................................................................................... ...............26 4.13.5 definition of response times ............................................................................................ ................27 4.13.6 definition of viewing angles............................................................................................ ................27 5. estimated luminance lifetime ..................................................................................................27 6. reliability tests ............................................................................................................................... ..28 7. precautions ............................................................................................................................... .............29 7.1 meaning of c aution signs ................................................................................................... .......29 7.2 caut ions ................................................................................................................... ...........................29 7.3 attentions ................................................................................................................. .........................29 7.3.1 handling of the product .................................................................................................. ...................29 7.3.2 environment.............................................................................................................. .........................30 7.3.3 characteristics.......................................................................................................... ..........................31 7.3.4 others................................................................................................................... ..............................31 8. outline drawings ............................................................................................................................... 32 8.1 front view ................................................................................................................. .........................32 8.2 rear view .................................................................................................................. ..........................33 revision history ............................................................................................................................... .......34
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4 1. outline 1.1 structure and principle color lcd module NL204153AC21-17 is composed of the amorphous silicon thin film transistor liquid crystal display (a-si tft lcd) panel structure with driver lsis for driving the tft (thin film transistor) array and a backlight. the a-si tft lcd panel structure is injected liquid crystal material into a narrow gap between the tft array glass substrate and a color-filter glass substrate. color data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver lsis which drive the individual tft arrays. the tft array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. co lor images are created by regulating the amount of transmitted light through the tft array of red, green and blue dots. 1.2 application ? color monitor system 1.3 features ? ultra-wide viewing angle (adoption of ultra-advanced super fine tft (ua-sft)) ? wide color gamut ? high luminance ? high contrast ? low reflection ? 1,024 gray scale in each r, g, b sub-pixel (10-bit), 1,073,741,824 colors ? lvds interface ? selectable lvds data input map ? small foot print ? long life led backlight type with an led driver board
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 2. general specifications display area 433.152 (h) 324.864 (v) mm diagonal size of display 54cm (21.3 inches) drive system a-si tft active matrix display color 1,073,741,824 colors pixel 2,048 (h) 1,536 (v) pixels (1 pixel consists of 3 sub-pixels (rgb).) pixel arrangement rgb (red dot, green dot, blue dot) vertical stripe sub-pixel pitch 0.0705 (h) 0.2115 (v) mm pixel pitch 0.2115 (h) 0.2115 (v) mm module size 457.0 (w) 350.0 (h) 21.5 (d) mm (typ.) weight (2,700)g (typ.) contrast ratio 1,400:1 (typ.) viewing angle at the contrast ratio 10:1 ? horizontal: right side 88 (typ.), left side 88 (typ.) ? vertical: up side 88 (typ.), down side 88 (typ.) designed viewing direction viewing angle with optimum grayscale ( P dicom): normal axis (perpendicular) note1 polarizer surface antiglare polarizer pencil-hardness 2h (min.) [by jis k5600] color gamut at lcd panel center (72) % (typ.) [against ntsc color space] response time ton+toff (10% 90%) (40) ms (typ.) luminance at the maximum luminance control 800cd/m 2 (typ.) signal system 4 ports lvds interface (thc63lvd104s 2pcs, thine electronics, inc. or equivalent) [rgb 10-bit signals, data enable signal (de), dot clock (ck)] power supply voltage lcd panel signal processing board: 12.0v led driver board: 12.0v backlight led backlight type with led driver board power consumption at checkered flag pattern, the maximum luminance control (58)w (typ.) 2 2 2 note1: when the product luminance is 450 cd/m 2 , t he gamma characteristic is designed to P dicom. 5
