dc/dc converte r urb1d_xd-10w series 201 4 .03.27- a /3 page 1 of 5 mornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation 10w, ultra w ide input isolated & regulated single output dc-dc converter patent protection rohs features z efficiency up to 86% z w ide range o f input v oltage (4:1) z isolation voltage :1.5k vdc z operating temperature range: -40 to +85 z output over-voltage protection, short circuit protection z international standard pin-out z low ripple & noise z a2s (wring mounting) and a4s (35mm rail mounting) products featuring anti-reverse connection for input z meet en60950, en50155 t h e urb1d_xd-10w s erie s offe r 10w of output, w it h 4 :1 w id e inpu t v oltag e of 4 0-160vd c .i t i s s uitabl e f or 7 2 v ,9 6 v ,11 0 v s tandard inpu t o f the bus voltage,single output and 1500vdc isolation, over voltage and short-circuit protection.it offers good emc performance,mee t en60950 and en50155 standards.all models are particularly suited to railway etc.c. selection guide part no. input voltage (vdc) output efficiency (%,typ.) @fullload max. capacitive load ( f) certification nominal (range) max. output voltage (vdc) output current (ma) (max./min.) urb1d05xd-10w 4 0-160 (110) 170 5 2000/100 81 2200 ce urb1d12xd-10w 12 833/42 85 220 URB1D15XD-10W 15 667/33 85 100 urb1d24xd-10w 24 416/21 86 47 note: series with suffix "a2s" are chassis mounting, with suffix "a4s" are din-rail mounting, for example urb1d05xd-10wa2s is chassis mounting , urb1d05x d-10wa4s is din-rail mounting; absolute maximum rating without damage on the converter, but it isn't recommended; the efficiency of "a2s" and "a4s" is approx. 2% lower for the protection of inverse polarity. input specifications item operatin g conditions min. typ. max. unit in p ut im p ulse v olta g e(1sec.max.) -0.7 -- 180 vdc startin g v olta g e -- -- 40 input filter pi filter output specifications item operating conditions min. typ. max. unit output voltage accuracy -- 1 2 % line regulation full load, the input voltage is from low voltage to high voltage -- 0.2 0.5 load regulation 5%-100% load -- 0.5 1 transient recovery time 25%loadstepchange -- 500 1000 s transient response deviation -- 3 5 % temperature drift coefficient full load -- -- 0.03 %/ ripple* 20mhz bandwidth -- 15 30 mv p-p noise* -- 60 100 output over-voltage protection input voltage range 110 120 140 %vo output short circuit protection continuous, self-recovery note: * ripple and noise tested with ?parallel cable? method, please see dc-dc converter application notes for specific operation methods.
dc/dc converte r urb1d_xd-10w series 201 4 .03.27- a /3 page 2 of 5 mornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation general specifications item operating conditions min. typ. max. unit insulation voltage input-output, with the test time of 1 minute and the leak current lower than 1ma. 1500 -- -- vdc insulation resistance input-output, insulation voltage 500vdc 1000 -- -- m isolation capacitance input-ou tput, 100khz/0.1v -- 1000 -- pf operating temperature derating when operating temperature up to 71 , (see fig.1) -40 -- 85 storage temperature -55 -- 125 storage humidity non-condensing 5 -- 95 % max. operating temperature for casing within the operating temperature curve -- -- 105 pin welding resistance tempera ture welding spot is 1.5mm away from the casing, 10 seconds. -- -- 300 vibration 5-150hz, displacement range: 7.5mm, acceleration: 2g switching frequency pwm mode -- 350 -- khz mtbf mil-hdbk-217f@25 1000 -- -- k hours physical specifications casing material aluminum alloy package dimensions horizontal package 50.80*25.40*11.80 mm a2s wiring package 76.00*31.50*21.20 mm a4s rail package 76.00*31.50*25.80 mm weight horizontal package/a2s wiring package/a4s rail package 22g/44g/64g (typ.) cooling methods free air convection emc specifications emi conducted disturbance cispr22/en55022 class b (see fig.3 for recommended circuit) radiated emission cispr22/en55022 class b (see fig.3 for recommended circuit) ems electrostatic discharge iec/en61000-4-2 contact 6kv perf. criteria b radiation immunity iec/en61000-4-3 10v/m perf. criteria a eft iec/en61000-4-4 4kv perf. criteria b surge immunity iec/en61000-4-5 2kv/4kv (see fig.3 for recommended circuit) perf. criteria b conducted disturbance immunity iec/en61000-4-6 3 vr.m.s perf. criteria a immunities of voltage dip, drop and short interruption iec/en61000-4-29 0-70% perf. criteria b product characteristic curve operating temperature( ) temperature d erating cur ve output power percentage(%) safe operating area -40 0407185 120 80 60 100 120 40 20 0 fig. 1
