doc. no : qw0905-LUY5730-PF rev. : a date : 22 - oct. - 2008 data sheet super bright rectangle type led lamps LUY5730-PF lead-free parts pb ligitek electronics co.,ltd. property of ligitek only
0.5 typ 25.0min directivity radiation note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. + - 2.54typ 1.0min part no. LUY5730-PF page 1/5 7.8 1.5max 2.5 7.1 package dimensions 2.4 ligitek electronics co.,ltd. property of ligitek only
static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. viewing angle 2 1/2 (deg) dominant wave length dnm spectral halfwidth nm part nomaterial note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. algainp LUY5730-PF yellowyellow diffused emittedlens 5951.7 15 min. 160 90 2.6150 typ. min. max. typical electrical & optical characteristics (ta=25 ) color forward voltage @ ma(v) 20 luminous intensity @20ma(mcd) * peak forward current duty 1/10@10khz reverse current @5v ir storage temperature operating temperature t opr tstg power dissipationpd i fp 10 a -40 ~ +85 -40 ~ +100 120 90 mw ma absolute maximum ratings at ta=25 parameter forward current i f symbol ratings 50 uy ma unit part no. LUY5730-PF ligitek electronics co.,ltd. property of ligitek only page2/5 electrostatic discharge esd2000 v
ambient temperature( ) fig.4 relative intensity vs. temperature r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) 500 0 0.5 550600650 ambient temperature( ) fig.5 relative intensity vs. wavelength fig.3 forward voltage vs. temperature f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z @ 2 5 -20 1.0 -40 0.8 20 060 40 1.0 0.9 1.1 1.2 0.5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 100 80-40-20 0 020 3.0 2.5 2.0 1.5 1.0 80 60 40100 ligitek electronics co.,ltd. property of ligitek only fig.2 relative intensity vs. forward current forward current(ma) 4.0 fig.1 forward current vs. forward voltage typical electro-optical characteristics curve 100 f o r w a r d c u r r e n t ( m a ) 0.1 1.0 10 1.0 forward voltage(v) 2.03.0 1000 uy chip r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a 2.0 1.5 1.0 0.5 5.0 0 1.010 3.0 2.5 page 3/5 1001000 part no. LUY5730-PF
dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to body) note: 1.wave solder should not be made more than one time. 2.you can just only select one of the soldering conditions as above. 60 seconds max 0 0 25 120 preheat 50 100 2 /sec max 260 temp( c) 5 /sec max 260 c3sec max time(sec) 150 ligitek electronics co.,ltd. property of ligitek only soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time only) distance:2mm min(from solder joint to body) 2.wave soldering profile part no. LUY5730-PF page 4/5
this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. solderability test this test intended to see soldering well performed or not. 1.t.sol=230 5 2.dwell time=5 1sec thermal shock test solder resistance test high temperature high humidity test 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. 1.t.sol=260 5 2.dwell time= 10 1sec. the purpose of this test is the resistance of the device under tropical for hours. 1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 mil-std-202:103b jis c 7021: b-11 operating life test 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. low temperature storage test high temperature storage test the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) reliability test: test itemtest condition description mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 jis c 7021: b-12 mil-std-883:1008 jis c 7021: b-10 reference standard ligitek electronics co.,ltd. property of ligitek only part no. LUY5730-PF page 5/5
|