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 3. block diagram controller i/f lcd module (product) vdd gnd 6144 lines tft lcd panel h: 2048 3 (r, g, b) v: 1536 1536 lines dc0+/? dc1+/? dc2+/? ckc+/? dc3+/? dc4+/- dd0+/? dd1+/? dd2+/? ckd+/? dd3+/? dd4+ / - da0+/? da1+/? da2+/? cka+/? da3+/? da4+/- db0+/? db1+/? note 3 note 3 lvds receiver lvds receiver db2+/? ckb+/? db3+/? db4+ / - lvds receiver note 3 note 3 lvds receiver fuse h-driver v-driver v-driver dc/dc converter power supply for gradation fuse backli g ht power supply for com led driver board fg vddb brtc brth brti brtp pwsel gndb n ote1, note2 note1: relations between gnd (signal ground), fg (frame ground) and gndb (led driver board ground) in the lcd module are as follows. gnd - fg connected gnd - gndb not connected fg - gndb not connected note2 gnd, fg and gndb must be connected to cust omer equipment's ground, and it is recommended that these grounds be connected together in customer equipment. note3 each pair of the lvds signal has a 100 terminating resistance between d+ and d-. 6
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4. detailed specifications 4.1 mechanical specifications parameter specification unit module size 457.0 1.0 (w) 350.0 1.0 (h) 21.5 (typ., d) 23.0 (max. d) note1, note2 mm display area 433.152 (h) 324.864 (v) note2 mm weight (2,700) (typ.), (2,980) (max.) g 2 2 note1: excluding warpage of the cover for led driver board. note2: see " 8. outline drawings ". 4.2 absolute maximum ratings parameter symbol rating unit remarks lcd panel signal processing board vdd -0.3 to +14.0 v power supply voltage led driver board vddb -0.3 to +15.0 v - lcd panel signal processing board note1 vi -0.3 to +2.8 v vdd= 12.0v brti signal vbi -0.3 to +1.5 v brtp signal vbp -0.3 to +5.5 v brtc signal vbc -0.3 to +5.5 v input voltage for signals led driver board pwsel signal vbs -0.3 to +5.5 v vddb= 12.0v storage temperature tst -20 to +60 c - front surface topf (0 to +60) c note2 operating temperature rear surface topr (0 to + 60) c note3 95 % ta 40 c 85 % 40 c < ta 50 c relative humidity note4 rh 70 % 50 c < ta 55 c absolute humidity note4 ah 73 note5 g/m 3 ta > 55 c operating altitude - 4,850 m 0 c ta 55 c storage altitude - 13,600 m -20 c ta 60 c 2 2 note1: da0+/-, da1+/-, da2+/-, da3+/-, da4+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, db4+/-, ckb+/-, dc0+/-, dc1+/-, dc2+/-, dc3+/-, dc4+ /-, ckc+/-, dd0+/-, dd1+/-, dd2+/-, dd3+/-, dd4+/-, ckd+/-,bsel. note2: measured at lcd panel surface (including self-heat) note3: measured at lcd module's rear shield surface (including self-heat) note4: no condensation note5: water amount at ta= 55c and rh= 70% 7
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.3 electrical characteristics 4.3.1 lcd panel signal processing board (ta= 25 c) parameter symbol min. typ. max. unit remarks power supply voltage vdd 10.8 12.0 13.2 v - power supply current idd - (590) note1 (980) note2 ma at vdd= 12.0v permissible ripple voltage vrp - - 100 mvp-p for vdd high vth - - +100 mv differential input threshold voltage low vtl -100 - - mv at vcm= 1.2v note3, note4 input voltage swing vi 0 - 2.4 v note4 terminating resistance rt - 100 - - 2 note1: checkered flag pattern (by eiaj ed-2522) note2: pattern fo r maximum current note3: common mode voltage for lvds driver note4: da0+/-, da1+/-, da2+/-, da3+/-, da4+/-, cka+/-, db0+ /-, db1+/-, db2+/-, db3+/-, db4+/-, ckb+/-, dc0+/-, dc1+/-, dc2+/-, dc3+/-, dc4+/-, ckc+/-, dd0+/-, dd1+/-, dd2+/-, dd3+/-, dd4+/-, ckd+/- 8
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.3.2 led driver board (ta= 25 c) parameter symbol min. typ. max. unit remarks power supply voltage vddb (11.4) 12.0 (12.6) v - power supply current iddb - (4,200) tbd m vddb= 12.0v, at the maximum luminance control brti signal vbi 0 - 1.0 v high vbph 2.0 - 5.25 v brtp signal low vbpl 0 - 0.8 v high vbch 2.0 - 5.25 v brtc signal low vbcl 0 - 0.8 v high vbsh 2.0 - 5.25 v input voltage for signals pwsel signal low vbsl 0 - 0.8 v brti signal ibi tbd - tbd ? high ibph - - tbd ? brtp signal low ibpl tbd - - ? high ibch - - tbd ? brtc signal low ibcl tbd - - ? high ipsh - - tbd ? input current for signals pwsel signal 2 - low ipsl tbd - - ? 4.3.3 led driver board current wave 2 at the maximum luminance control: 100% at the minimum luminanc e control: (1)% (at f requency: 325 hz ) luminance control frequency: (255)hz (typ.) 0ma duty luminance control frequency (4,200) ma (typ.) 2 note1: luminance control frequency indicate the input pulse frequency, when select the external pulse control. see " 4.6.2 detail of brtp timing ". note2: the power supply lines (vddb and gndb) have large ripple voltage during luminance control. there is the possibility that the ripple voltage produces acoustic noise and signal wave noise in audio circuit and so on. put a capacitor (5,000 to 6,000 f) between the power supply lines (vddb and gndb) to reduce the noise, if the noise occurred in the circuit. 9