dc/dc converte r urb1d_xd-10w series 201 4 .03.27- a /3 page 3 of 5 mornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation urb1d12xd- 10w 50 55 60 65 70 75 80 85 90 95 100 40 60 80 100 120 140 160 efficiency(%) input voltage(v) efficiency vs input voltage(full load) urb1d12xd- 10w 20 30 40 50 60 70 80 90 100 5 102030405060708090100 efficiency(%) output current percentage(%) efficiency vs output load(vin=vin-nominal) design reference 1. t ypical application all the dc/dc converters of this series are tested according to the recommended circuit (see fig. 2) before delivery. if it is required to further reduce input and output ripple, properly increase the input & output of additional capacitors cin and cout or select capacitors of low equivalent impedance provided that the capacitance is no larger than the max. capacitive load of the product. dc dc vin gnd +vo 0v cin cout fig. 2 cin cout 10 f-47 f10 f 2. emc solution-recommended circuit +vin -vin fc-c01d dc-dc converter +vo 0v +vo -vo fuse + c0 cy1 cy2 fig. 3 fc-c01d is the emc auxiliary component of our company. input voltage range: 40v-160v; fuse: choose according to customer actual input current; c0: recommend to use 100uf/200v electrolytic capacitor; it is used to suppress voltage dips, is not designed without requirement of the application; cy1\cy2:1nf /2kv. emc solution-recommended circuit pcb layout fig. 4 note: the min. distance of the bonding pads between input & output isolation capacitors (cy1/cy2) shall be 2mm. 3. t he product does not support output in parallel w ith powe r pe r liter o r hot-plug use 4. for more information please find the app lication notes on www.mornsun-power.com
dc/dc converte r urb1d_xd-10w series 201 4 .03.27- a /3 page 4 of 5 mornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation dimensions and recommended layout urb1d_xd-10wa2s wiring package
dc/dc converte r urb1d_xd-10w series 201 4 .03.27- a /3 page 5 of 5 mornsun guangzhou science & technology co., ltd. reserves the copyright and right of final interpretation urb1d_xd-10wa4s rail package note: 1. packing information please refer to 'product packing information'. the packing bag number of horizontal package : 58200035, the packing bag number of a2s/a4s package:58220022; 2. the min. load shall be no lower than 5 , or the output ripple may increase rapidly; if the product is operated under the min. required load, the product performance cannot be guaranteed to comply with all performance indexes in the manual, but the reliability of the product will not be influenced; 3. the max. capacitive load should be tested within the input voltage range and under full load conditions; 4. unless otherwise specified, data in this datasheet should be tested under the conditions of ta=25 , humidity<75% when inputting nominal voltage and outputting rated load; 5. all index testing methods in this datasheet are based on our company?s corporate standards; 6. the performance indexes of the product models listed in this datasheet are as above, but some indexes of non-standard model products will exceed the above-mentioned requirements, and please directly contact our technicians for specific information; 7. we can provide product customization service; 8. specifications of this product are subject to changes without prior notice. mornsun guangzhou science & technology co., ltd. address: no. 5, kehui st. 1, kehui development center, science ave., guangzhou science city, luogang district, guangzhou, p. r. china tel: 86-20-38601850-8801 fax: 86-20-38601272 e-mail: info@mornsun.cn
|