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.3.4 power supply voltage ripple 2 this product works, even if the ri pple voltage levels are beyond th e permissible values as following the table, but there might be noise on the display image. ripple voltage note1 power supply voltage unit (measure at input term inal of power supply) vdd 12.0v mvp-p 100 vddb 12.0v mvp-p 200 note1: the permissible ripple voltage includes spike noise. example of the power supply connection a) separate the power supply b) put in the filter power power vdd vddb power vdd vddb filter filter 4.3.5 fuse 2 fuse parameter 10 type supplier rating fusing current remarks 2.0a 4.0a, kamaya electric co., ltd. vdd 5 seconds maximum fcc16202ab 32v 10a note1 20 a, vddb ccf1n10 koa corporation 1 seconds maximum 60 v note1: the power supply capacity should be more than the fusing current. if it is less than the fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.4 power supply voltage sequence 4.4.1 lcd panel signal processing board t > 10ms 9.6v 0.1ms < tr < 80ms valid period 10.8v 0v vdd note1 toff > 200ms 0v vdd dip < 20ms 10.8v 10.8v lvds signals *1,*2 note2 on off on t> 10ms 0ms < t < 35ms display on screen t 450ms *1: da0+/-, da1+/-, da2+/-, da3+/-, da4+/-, cka+/-, db0+/-, db1+/-, db2+/-, db3+/-, db4+/-, ckb+/-, dc0+/-, dc1+ /-, dc2+/-, dc3+/-, dc4+/- , ckc+/-, dd0+/-, dd1+/-, dd2+/-, dd3+/-, dd4+/-, ckd+/- *2: lvds signals should be measured at the terminal of 100 resistance. note1: if there is a voltage variation (voltage drop) at the rising edge of vcc below 10.8v, there is a possibility that a product does not work due to a protection circuit. note2: lvds signals must be set to low or hi gh-impedance, except the valid period (see above sequence diagram), in order to avoid the circuitry damage. if some of signals are cut while this product is working, even if the signal input to it once again, it might not work normally. if a customer stops the display and function signals, vcc also must be shut down. note3: the backlight should be turned on within the valid period of lvds signals, in order to avoid unstable data display. 4.4.2 led driver board voltage time 0ms < t brtc tr (100) ms 12.0v ( 11.4v ) vddb 0ms < t 0v 2 note1: the backlight should be turned on within the valid period of lvds signals, in order to avoid unstable data display. note2: if tr is more than (100) ms, the backlight will be turned off by a protection circuit for led driver board. 2 note3: when vddb is 0v or brtc is low, pwsel must be set to low or open. 11
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 12 4.5 connections and functions for interface pins 4.5.1 lcd panel signal processing board cn1 socket (lcd module side): fi-re51s-hf (japan aviation electronics industry limited (jae)) adaptable plug: fi-re51hl (japan aviation electronics industry limited (jae)) pin no. symbol signal remarks 1 gnd ground 2 gnd ground 3 gnd ground note1 4 da0- 5 da0+ pixel data a0 lvds differential data input note2 6 gnd ground note1 7 da1- 8 da1+ pixel data a1 lvds differential data input note2 9 gnd ground note1 10 da2- 11 da2+ pixel data a2 lvds differential data input note2 12 gnd ground note1 13 cka- 14 cka+ pixel clock a lvds differential data input note2 15 gnd ground note1 16 da3- 17 da3+ pixel data a3 lvds differential data input note2 18 gnd ground note1 19 da4- 20 da4+ pixel data a4 lvds differential data input note2 21 gnd ground note1 22 db0- 23 db0+ pixel data b0 lvds differential data input note2 24 gnd ground note1 25 db1- 26 db1+ pixel data b1 lvds differential data input note2 27 gnd ground note1 28 db2- 29 db2+ pixel data b2 lvds differential data input note2 30 gnd ground note1 31 ckb- 32 ckb+ pixel clock b lvds differential data input note2 33 gnd ground note1 34 db3- 35 db3+ pixel data b3 lvds differential data input note2 36 gnd ground note1 37 db4- 38 db4+ pixel data b4 lvds differential data input note2 39 gnd ground note1
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 13 continued 40 gnd ground note1 41 rsev - keep this pin open. 42 rsev - keep this pin open. 43 rsev - keep this pin open. 44 rsev - keep this pin open. 45 gnd ground note1 46 gnd ground note1 47 gnd ground note1 48 rsev - keep this pin open. 49 rsev - keep this pin open. 50 rsev - keep this pin open. 51 gnd ground note1 note1: all gnd terminals should be used without any non-connected lines. note2: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 14 cn2 socket (lcd module side): fi-re41s-hf (japan aviation electronics industry limited (jae)) adaptable plug: fi-re41hl (japan aviation electronics industry limited (jae)) pin no. symbol signal remarks 1 gnd ground 2 gnd ground 3 gnd ground note1 4 dc0- 5 dc0+ pixel data c0 lvds differential data input note2 6 gnd ground note1 7 dc1- 8 dc1+ pixel data c1 lvds differential data input note2 9 gnd ground note1 10 dc2- 11 dc2+ pixel data c2 lvds differential data input note2 12 gnd ground note1 13 ckc- 14 ckc+ pixel clock c lvds differential data input note2 15 gnd ground note1 16 dc3- 17 dc3+ pixel data c3 lvds differential data input note2 18 gnd ground note1 19 dc4- 20 dc4+ pixel data c4 lvds differential data input note2 21 gnd ground note1 22 dd0- 23 dd0+ pixel data d0 lvds differential data input note2 24 gnd ground note1 25 dd1- 26 dd1+ pixel data d1 lvds differential data input note2 27 gnd ground note1 28 dd2- 29 dd2+ pixel data d2 lvds differential data input note2 30 gnd ground note1 31 ckd- 32 ckd+ pixel clock d lvds differential data input note2 33 gnd ground note1 34 dd3- 35 dd3+ pixel data d3 lvds differential data input note2 36 gnd ground note1 37 dd4- 38 dd4+ pixel data d4 lvds differential data input note2 39 gnd ground note1 40 gnd ground note1 41 gnd ground note1 note1: all gnd terminals should be used without any non-connected lines. note2: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 15 cn3 socket (lcd module side): il-z-12pl-smtye (japan aviation electronics industry limited (jae)) adaptable plug: il-z-12s-s125c (japan av iation electronics industry limited (jae)) pin no. symbol function description 1 vdd 2 vdd 3 vdd 4 vdd 5 vdd 6 vdd power supply note1 7 gnd 8 gnd 9 gnd 10 gnd 11 gnd 12 gnd signal ground note1 note1: all vdd and gnd terminal s should be used withou t any non-connected lines. 4.5.2 led driver board cn201 socket (lcd module side): df3z-10p-2h (2 ? ) (hirose electric co,.ltd.) adaptable plug: df3-10s-2c (hirose electric co,.ltd.) pin no. symbol function description 1 gndb 2 gndb 3 gndb 4 gndb 5 gndb led driver board ground note1 6 vddb 7 vddb 8 vddb 9 vddb 10 vddb power supply note1 note1: all vddb and gndb terminals should be used without any non-connected lines. cn202 socket (lcd module side): il-z-9pl-smtye (japan aviation electronics industry limited (jae)) adaptable plug: il-z-9s-s125c3 (japan aviation electronics industry limited (jae)) pin no. symbol function description 1 gndb 2 gndb led driver board ground note1 3 n.c. - keep this pin open. 4 brtc backlight on/off control signal high or open: backlight on low: backlight off 5 brth 6 brti luminance control terminal 7 brtp brtp signal note2 8 gndb led driver board ground note1 9 pwsel selection of lumi nance control signal method note2, note3 note1: all gndb terminals should be us ed without any non-connected lines. note2: see " 4.6.1 luminance control ". note3: when vddb is 0v or brtc is low, pwsel must be set to low or open.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.5.3 positions of socket 1 cn202 9 insert direction 10 cn201 1 rear side cn3 insert direction cn1 insert direction cn2 insert direction led driver board 16
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.6 luminance control 4.6.1 luminance control methods pwsel terminal brtp terminal method adjustment a nd luminance ratio ? adjustment the variable resistor ( r ) for luminance control should be 10k 5%, 1/10w. minimum point of the resist ance is the minimum luminance and maximum point of the resistan ce is the maximum luminance. the resistor ( r ) must be connected between brth-brti terminals. 17 ? luminance ratio note3 resistance luminance ratio 0 0%(min. luminance) 10 k 100% (max. luminance) variable resistor control r brti brth note1 2 high or open open ? adjustment voltage control method works, when brth terminal is 0v and vbi voltage is input between brti-brt h terminals. this control method can carry out continuation adjustment of luminance. luminance is the maximum when brti terminal is open. ? luminance ratio note3 voltage control brti voltage (vbi) luminance ratio note1 0v 0% (min. luminance) 2 1.0v 100% (max. luminance) ? adjustment pulse width modulation (pwm) method works, when pwsel terminal is low and pwm signal (brtp signal) is input into brtp terminal. the luminance is controlle d by duty ratio of brtp signal. ? luminance ratio note3 pulse width modulation low brtp signal note1 duty ratio luminance ratio note2 (0.01) (1)% (min. luminance) (at frequency: 325 hz) note4 2 1.0 100% (max. luminance) note1: in case of the variable resistor control method and the voltage control method, noises may appear on the display image depending on the input signals timing for lcd panel signal processing board. use pwm method, if interference nois es appear on the display image! note2: the led driver board will stop working, if the low period of brtp signal is more than 50ms while brtc signal is high or open. then the backlight will not turn on anymore, even if brtp signal is input again. this is not out of order. the led driver board will start to work when power is supplied again. note3: these data are the target values. note4: see " 4.6.2 detail of brtp timing ".
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.6.2 detail of brtp timing (1) timing diagrams ? outline chart 0ms tpwl 50ms 0ms tpwl 50ms 0ms tpwl 50ms brtc brtp a pwsel (low) ? detail of a part tpw tpwh tpwl vbpl vbph brtp (2) each parameter parameter symbol min. typ. max. unit remarks 18 luminance control frequency fl ( 185) - (1,000) hz note1, note2 2 external pwm pulse width tpwh (30) - - s note1, note3 2 note1: definition of para meters is as follows. fl= 1 tpw dl= tpwh tpw , note2: see the following formula for luminance control frequency. luminance control frequency= 1/tv (n+0.25) [or (n+0.75)] n = 1, 2, 3 tv: vertical cycle (see " 4.9.1 timing characteristics ".) the interference noise of lu minance control frequency a nd input signal frequency for lcd panel signal processing board m ay appear on a display. set up luminance control frequency so that the in terference noise does not appear! note3: see " 4.6.1 luminance control methods ".
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 19 4.7 method of connection for lvds transmitter transmitter pin assign dual type lvds tx cn1 bit mapping single type lvds tx thine thc63lvd1023b output connector pin no. signal name ra4 ta0 r14 - - ra5 ta1 r15 ra6 ta2 r16 ata - 4 da0- ra7 ta3 r17 ra8 ta4 r18 ata + 5 da0+ ra9 ta5 r19 ga4 ta6 g14 ga5 tb0 g15 - - ga6 tb1 g16 ga7 tb2 g17 at b - 7 da1- ga8 tb3 g18 ga9 tb4 g19 at b + 8 da1+ ba4 tb5 b14 ba5 tb6 b15 ba6 tc0 b16 - - ba7 tc1 b17 ba8 tc2 b18 at c - 10 da2- ba9 tc3 b19 hsync tc4 hsync at c + 11 da2+ vsync tc5 vsync de tc6 de ra2 td0 r12 - - ra3 td1 r13 ga2 td2 g12 at d - 16 da3- ga3 td3 g13 ba2 td4 b12 at d + 17 da3+ ba3 td5 b13 n.c. td6 - ra0 te0 r10 - - ra1 te1 r11 ga0 te2 g10 19 da4- ga1 te3 g11 ba0 te4 b10 20 da4+ ba1 te5 b11 n.c. te6 - at e - at e + - - at c l k - 13 cka- odd pixel data a clk clk clk at c l k + 14 cka+ rb4 ta0 r14 - - rb5 ta1 r15 rb6 ta2 r16 bta- 22 db0- rb7 ta3 r17 rb8 ta4 r18 bta+ 23 db0+ rb9 ta5 r19 gb4 ta6 g14 gb5 tb0 g15 - - gb6 tb1 g16 gb7 tb2 g17 btb- 25 db1- gb8 tb3 g18 gb9 tb4 g19 btb+ 26 db1+ bb4 tb5 b14 bb5 tb6 b15 bb6 tc0 b16 - - bb7 tc1 b17 bb8 tc2 b18 btc- 28 db2- bb9 tc3 b19 hsync tc4 hsync btc+ 29 db2+ vsync tc5 vsync de tc6 de rb2 td0 r12 - - rb3 td1 r13 gb2 td2 g12 btd- 34 db3- gb3 td3 g13 bb2 td4 b12 btd+ 35 db3+ bb3 td5 b13 n.c. td6 - rb0 te0 r10 - - rb1 te1 r11 gb0 te2 g10 37 db4- gb1 te3 g11 bb0 te4 b10 38 db4+ bb1 te5 b11 n.c. te6 - bte- bte+ - - 31 ckb- even pixel data b clk clk clk btclk- btclk+ 32 ckb+ 2
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 20 transmitter pin assign dual type lvds tx cn2 bit mapping single type lvds tx thine thc63lvd1023b output connector pin no. signal name rc4 ta0 r14 - - rc5 ta1 r15 rc6 ta2 r16 cta- 4 dc0- rc7 ta3 r17 rc8 ta4 r18 cta+ 5 dc0+ rc9 ta5 r19 gc4 ta6 g14 gc5 tb0 g15 - - gc6 tb1 g16 gc7 tb2 g17 ctb- 7 dc1- gc8 tb3 g18 gc9 tb4 g19 ctb+ 8 dc1+ bc4 tb5 b14 bc5 tb6 b15 bc6 tc0 b16 - - bc7 tc1 b17 bc8 tc2 b18 ctc- 10 dc2- bc9 tc3 b19 hsync tc4 hsync ctc+ 11 dc2+ vsync tc5 vsync de tc6 de rc2 td0 r12 - - rc3 td1 r13 gc2 td2 g12 ctd- 16 dc3- gc3 td3 g13 bc2 td4 b12 ctd+ 17 dc3+ bc3 td5 b13 n.c. td6 - rc0 te0 r10 - - rc1 te1 r11 gc0 te2 g10 19 dc4- gc1 te3 g11 bc0 te4 b10 20 dc4+ bc1 te5 b11 n.c. te6 - cte- cte+ - - ctclk- 13 ckc- odd pixel data c clk clk clk ctclk+ 14 ckc+ rd4 ta0 r14 - - rd5 ta1 r15 rd6 ta2 r16 dta- rd7 ta3 r17 rd8 ta4 r18 dta+ 23 dd0+ rd9 ta5 r19 gd4 ta6 g14 gd5 tb0 g15 - - gd6 tb1 g16 gd7 tb2 g17 dtb- 25 dd1- gd8 tb3 g18 gd9 tb4 g19 dtb+ 26 dd1+ bd4 tb5 b14 bd5 tb6 b15 bd6 tc0 b16 - - bd7 tc1 b17 bd8 tc2 b18 dtc- 28 dd2- bd9 tc3 b19 hsync tc4 hsync dtc+ 29 dd2+ vsync tc5 vsync de tc6 de rd2 td0 r12 - - rd3 td1 r13 gd2 td2 g12 dtd- 34 dd3- gd3 td3 g13 bd2 td4 b12 dtd+ 35 dd3+ bd3 td5 b13 n.c. td6 - rd0 te0 r10 - - rd1 te1 r11 gd0 te2 g10 37 dd4- gd1 te3 g11 bd0 te4 b10 38 dd4+ bd1 te5 b11 n.c. te6 - dte- dte+ - - 31 ckd- even pixel data d clk clk clk dtclk- dtclk+ 32 ckd+ note1: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. 2
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 21 4.8 display colors and input data signals this product can display 1,073,741,8 24 colors equivalent with 1,024 gray scale in each r, g, b sub-pixel. also the relation between display colors and input data signals is as follows. data signal (0: low level, 1: high level) display colors ra9 ra8 ra7 ra6 ra5 ra4 ra3 ra2 ra1 ra0 rb9 rb8 rb7 rb6 rb5 rb4 rb3 rb2 rb1 rb0 rc9 rc8 rc7 rc6 rc5 rc4 rc3 rc2 rc1 rc0 rd9 rd8 rd7 rd6 rd5 rd4 rd3 rd2 rd1 rd0 ga9 ga8 ga7 ga6 ga5 ga4 ga3 ga2 ga1 ga0 gb9 gb8 gb7 gb6 gb5 gb4 gb3 gb2 gb1 gb0 gc9 gc8 gc7 gc6 gc5 gc4 gc3 gc2 gc1 gc0 gd9 gd8 gd7 gd6 gd5 gd4 gd3 gd2 gd1 gd0 ba9 ba8 ba7 ba6 ba5 ba4 ba3 ba2 ba1 ba0 bb9 bb8 bb7 bb6 bb5 bb4 bb3 bb2 bb1 bb0 bc9 bc8 bc7 bc6 bc5 bc4 bc3 bc2 bc1 bc0 bd9 bd8 bd7 bd6 bd5 bd4 bd3 bd2 bd1 bd0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 red 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 magent a 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 green 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 basic colors white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : : : 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red gray scale black dark bright red 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 : : : : : : 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 green gray scale black dark bright green 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 : : : : : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 blue gray scale black dark bright blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.9 input signal timings 4.9.1 timing characteristics fv=60hz parameter symbol min. typ. max. unit remarks frequency 1/ tc 60.0 65.0 66.0 mhz - 22 duty - - - clk see the data sheet of lvds transmitter. rise time, fall time - ns - 10.34 10.34 10.77 s 96,72khz(typ.) cycle th 640 672 700 clk note1 horizontal display period thd 512 clk - 15.47 16.667 17.9 ms cycle tv 1547 1612 1628 h 60.0hz(typ.) de vertical display period tvd 1536 h - setup time - ns - clk-de hold time - ns - see the data sheet of lvds transmitter. rise time, fall time - ns - note1: the sum of jitter and skew of horizontal period should be within 1 clk. 4.9.2 input signal timing chart tc tv th invalid invalid invalid invalid invalid invalid data (a), (b), (c), (d) thd = 512clk (fixed) tvd = 1,536h (fixed) de de clk
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.10 lvds data taransmission method ra(9:0) ga(9:0) ba(9:0) d0 (9:0) clk pixel data a rb(9:0) gb(9:0) bb(9:0) clk pixel data b rc(9:0) gc(9:0) bc(9:0) clk pixel data c rd(9:0) gd(9:0) bd(9:0) clk pixel data d d2 (9:0) d4 (9:0) d1 (9:0) d3 (9:0) d5 (9:0) d1024 (9:0) d1026 (9:0) d1028 (9:0) d1025 (9:0) d1027 (9:0) d1029 (9:0) 4.11 display positions odd pixel: ra,rc= red date even pixel: rb,rd=red date ga,gc=green date gb,gd=green date ba,bc=blue date bb,bd=blue date d (1, 1) d (2, 1) d (1025, 1) d (1026, 1) 23 ra ga ba rb gb bb rc gc bc rd gd bd 1, 1 2, 1 1023, 1 1024, 1 1025, 1 1026, 1 ? ? ? ? ? ? 2047, 1 2048, 1 1, 2 2, 2 1023, 2 1024, 2 1025, 2 1026, 2 ? ? ? ? ? ? 2047, 2 2048, 2 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 1, 1535 2, 1535 1023, 1535 1024, 1535 1025, 1535 1026, 1535 2047, 1535 2048, 1535 ? ? ? ? ? ? 1, 1536 2, 1536 1023, 1536 1024, 1536 1025, 1536 1026, 1536 2047, 1536 2048, 1536 ? ? ? ? ? ?
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 24 4.12 pixel arrangnment 1 2 2,048 1 r g b r g b ? ? ? ? ? ? ? r g b ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 1,536 r g b r g b ? ? ? ? ? ? ? r g b
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.13 optics 4.13.1 optical characteristics (note1, note2) 25 parameter condition sym bol min. typ. max. unit measuring instrument remarks white at center bm-5a or sr-3 luminance r= 0 , l= 0 , u= 0 , d= 0 l tbd 800 - cd/m 2 note3 2 white/black at center bm-5a or sr-3 note3 contrast ratio cr tbd 1,400 - - note5 r= 0 , l= 0 , u= 0 , d= 0 luminance uniformity 1023/1023 gray scale r = 0 , l = 0 , u = 0 , d = 0 lu 1023 (80) - - % bm-5a note4 or note6 sr-3 x coordinate wx (0.269) 0.299 white y coordinate wy (0.285) 0.315 (0.345) - x coordinate rx - (0.65) - - red (0.33) y coordinate ry - - - x coordinate gx - (0.29) - - note3 chromaticity note8 green (0.60) y coordinate gy - - - (0.15) x coordinate bx - - - blue (0.07) y coordinate by - - - 818/1023 gray scale color uniformity r = 0 , l = 0 , u = 0 , d = 0 u?v? - - 0.01 - sr-3 note4 note7 2 r = 0 , l = 0 , u = 0 , d = 0 color gamut c (65) (72) - % sr-3 note3 at center, against ntsc color space black to white ton - (20) (30) ms note3 response time bm-5a 2 note9 white to black toff - (20) (30) ms right 70 88 - u= 0 , d= 0 , cr 10 r left u= 0 , d= 0 , cr 10 l 70 88 - bm-5a 2 or note3 up r= 0 , l= 0 , cr 10 u 70 88 - viewing angle ez contrast note10 down 70 88 - r= 0 , l= 0 , cr 10 d note1: these are initial characteristics. note2: measurement conditions are as follows. ta= 25 c, vdd= 12.0v, vddb= 12.0v, pwm: duty 100%, display mode: qxga, horizontal cycle= 1/96.72 khz, vertical cycle= 1/60.0 hz optical characteristics are measured at lumi nance saturation 20minutes after the product works in the dark room. also measurement methods are as follows. 1 photodetector (bm-5a or sr-3) or equivalent lcd module (product) 50cm note3: product surface temperature at the maximum luminance control: topf = 32 c photodetector (ez contrast) lcd module (product) 2 note4: product surface temperature at 450cd/m 2 luminance control: topf = 30 c 2 temperature difference in display area: tbd c
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) note5: see " 4.13.2 definition of contrast ratio ". note6: see " 4.13.3 definition of luminance uniformity ". note7: see " 4.13.4 definition of color uniformity ". 2 note8: these coordinates are found on cie 1931 chromaticity diagram. note9: see " 4.13.5 definition of response times ". note10: see " 4.13.6 definition of viewing angles ". 4.13.2 definition of contrast ratio the contrast ratio is calculated by using the following formula. luminance of white screen 26 luminance of black screen 4.13.3 definition of luminance uniformity the luminance uniformity is calculated by using following formula. minimum luminance from to maximum luminance from to luminance uniformity (luxx) = contrast ratio (cr) = xx: 0, 104, 512, 816, 1023 gray scale. the luminance is measured at n ear the 9 points shown below. 204 1,024 1,843 153 768 1,382 4.13.4 definition of color uniformity 2 the color (u', v') is measured at near the 9 points shown below. 204 1,024 1,843 153 768 1,382 the color uniformity in each measuring point is calculated by using the following formula. color uniformity( u?v?)= (u? x - u? y ) 2 + (v? x - v? y ) 2 u? x , v? : u?, v? value at measuring point x. x u? y , v? y : u?, v? value at measuring point y.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 4.13.5 definition of response times response time is measured at the time when the luminance change s from "black" to "white", or "white" to "black" on the same screen point, by photo-detector. ton is the time when the luminance changes from 10% up to 90%. also toff is the time when the luminance changes from 90% down to 10% (see the following diagram.). 100% 90% 10% 0% ton toff luminance white black 4.13.6 definition of viewing angles left upper lower n ormal axis (perpendicular) u d r l 12 o?clock right 5. estimated luminance lifetime the luminance lifetime is the time from initial luminance to half-luminance. this lifetime is the estimated valu e, and is not guarantee value. estimated luminance lifetime condition unit (life time expectancy) note1, note2, note3 25 c (ambient temperature of the product) 70,000 continuous operation, pwm: duty 100% led elementary substance h 60 c (surface temperature at screen) tbd continuous operation, pwm: duty 100% note1: life time expectancy is mean time to half-luminance. note2: estimated luminance lifetime is not the value for an lcd module but the value for led elementary substance. note3: by ambient temperature, the lifetime chan ges particularly. especially, in case the product works under high temperature enviro nment, the lifetime becomes short. 27
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 6. reliability tests test item condition judgment note1 60 2 c, rh= 60%, 500hours high temperature and humidity display data is white. (operation) note2 0 3 c 1hour heat cycle 60 3 c 1hour 28 (operation) 50cycles, 4hours/cycle display data is white. note2 no display malfunctions -20 3 c30minutes 60 3 c30minutes thermal shock 100cycles, 1hour/cycle (non operation) temperature transition time is within 5 minutes. 5 to 100hz, 11.76m/s 2 1 minute/cycle vibration x, y, z directions (non operation) 10 times each directions no display malfunctions no physical damages 294m/s 2 , 11ms mechanical shock x, y, z directions (non operation) 3 times each directions 150pf, 150 , 10kv esd 9 places on a panel surface note3 (operation) 10 times each places at 1 sec interval no display malfunctions sample dust: no.15 (by jis-z8901) dust 15 seconds stir (operation) 8 times repeat at 1 hour interval note2 15kpa (equivalent to altitude 13,600m) -20 c 3 c24 hours non-operation +60 c 3 c24 hours low pressure no display malfunctions 53.3kpa (equivalent to altitude 4,850m) 0 c 3 c24 hours operation +60 c 3 c 24 hours note2 note1: display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. note2: luminance: 450cd/m 2 at luminance control. note3: see the following fi gure for discharge points { { { { { { { { {
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 7. precautions 7.1 meaning of caution signs the following caution signs have very important meaning. be sure to read "7.2 cautions" and "7.3 attentions"! ! this sign has the meaning that a customer will be injured or the product will sustain damage if the customer pr actices wrong operations. this sign has the meaning that a customer will be injured if the customer practices wrong operations. 7.2 cautions 29 ? do not shock and press the l cd panel and the backlight! ther e is a danger of breaking, because they are made of glass. (shock: equal to or no greater than 294m/s 2 and equal to or no greater than 11ms, pressure: equal to or no greater than 19.6n ( 16mm jig)) ! 7.3 attentions 7.3.1 handling of the product take hold of both ends without touching the circuit board when the product (lcd module) is picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board. do not hook nor pull cables such as lamp cable, and so on, in order to avoid any damage. when the product is put on the table tempor arily, display surface must be placed downward. when handling the product, take the measures of el ectrostatic discharge with such as earth band, ionic shower and so on, because the product may be damaged by electrostatic. the torque for product mounting screws must never exceed 0.735n ? m. higher torque might result in distortion of the bezel. and the length of product mounting screws must be 5.0mm.
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) u the product must be installed using mounting holes without undue stress such as bends or twist (see outline drawings). and do not add undue stress to any portion (such as bezel flat area). bends or twist described above and undue stress to any portion may cause display mura. recommended installing method: ideal plane "a" is defined by one mounting hole (datum point) and other mounting holes. the ideal plane "a" should be the same plane within r 0.3 mm. product mounting hole ideal plane "a" m ounting hole ( d atu m point) mountin g hole v do not press or rub on the sensit ive product surfa ce. when c l ea ni ng the pro duc t surface, wipe it with a soft dry cl ot h. w do not push or pul l t h e inter f ace c o nnec tors while the pr oduct is worki ng. x when handli ng t h e product, use of an ori g inal pr otec ti on she e t on t h e pro duc t s u rface (polar iz er) i s recom m e nded for prote c ti on of product s u rface. adhe si ve type prot ec tion she e t m a y change c o l o r or chara c teris tics of t h e po lariz e r . y usually li quid crystals don' t leak t h rough the bre a kage of glasses be cause of the s u rface te nsi o n of thi n l a y e r an d the co nstru c ti on of lcd pa nel. bu t, if y o u co nt act wi th liq ui d cry s tal by any ch an c e , ple a se wash it away with s o ap a n d water . 7 . 3.2 en vi ro nmen t p d o n o t op erat e or s t ore i n h i gh t e m p eratu r e, h i g h hum idity , d e w d ro p atm o sphere o r corrosi ve ga ses. keep the produc t in packi n g box w i t h ant i sta tic p o u c h in ro o m tem p erature to av oi d dus ts an d sunl ig ht, w h e n st orin g t h e p r odu ct. q in order to pr eve n t dew c o nde nsat io n oc curred by tem p erat ure dif f er ence , t h e pro duc t p a c k in g bo x m u st be o p e n ed after e n o u g h tim e be in g lef t un der th e e nvir onm ent of a n un pa ck i n g room . eva l uat e the st orage t i m e suf f icie ntl y beca use de w conde n sat i o n is af fec t e d b y the e nvir o n m ental tem p erature and hum idity . (recom m e nded le av in g ti m e : 6 hours o r m o re w ith t h e ori g i n al pa cki ng st ate aft e r a cust om er receives the packa g e) r d o no t opera t e in h i g h m a gnet i c fi eld . if not , c i rcu it bo ards m a y be b r oke n. s this prod uc t i s no t d e sig n e d as rad i at io n h a rden ed. 30
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 7.3.4 others 7.3.3 characteristics 31 the following items are ne ither defects nor failures. response time, luminance and color may be changed by ambient temperature. display mura, flickering, vertical streams or tiny spots may be observed depending on display patterns. do not display the fixed pattern for a long time because it may cause image sticking. use a screen saver, if the fixed pattern is displayed on the screen. the display color may be changed depending on viewing angle because of the use of condenser sheet in the backlight. optical characteristics may be change d depending on input signal timings. all gnd, gndb, vdd and vddb terminals should be used without any non-connected lines. do not disassemble a product or adjust variable resistors. pack the product with the orig inal shipping package, in order to avoid any damages during transportation, when returning the product to nlt for repairing and so on. the lcd module by itself or integrated into end product should be packed and transported with display in the vertical position. otherwise the display characteristics may be degraded. 2
NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 8. outline drawings 8.1 front view 2 2 2 2 note1: not shown tolerances of the dimensions are 0.5mm. note2: the torque for product mounting screws must never exceed 0.735n ? m. note3: the length of product mounting screws from surface of plate must be 5.0mm. note4: the values in pare ntheses are for reference. unit: mm 32
2 NL204153AC21-17 preliminary data sheet dod-pp-1266 (2nd edition) 33 unit: mm note1: not shown tolerances of the dimensions are 0.5mm. note2: the torque for product mounting screws must never exceed 0.735n ? m. note3: the length of product mounting screws from surface of plate must be 5.0mm. note4: the values in pare ntheses are for reference. 8.2 rear view
NL204153AC21-17 revision history the inside of latest specifications is revised to the clerical error an d the major improvement of previous edition. only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below. document number prepared date edition revision contents and signature 1st edition dod-pp- 1243 july 8, revision contents 2011 new issue preliminary data sheet dod-pp-1266 (2nd edition) 34 w riter prepared by t. ogawa approved by t. ogawa checked by 2nd edition dod-pp- 1266 sep 16, revision contents 2011 p5 general specifications ? luminance: 770 cd/m 2 (typ.) 800 cd/m 2 (typ.) ? signal system: thc63lvd824 thc63lvd104s ? power consumption: (54) w (typ.) (58) w (typ.) p7 mechanical specifications ? module size: tbd (max. d) mm 23.0 (max. d) mm ? weight: tbd (max.) g (2,980) (max.) g p7 absolute maximum ratings ? power supply voltage- led driver board: -0.3 to +27.0 v -0.3 to +15.0 v ? operating temperature- rear surface: (0 to + tbd) c (0 to + 60) c p8 lcd panel signal processing board ? power supply current: (700) (typ.), tbd (max.) ma (590) (typ.), (980) (max.) ma p9 led driver board ? power supply current: (5,000) (typ.) ma (4,200) (typ.) ma p9 led driver board current wave ? (5,000) ma (typ.) (4,200) ma (typ.) ? at the minimum luminance control: tbd % (1) % (at frequency: 325 hz) p10 power supply voltage ripple (addition), fuse (addition) p11 led driver board ? tr tbd ms tr (100) ms ? note2: tbd (100) ms p17 luminance c ontrol methods ? variable resistor cont rol- luminance ratio: 0 : tbd % 0 % ? voltage control- luminance ratio: 0v: tbd % 0 % ? pulse width modulation- luminance ratio : tbd, tbd % (0.01), (1) %, (at frequency: 325 hz) p18 detail of brtp timing- each parameter ? luminance control frequency: (325) (max.) hz (1,000) (max.) hz ? parameter: duty ratio external pwm pulse width p19-20 method of connection for lvds transmitter ? transmitter: thc63lvd104s thc63lvd1023b p25-26 optical characteristics ? luminance: 770 cd/m 2 (typ.) 800 cd/m 2 (typ.) ? color uniformity (addition) ? response time: ton / toff: tbd (max.) ms (30) (max.) ms ? viewing angle- measuring instrument: bm-5a (addition) ? note3: topf = tbd c topf = 32 c ? note4: topf = tbd c topf = 30 c temperature difference in display area: tbd c (addition) ? note7 (addition) ? definition of color uniformity (addition)
NL204153AC21-17 revision history document number prepared date edition revision contents and signature 2nd edition dod-pp- 1266 sep 16, revision contents 2011 p31 characteristics ? optical characteristics ?, because the lcd has co ld cathode fluorescent lamps. (elimination) p32-33 outline drawings- front view ? front view ? 7.5 7.3 (2 points), 8.9 10.1 ? display center product center ? 92, 122.3 (elimination) ? 166.79, 184.55, 290.11 (additon) ? rear view ? cover: figure is changed. approved by t. ogawa checked by signature of writer prepared by preliminary data sheet dod-pp-1266 (2nd edition) 35 t. ogawa

▲Up To Search▲

Price & Availability of NL204153AC21-17

	To Download NL204153AC21-17 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .