View MPC8572E_3121869.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2010 freescale semiconductor, inc. all rights reserved. freescale semiconductor technical data 1overview this section provides a high-level overview of the features of the MPC8572E processor. figure 1 shows the major functional units within the MPC8572E. 1.1 key features the following list provides an overview of the MPC8572E feature set: ? two high-performance 32-bit book e?enhanced cores that implement the power architecture ? technology: ? each core is identical to the core within the mpc8548 processor. ? 32-kbyte l1 instruction cache and 32-kbyte l1 data cache with parity protection. caches can be locked entirely or on a per-line basis, with separate locking for instructions and data. ? signal-processing engine (spe) apu (auxiliary processing unit). provides an extensive instruction set for vector (64-bit) integer and fractional operations. these instructions use both contents 1. overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. electrical characteristics . . . . . . . . . . . . . . . . . . . . . 10 3. power characteristics . . . . . . . . . . . . . . . . . . . . . . . . 15 4. input clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5. reset initialization . . . . . . . . . . . . . . . . . . . . . . . . . 18 6. ddr2 and ddr3 sdram controller . . . . . . . . . . . 19 7. duart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 8. ethernet: enhanced three-speed ethernet (etsec) 28 9. ethernet management interface electrical characteristics . . . . . . . . . . . . . . . . . . . . . . 50 10. local bus controller (elbc) . . . . . . . . . . . . . . . . . . 53 11. programmable interrupt controller . . . . . . . . . . . . . 65 12. jtag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 13. i 2 c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 14. gpio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 15. high-speed serial interfaces (hssi) . . . . . . . . . . . . 71 16. pci express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 17. serial rapidio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 18. package description . . . . . . . . . . . . . . . . . . . . . . . . 100 19. clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 20. thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 21. system design information . . . . . . . . . . . . . . . . . . 125 22. ordering information . . . . . . . . . . . . . . . . . . . . . . . 135 23. document revision history . . . . . . . . . . . . . . . . . . 137 MPC8572E powerquicc iii integrated processor hardware specifications document number: MPC8572Eec rev. 4, 06/2010
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 2 freescale semiconductor overview the upper and lower words of the 64-bit gprs as they are defined by the spe apu. ? embedded vector and scalar single-precision fl oating-point apus. provide an instruction set for single-precision (32-bit) floating-point instructions. ? double-precision floating-point apu. provides an instruction set for double-precision (64-bit) floating-point instructions that use the 64-bit gprs. ? 36-bit real addressing ? memory management unit (mmu). especially designed for embedded applications. supports 4-kbyte?4-gbyte page sizes. ? enhanced hardware and software debug support ? performance monitor facility that is similar to , but separate from, the MPC8572E performance monitor the e500 defines features that are not implemented on this device. it also generally defines some features that this device implements more speci fically. an understanding of these differences can be critical to ensure proper operation. ? 1 mbyte l2 cache/sram ? shared by both cores. ? flexible configuration and indi vidually configurable per core. ? full ecc support on 64-bit boundary in both cache and sram modes ? cache mode supports instruction caching, data caching, or both. ? external masters can force data to be allo cated into the cache through programmed memory ranges or special transaction types (stashing). ? 1, 2, or 4 ways can be configured for stashing only. ? eight-way set-associative cache organization (32-byte cache lines) ? supports locking entire cache or selected lines. individual line locks are set and cleared through book e instructions or by externally mastered transactions. ? global locking and flash clearing done through writes to l2 configuration registers ? instruction and data locks can be flash cleared separately. ? per-way allocation of cache region to a given processor. ? sram features include the following: ? 1, 2, 4, or 8 ways can be configured as sram. ? i/o devices access sram regions by marking transactions as snoopable (global). ? regions can reside at any ali gned location in the memory map. ? byte-accessible ecc is protected using read-modify-write transaction accesses for smaller-than-cache-line accesses. ? e500 coherency module (ecm) manages co re and intra-system transactions ? address translation and mapping unit (atmu) ? twelve local access windows define mapping within local 36-bit address space. ? inbound and outbound atmus map to larger external address spaces. ? three inbound windows plus a configuration window on pci express
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 3 overview ? four inbound windows plus a default window on serial rapidio? ? four outbound windows plus default translation for pci express ? eight outbound windows plus default translation for serial rapidio with segmentation and sub-segmentation support ? two 64-bit ddr2/ddr3 memory controllers ? programmable timing supporting ddr2 and ddr3 sdram ? 64-bit data interface per controller ? four banks of memory supported, each up to 4 gbytes, for a maximum of 16 gbytes per controller ? dram chip configurations from 64 mbits to 4 gbits with x8/x16 data ports ? full ecc support ? page mode support ? up to 32 simultaneous open pages for ddr2 or ddr3 ? contiguous or discontiguous memory mapping ? cache line, page, bank, and super-bank in terleaving between memory controllers ? read-modify-write support for rapidio atomic increment, decrement, set, and clear transactions ? sleep mode support for self-refresh sdram ? on-die termination support when using ddr2 or ddr3 ? supports auto refreshing ? on-the-fly power management using cke signal ? registered dimm support ? fast memory access through jtag port ? 1.8-v sstl_1.8 compatible i/o ? support 1.5-v operation for ddr3. the detail is tbd pending on official release of appropriate industry specifications. ? support for battery-backed main memory ? programmable interrupt controller (pic) ? programming model is compliant with the openpic architecture. ? supports 16 programmable interrupt a nd processor task priority levels ? supports 12 discrete external interrupts ? supports 4 message interrupts per processor with 32-bit messages ? supports connection of an external interr upt controller such as the 8259 programmable interrupt controller ? four global high resolution timers/counters per processor that can generate interrupts ? supports a variety of other internal interrupt sources ? supports fully nested interrupt delivery ? interrupts can be routed to external pin for external processing.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 4 freescale semiconductor overview ? interrupts can be routed to the e500 core ?s standard or critical interrupt inputs. ? interrupt summary registers allow fast identification of interrupt source. ? integrated security engine (sec) optimized to pr ocess all the algorithms associated with ipsec, ike, ssl/tls, srtp, 802.16e, and 3gpp ? four crypto-channels, each supporting multi-command descriptor chains ? dynamic assignment of crypto-execution units through an integrated controller ? buffer size of 256 bytes for each execution unit, with flow control for large data sizes ? pkeu?public key execution unit ? rsa and diffie-hellman; programmable field size up to 4096 bits ? elliptic curve cryptography with f 2 m and f(p) modes and programmable field size up to 1023 bits ? deu?data encryption standard execution unit ? des, 3des ? two key (k1, k2, k1) or three key (k1, k2, k3) ? ecb, cbc and ofb-64 modes for both des and 3des ? aesu?advanced encryption standard unit ? implements the rijndael symmetric key cipher ? ecb, cbc, ctr, ccm, gcm, cmac, ofb-128, cfb-128, and lrw modes ? 128-, 192-, and 256-bit key lengths ? afeu?arc four execution unit ? implements a stream cipher compatible with the rc4 algorithm ? 40- to 128-bit programmable key ? mdeu?message digest execution unit ? sha-1 with 160-bit message digest ? sha-2 (sha-256, sha-384, sha-512) ? md5 with 128-bit message digest ? hmac with all algorithms ? keu?kasumi execution unit ? implements f8 algorithm for encryption and f9 algorithm for integrity checking ? also supports a5/3 and gea-3 algorithms ? rng?random number generator ? xor engine for parity checking in raid storage applications ? crc execution unit ? crc-32 and crc-32c ? pattern matching engine with deflate decompression ? regular expression (regex) pattern matching ? built-in case insensitivity, wildcard support, no pattern explosion ? cross-packet pattern detection
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 5 overview ? fast pattern database compilati on and fast incremental updates ? 16000 patterns, each up to 128 bytes in length ? patterns can be split into 256 sets, each of which can contain 16 subsets ? stateful rule engine enables hardware execution of state-aware logic when a pattern is found ? useful for contextual searches, multi-pattern signatures, or for performing additional checks after a pattern is found ? capable of capturing and utilizing data from the data stream (such as length field) and using that information in subsequent pattern searches (for example, positive match only if pattern is detected within the number of bytes specified in the length field) ? 8192 stateful rules ? deflate engine ? supports decompression of deflate compression format including zlib and gzip ? can work independently or in conjunction with the pattern matching engine (that is decompressed data can be passed directly to the pattern matching e ngine without further software involvement or memory copying) ? two table lookup units (tlu) ? hardware-based lookup engine offloads table searches from e500 cores ? longest prefix match, exact match, chai ned hash, and flat data table formats ? up to 32 tables, with each table up to 16m entries ? 32-, 64-, 96-, or 128-bit keys ?two i 2 c controllers ? two-wire interface ? multiple master support ? master or slave i 2 c mode support ? on-chip digital filtering rejects spikes on the bus ? boot sequencer ? optionally loads configuration data from serial rom at reset the i 2 c interface ? can be used to initialize configuration registers and/or memory ? supports extended i 2 c addressing mode ? data integrity checked with preamble signature and crc ? duart ? two 4-wire interfaces (sin, sout, rts , cts ) ? programming model compatible with the original 16450 uart and the pc16550d ? enhanced local bus controller (elbc) ? multiplexed 32-bit address and data bus operating at up to 150-mhz ? eight chip selects support eight external slaves ? up to eight-beat burst transfers ? the 32-, 16-, and 8-bit port sizes are controlled by an on-chip memory controller.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 6 freescale semiconductor overview ? three protocol engines availabl e on a per chip select basis: ? general-purpose chip select machine (gpcm) ? three user programmable machines (upms) ? nand flash control machine (fcm) ? parity support ? default boot rom chip select with configurable bus width (8, 16, or 32 bits) ? four enhanced three-speed ethernet controllers (etsecs) ? three-speed support (10/100/1000 mbps) ? four ieee std 802.3?, 802.3u, 802.3x, 802.3z, 802.3ac, 802.3ab-compatible controllers ? support for various ethernet physical interfaces: ? 1000 mbps full-duplex ieee 802.3 gmii, ieee 802.3z tbi, rtbi, rgmii and sgmii ? 10/100 mbps full and half-duplex ieee 802.3 mii, ieee 802.3 rgmii, and rmii ? flexible configuration for multiple phy interface configurations ? tcp/ip acceleration and qos features available ? ip v4 and ip v6 header recognition on receive ? ip v4 header checksum verification and generation ? tcp and udp checksum verification and generation ? per-packet configurable acceleration ? recognition of vlan, stacked (q-in-q) vlan, 802.2, pppoe session, mpls stacks, and esp/ah ip-security headers ? supported in all fifo modes ? quality of service support: ? transmission from up to eight physical queues ? reception to up to eight physical queues ? full- and half-duplex ethernet support (1000 mbps supports only full duplex): ? ieee 802.3 full-duplex flow control (automatic pause frame generation or software-programmed pause frame generation and recognition) ? programmable maximum frame length supports jumbo frames (up to 9.6 kbytes) and ieee std 802.1? virtual local area network (vlan) tags and priority ? vlan insertion and deletion ? per-frame vlan control word or default vlan for each etsec ? extracted vlan control word passed to software separately ? retransmission following a collision ? crc generation and verification of inbound/outbound frames ? programmable ethernet preamble insertion and extraction of up to 7 bytes ? mac address recognition: ? exact match on primary and vi rtual 48-bit unicast addresses ? vrrp and hsrp support for seamless router fail-over
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 7 overview ? up to 16 exact-match mac addresses supported ? broadcast address (accept/reject) ? hash table match on up to 512 multicast addresses ? promiscuous mode ? buffer descriptors backward compatible with mpc8260 and mpc860t 10/100 ethernet programming models ? rmon statistics support ? 10-kbyte internal transmit and 2-kbyte receive fifos ? two mii management interfaces for control and status ? ability to force allocation of header information and buffer descriptors into l2 cache ? 10/100 fast ethernet controlle r (fec) management interface ? 10/100 mbps full and half-duplex ieee 802.3 mii for system management ? note: when enabled, the fec occupies etsec3 and etsec4 parallel interface signals. in such a mode, etsec3 and etsec4 are only available through sgmii interfaces. ? ocean switch fabric ? full crossbar packet switch ? reorders packets from a source based on priorities ? reorders packets to bypass blocked packets ? implements starvation avoidance algorithms ? supports packets with payloads of up to 256 bytes ? two integrated dma controllers ? four dma channels per controller ? all channels accessible by the local masters ? extended dma functions (advanced chaining and striding capability) ? misaligned transfer capability ? interrupt on completed segment, link, list, and error ? supports transfers to or from any local memory or i/o port ? selectable hardware-enforced coherency (snoop/no snoop) ? ability to start and flow control up to 4 (bot h channel 0 and 1 for each dma controller) of the 8 total dma channels from external 3-pin interface by the remote masters ? the channel 2 of dma controller 2 is only allowe d to initiate and start a dma transfer by the remote master, because only one of the 3-external pins (dma2_dreq [2]) is made available ? ability to launch dma from single write transaction ? serial rapidio interface unit ? supports rapidio interconnect specification, revision 1.2 ? both 1x and 4x lp-serial link interfaces ? long- and short-haul electricals with selectable pre-compensation ? transmission rates of 1.25, 2.5, and 3.125 gbaud (data rates of 1.0, 2.0, and 2.5 gbps) per lane
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 8 freescale semiconductor overview ? auto-detection of 1x- and 4x-mode operation during port initialization ? link initialization and synchronization ? large and small size transport information field support selectable at initialization time ? 34-bit addressing ? up to 256 bytes data payload ? all transaction flows and priorities ? atomic set/clr/inc/dec for read-modify-write operations ? generation of io_read_home and flush with data for accessing cache-coherent data at a remote memory system ? receiver-controlled flow control ? error detection, recovery, and time-out for packets and control symbols as required by the rapidio specification ? register and register bit extensions as descri bed in part viii (error management) of the rapidio specification ? hardware recovery only ? register support is not required for software-mediated error recovery. ? accept-all mode of operation for fail-over support ? support for rapidio error injection ? internal lp-serial and applica tion interface-level loopback modes ? memory and phy bist for at-speed production test ? rapidio?compliant message unit ? 4 kbytes of payload per message ? up to sixteen 256-byte segments per message ? two inbound data message structures within the inbox ? capable of receiving three letters at any mailbox ? two outbound data message structures within the outbox ? capable of sending three letters simultaneously ? single segment multicast to up to 32 devids ? chaining and direct modes in the outbox ? single inbound doorbell message structure ? facility to accept port-write messages ? three pci express controllers ? pci express 1.0a compatible ? supports x8, x4, x2, and x1 link widths (see following bullet for specific width configuration options) ? auto-detection of number of connected lanes ? selectable operation as root complex or endpoint ? both 32- and 64-bit addressing
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 9 overview ? 256-byte maximum payload size ? virtual channel 0 only ? full 64-bit decode with 36-bit wide windows ? pin multiplexing for the high-speed i/o interfaces supports one of the following configurations: ? single x8/x4/x2/x1 pci express ? dual x4/x2/x1 pci express ? single x4/x2/x1 pci express and dual x2/x1 pci express ? single 1x/4x serial rapidio and single x4/x2/x1 pci express ? power management ? supports power saving modes: doze, nap, and sleep ? employs dynamic power manage ment, that automatically minimizes power consumption of blocks when they are idle ? system performance monitor ? supports eight 32-bit counters that count the occurrence of selected events ? ability to count up to 512 counter-specific events ? supports 64 reference events that can be counted on any of the eight counters ? supports duration and quantity threshold counting ? permits counting of burst events with a programmable time between bursts ? triggering and chaining capability ? ability to generate an interrupt on overflow ? system access port ? uses jtag interface and a tap controller to access entire system memory map ? supports 32-bit accesses to configuration registers ? supports cache-line burst accesses to main memory ? supports large block (4-kbyte) uploads and downloads ? supports continuous bit streaming of en tire block for fast upload and download ? ieee std 1149.1? compatible, jtag boundary scan ? 1023 fc-pbga package
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 10 freescale semiconductor electrical characteristics figure 1 shows the MPC8572E block diagram. figure 1. MPC8572E block diagram 2 electrical characteristics this section provides the ac and dc electrical specifications for the MPC8572E. the MPC8572E is currently targeted to these specifications. some of th ese specifications are independent of the i/o cell, but are included for a more complete reference. these are not purely i/o buffer design specifications. core x8/x4/x2/x1 pci express 4x serial rapidio 10/100/1gb mii, gmii, tbi, rtbi, rgmii, serial irqs sdram ddr2/3 (nor/nand) gpio i 2 c i 2 c controller etsec serial rapidio messaging unit e500 coherency module 64b ddr2/ddr3 memory controller enhanced local bus controller programmable interrupt controller (pic) duart e500 core 1-mbyte l2 cache/ sram 4-channel dma controller 32-kbyte l1 instruction cache 32-kbyte l1 data cache ocean switch fabric serial rapidio pci express i 2 c i 2 c controller rmii, sgmii, fifo MPC8572E 10/100/1gb mii, gmii, tbi, rtbi, rgmii, etsec rmii, sgmii, fifo security engine xor engine 10/100/1gb rtbi, rgmii, etsec rmii, sgmii 10/100/1gb mii, gmii, tbi, rtbi, rgmii, etsec rmii, sgmii, fifo sdram ddr2/3 64b ddr2/ddr3 memory controller table lookup unit pattern matching engine deflate engine e500 core 32-kbyte l1 instruction cache 32-kbyte l1 data cache complex bus table lookup unit external control 4-channel dma controller external control flash fec mii
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 11 electrical characteristics 2.1 overall dc electrical characteristics this section covers the ratings, conditions, and other characteristics. 2.1.1 absolute maximum ratings table 1 provides the absolute maximum ratings. table 1. absolute maximum ratings 1 characteristic symbol range unit notes core supply voltage v dd ?0.3 to 1.21 v ? pll supply voltage av dd ?0.3 to 1.21 v ? core power supply for serdes transceivers sv dd ?0.3 to 1.21 v ? pad power supply for serdes transceivers xv dd ?0.3 to 1.21 v ? ddr sdram controller i/o supply voltage ddr2 sdram interface gv dd ?0.3 to 1.98 v ? ddr3 sdram interface ?0.3 to 1.65 ? three-speed ethernet i/o, fec management interface, mii management voltage lv dd (for etsec1 and etsec2) ?0.3 to 3.63 ?0.3 to 2.75 v2 tv dd (for etsec3 and etsec4, fec) ?0.3 to 3.63 ?0.3 to 2.75 ?2 duart, system control and power management, i 2 c, and jtag i/o voltage ov dd ?0.3 to 3.63 v ? local bus and gpio i/o voltage bv dd ?0.3 to 3.63 ?0.3 to 2.75 ?0.3 to 1.98 v? input voltage ddr2 and ddr3 sdram interface signals mv in ?0.3 to (gv dd + 0.3) v 3 ddr2 and ddr3 sdram interface reference mv ref n ?0.3 to (gv dd /2 + 0.3) v ? three-speed ethernet signals lv in tv in ?0.3 to (lv dd + 0.3) ?0.3 to (tv dd + 0.3) v3 local bus and gpio signals bv in ?0.3 to (bv dd + 0.3) ? ? duart, sysclk, system control and power management, i 2 c, and jtag signals ov in ?0.3 to (ov dd + 0.3) v 3 storage temperature range t stg ?55 to 150 c ? notes: 1. functional operating conditions are given in ta b l e 2 . absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. the 3.63v maximum is only supported when the port is configured in gmii, mii, rmii or tbi modes; otherwise the 2.75v maximum applies. see section 8.2, ?fifo, gmii, mii, tbi, rgmii, rmii, and rtbi ac timing specifications ,? for details on the recommended operating conditions per protocol. 3. (m,l,o)v in may overshoot/undershoot to a voltage and for a maximum duration as shown in figure 2 .
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 12 freescale semiconductor electrical characteristics 2.1.2 recommended operating conditions table 2 provides the recommended operating conditions for this device. note that the values shown are the recommended and tested operating conditions. proper de vice operation outside these conditions is not guaranteed. table 2. recommended operating conditions characteristic symbol recommended value unit notes core supply voltage v dd 1.1 v 55 mv v ? pll supply voltage av dd 1.1 v 55 mv v 1 core power supply for serdes transceivers sv dd 1.1 v 55 mv v ? pad power supply for serdes transceivers xv dd 1.1 v 55 mv v ? ddr sdram controller i/o supply voltage ddr2 sdram interface gv dd 1.8 v 90 mv v ? ddr3 sdram interface 1.5 v 75 mv ? three-speed ethernet i/o voltage lv dd 3.3 v 165 mv 2.5 v 125 mv v4 tv dd 3.3 v 165 mv 2.5 v 125 mv 4 duart, system control and power management, i 2 c, and jtag i/o voltage ov dd 3.3 v 165 mv v 3 local bus and gpio i/o voltage bv dd 3.3 v 165 mv 2.5 v 125 mv 1.8 v 90 mv v? input voltage ddr2 and ddr3 sdram interface signals mv in gnd to gv dd v2 ddr2 and ddr3 sdram interface reference mv ref n gv dd /2 1% v ? three-speed ethernet signals lv in tv in gnd to lv dd gnd to tv dd v4 local bus and gpio signals bv in gnd to bv dd v? local bus, duart, sysclk, serial rapidio, system control and power management, i 2 c, and jtag signals ov in gnd to ov dd v3 junction temperature range t j 0 to 105 c? notes: 1. this voltage is the input to the filter discussed in section 21.2.1, ?pll power supply filtering,? and not necessarily the voltage at the av dd pin, that may be reduced from v dd by the filter. 2. caution: mv in must not exceed gv dd by more than 0.3 v. this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 3. caution: ov in must not exceed ov dd by more than 0.3 v. this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. caution: l/tv in must not exceed l/tv dd by more than 0.3 v. this limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 13 electrical characteristics figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8572E. figure 2. overshoot/undershoot voltage for tv dd /bv dd /gv dd /lv dd /ov dd the core voltage must always be provided at nominal 1.1 v. (see table 2 for actual recommended core voltage). voltage to the processor interface i/os are provided through separate sets of supply pins and must be provided at the voltages shown in table 2 . the input voltage threshold scales with respect to the associated i/o supply voltage. tv dd , bv dd , ov dd and lv dd based receivers are simple cmos i/o circuits and satisfy appropriate lvcmos type specifications. the ddr2 and ddr3 sdram interface uses differential receivers referenced by the externally supplied mv ref n signal (nominally set to gv dd /2) as is appropriate for the sstl_1.8 electrical signali ng standard for ddr2 or 1.5-v electrical signaling for ddr3. the ddr dqs receivers cannot be operated in single-ended fashion. the complement signal must be properly driven and cannot be grounded. gnd gnd ? 0.3 v gnd ? 0.7 v not to exceed 10% t/b/g/l/ov dd + 20% t/b/g/l/ov dd t/b/g/l/ov dd + 5% of t clock 1 t clock refers to the clock period associated with the respective interface: vih vil note: for i 2 c and jtag, t clock references sysclk. for ddr, t clock references mclk. for etsec, t clock references ec_gtx_clk125. for elbc, t clock references lclk.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 14 freescale semiconductor electrical characteristics 2.1.3 output driver characteristics table 3 provides information on the characteristics of the output driver strengths. the values are preliminary estimates. 2.2 power sequencing the MPC8572E requires its power rails to be applied in a specific sequence to ensure proper device operation. these requirements are as follows for power up: 1. v dd , av dd _n , bv dd , lv dd , ov dd , sv dd_srds1 and sv dd_srds2 , tv dd , xv dd_srds1 and xv dd_srds2 2. gv dd all supplies must be at their stable values within 50 ms. items on the same line have no ordering requirement with respect to one another. items on separate lines must be ordered sequentially such that voltage rails on a previous step must reach 90% of their value before the voltage rails on the current step reach 10% of theirs. to guarantee mcke low during power-on reset, the above sequencing for gv dd is required. if there is no concern about any of the ddr signals being in an indeterminate state during power-on reset, then the sequencing for gv dd is not required. table 3. output drive capability driver type programmable output impedance ( ) supply vo l ta g e notes local bus interface utilities signals 25 35 bv dd = 3.3 v bv dd = 2.5 v 1 45(default) 45(default) 125 bv dd = 3.3 v bv dd = 2.5 v bv dd = 1.8 v ddr2 signal 18 36 (half strength mode) gv dd = 1.8 v 2 ddr3 signal 20 40 (half strength mode) gv dd = 1.5 v 2 etsec/10/100 signals 45 l/tv dd = 2.5/3.3 v ? duart, system control, jtag 45 ov dd = 3.3 v ? i2c 150 ov dd = 3.3 v ? notes: 1. the drive strength of the local bus interface is determined by the configuration of the appropriate bits in porimpscr. 2. the drive strength of the ddr2 or ddr3 interface in half-strength mode is at t j = 105 c and at gv dd (min).
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 15 power characteristics note from a system standpoint, if any of the i/o power supplies ramp prior to the vdd core supply, the i/os associated with that i/o supply may drive a logic one or zero during power-on reset, and extra current may be drawn by the device. 3 power characteristics the estimated typical power dissipation for the core complex bus (ccb) versus the core frequency for this family of powerquicc iii devices is shown in table 4 . 4 input clocks 4.1 system clock timing table 5 provides the system clock (sysclk) ac timing specifications for the MPC8572E. table 4. MPC8572E power dissipation 1 1 this reflects the MPC8572E power dissipation excluding the power dissipation from b/g/l/o/t/xv dd rails. ccb frequency core frequency typical-65 2 2 typical-65 is based on v dd = 1.1 v, t j = 65 c, running dhrystone. typical-105 3 3 typical-105 is based on v dd = 1.1 v, t j = 105 c, running dhrystone. maximum 4 4 maximum is based on v dd = 1.1 v, t j = 105 c, running a smoke test. unit 533 1067 12.3 17.8 18.5 w 533 1200 12.3 17.8 18.5 w 533 1333 16.3 22.8 24.5 w 600 1500 17.3 23.9 25.9 w notes: table 5. sysclk ac timing specifications at recommended operating conditions with ov dd of 3.3v 5% . parameter/condition symbol min typical max unit notes sysclk frequency f sysclk 33 ? 133 mhz 1 sysclk cycle time t sysclk 7.5 ? 30.3 ns ? sysclk rise and fall time t kh , t kl 0.61.01.2ns 2 sysclk duty cycle t khk /t sysclk 40 ? 60 % 3
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 16 freescale semiconductor input clocks 4.2 real time clock timing the rtc input is sampled by the platform clock (ccb clock). the output of the sampling latch is then used as an input to the counters of the pic and the timebase unit of the e500. there is no jitter specification. the minimum pulse width of the rtc signal should be greater than 2x the period of the ccb clock. that is, minimum clock high time is 2 t ccb , and minimum clock low time is 2 t ccb . there is no minimum rtc frequency; rtc may be grounded if not needed. 4.3 etsec gigabit reference clock timing table 6 provides the etsec gigabit reference clocks (ec_gtx_clk125) ac timing specifications for the MPC8572E. sysclk jitter ? ? ? +/? 150 ps 4, 5, 6 notes: 1. caution: the ccb clock to sysclk ratio and e500 core to ccb clock ratio settings must be chosen such that the resulting sysclk frequency, e500 (core) frequency, and ccb clock frequency do not exceed their respective maximum or minimum operating frequencies.refer to section 19.2, ?ccb/sysclk pll ratio ,? and section 19.3, ?e500 core pll ratio ,? for ratio settings. 2. rise and fall times for sysclk are measured at 0.6 v and 2.7 v. 3. timing is guaranteed by design and characterization. 4. this represents the total input jitter?short term and long term?and is guaranteed by design. 5. the sysclk driver?s closed loop jitter bandwidth should be <500 khz at ?20 db. the bandwidth must be set low to allow cascade-connected pll-based devices to track sysclk drivers with the specified jitter. 6. for spread spectrum clocking, guidelines are +0% to ?1% down spread at a modulation rate between 20 khz and 60 khz on sysclk. table 6. ec_gtx_clk125 ac timing specifications at recommended operating conditions with lv dd /tv dd of 3.3v 5% or 2.5v 5% parameter/condition symbol min typical max unit notes ec_gtx_clk125 frequency f g125 ?125?mhz? ec_gtx_clk125 cycle time t g125 ?8?ns? ec_gtx_clk125 rise and fall time l/tv dd =2.5v l/tv dd =3.3v t g125r , t g125f ?? 0.75 1.0 ns 1 table 5. sysclk ac timing specifications (continued) at recommended operating conditions with ov dd of 3.3v 5% . parameter/condition symbol min typical max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 17 input clocks 4.4 ddr clock timing table 7 provides the ddr clock (ddrclk) ac timing specifications for the MPC8572E. 4.5 platform to etsec fifo restrictions note the following etsec fifo mode maximum speed restrictions based on platform (ccb) frequency. for fifo gmii modes (both 8-bit and 16-bit) and 16-bit encoded fifo mode: fifo tx/rx clock frequency <= plat form clock (ccb) frequency/4.2 ec_gtx_clk125 duty cycle gmii, tbi 1000base-t for rgmii, rtbi t g125h /t g125 45 47 ? 55 53 %2, 3 notes: 1. rise and fall times for ec_gtx_clk125 are measured from 0.5v and 2.0v for l/tv dd =2.5v, and from 0.6v and 2.7v for l/tv dd =3.3v. 2. timing is guaranteed by design and characterization. 3. ec_gtx_clk125 is used to generate the gtx clock for the etsec transmitter with 2% degradation. ec_gtx_clk125 duty cycle can be loosened from 47/53% as long as the phy device can tolerate the duty cycle generated by the tsec n _gtx_clk. see section 8.2.6, ?rgmii and rtbi ac timing specifications,? for duty cycle for 10base-t and 100base-t reference clock. table 7. ddrclk ac timing specifications at recommended operating conditions with ov dd of 3.3v 5% . parameter/condition symbol min typical max unit notes ddrclk frequency f ddrclk 66 ? 100 mhz 1 ddrclk cycle time t ddrclk 10.0 ? 15.15 ns ? ddrclk rise and fall time t kh , t kl 0.6 1.0 1.2 ns 2 ddrclk duty cycle t khk /t ddrclk 40 ? 60 % 3 ddrclk jitter ? ? ? +/? 150 ps 4, 5, 6 notes: 1. caution: the ddr complex clock to ddrclk ratio settings must be chosen such that the resulting ddr complex clock frequency does not exceed the maximum or minimum operating frequencies. refer to section 19.4, ?ddr/ddrclk pll ratio ,? for ratio settings. 2. rise and fall times for ddrclk are measured at 0.6 v and 2.7 v. 3. timing is guaranteed by design and characterization. 4. this represents the total input jitter?short term and long term?and is guaranteed by design. 5. the ddrclk driver?s closed loop jitter bandwidth should be <500 khz at ?20 db. the bandwidth must be set low to allow cascade-connected pll-based devices to track ddrclk drivers with the specified jitter. 6. for spread spectrum clocking, guidelines are +0% to ?1% down spread at a modulation rate between 20 khz and 60 khz on ddrclk. table 6. ec_gtx_clk125 ac timing specifications (continued) at recommended operating conditions with lv dd /tv dd of 3.3v 5% or 2.5v 5% (continued) parameter/condition symbol min typical max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 18 freescale semiconductor reset initialization for example, if the platform (ccb) frequency is 533 mhz, the fifo tx/rx clock frequency should be no more than 127 mhz. for 8-bit encoded fifo mode: fifo tx/rx clock frequency <= plat form clock (ccb) frequency/3.2 for example, if the platform (ccb) frequency is 533 mhz, the fifo tx/rx clock frequency should be no more than 167 mhz. 4.6 other input clocks for information on the input clocks of other functional blocks of the plat form such as serdes and etsec, see the respective sections of this document. 5 reset initialization table 8 describes the ac electrical specifications for the reset initialization timing. table 9 provides the pll lock times. table 8. reset initialization timing specifications parameter/condition min max unit notes required assertion time of hreset 100 ? s2 minimum assertion time for sreset 3 ? sysclks 1 pll config input setup time with stable sysclk before hreset negation 100 ? s? input setup time for por configs (other than pll config) with respect to negation of hreset 4 ? sysclks 1 input hold time for all por configs (including pll config) with respect to negation of hreset 2 ? sysclks 1 maximum valid-to-high impedance time for actively driven por configs with respect to negation of hreset ? 5 sysclks 1 notes: 1. sysclk is the primary clock input for the MPC8572E. 2. reset assertion timing requirements for ddr3 drams may differ. table 9. pll lock times parameter/condition symbol min typical max pll lock times ? 100 s? local bus pll ? 50 s?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 19 ddr2 and ddr3 sdram controller 6 ddr2 and ddr3 sdram controller this section describes the dc and ac electri cal specifications for the ddr2 and ddr3 sdram controller interface of the MPC8572E. note that the required gv dd (typ) voltage is 1.8vor 1.5v when interfacing to ddr2 or ddr3 sdram respectively. 6.1 ddr2 and ddr3 sdram interface dc electrical characteristics table 10 provides the recommended operating conditions for the ddr sdram controller of the MPC8572E when interfacing to ddr2 sdram. table 11 provides the recommended operating conditions for the ddr sdram controller of the MPC8572E when interfacing to ddr3 sdram. table 10. ddr2 sdram interface dc electrical characteristics for gv dd (typ) = 1.8 v parameter/condition symbol min max unit notes i/o supply voltage gv dd 1.71 1.89 v 1 i/o reference voltage mv ref n 0.49 gv dd 0.51 gv dd v2 i/o termination voltage v tt mv ref n ?0.04 mv ref n + 0.04 v 3 input high voltage v ih mv ref n + 0.125 gv dd +0.3 v ? input low voltage v il ?0.3 mv ref n ? 0.125 v ? output leakage current i oz ?50 50 a4 output high current (v out = 1.420 v) i oh ?13.4 ? ma ? output low current (v out = 0.280 v) i ol 13.4 ? ma ? notes: 1. gv dd is expected to be within 50 mv of the dram gv dd at all times. 2. mv ref n is expected to be equal to 0.5 gv dd , and to track gv dd dc variations as measured at the receiver. peak-to-peak noise on mv ref n may not exceed 2% of the dc value. 3. v tt is not applied directly to the device. it is the supply to that far end signal termination is made and is expected to be equal to mv ref n . this rail should track variations in the dc level of mv ref n . 4. output leakage is measured with all outputs disabled, 0 v v out gv dd . table 11. ddr3 sdram interface dc electrical characteristics for gv dd (typ) = 1.5 v parameter/condition symbol min typical max unit i/o supply voltage gv dd 1.425 1.575 v 1 i/o reference voltage mv ref n 0.49 gv dd 0.51 gv dd v2 input high voltage v ih mv ref n + 0.100 gv dd v? input low voltage v il gnd mv ref n ? 0.100 v ?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 20 freescale semiconductor ddr2 and ddr3 sdram controller table 12 provides the ddr sdram controller interface capacitance for ddr2 and ddr3. table 13 provides the current draw characteristics for mv ref n. 6.2 ddr2 and ddr3 sdram interface ac electrical characteristics this section provides the ac electrical characteristics for the ddr sdram controller interface. the ddr controller supports both ddr2 and ddr3 memories. note that although the minimum data rate for most off-the-shelf ddr3 dimms available is 800 mhz, jedec specification does allow the ddr3 to run at the data rate as low as 606 mhz. unless otherw ise specified, the ac timing specifications described in this section for ddr3 is applicable for data rate between 606 mhz and 800 mhz, as long as the dc and output leakage current i oz ?50 50 a3 notes: 1. gv dd is expected to be within 50 mv of the dram gv dd at all times. 2. mv ref n is expected to be equal to 0.5 gv dd , and to track gv dd dc variations as measured at the receiver. peak-to-peak noise on mv ref n may not exceed 1% of the dc value. 3. output leakage is measured with all outputs disabled, 0 v v out gv dd . table 12. ddr2 and ddr3 sdram interface capacitance for gv dd (typ)=1.8 v and 1.5 v parameter/condition symbol min typical max unit input/output capacitance: dq, dqs, dqs c io 6 8 pf 1, 2 delta input/output capacitance: dq, dqs, dqs c dio ? 0.5 pf 1, 2 note: 1. this parameter is sampled. gv dd = 1.8 v 0.090 v (for ddr2), f = 1 mhz, t a = 25c, v out = gv dd /2, v out (peak-to-peak) = 0.2 v. 2. this parameter is sampled. gv dd = 1.5 v 0.075 v (for ddr3), f = 1 mhz, t a = 25c, v out = gv dd /2, v out (peak-to-peak) = 0.175 v. table 13. current draw characteristics for mv ref n parameter / condition symbol min max unit note current draw for mv ref n ddr2 sdram i mvref n ? 1500 a1 ddr3 sdram 1250 1. the voltage regulator for mv ref n must be able to supply up to 1500 a or 1250 ua current for ddr2 or ddr3 respectively. table 11. ddr3 sdram interface dc electrical characteristics for gv dd (typ) = 1.5 v (continued) parameter/condition symbol min typical max unit
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 21 ddr2 and ddr3 sdram controller ac specifications of the ddr3 memory to be used are compliant to both jedec specifications as well as the specifications and requirements described in this MPC8572E hardware specifications document. 6.2.1 ddr2 and ddr3 sdram interface input ac timing specifications table 14 , table 15 , and table 16 provide the input ac timing specifications for the ddr controller when interfacing to ddr2 and ddr3 sdram. table 14. ddr2 sdram interface input ac timing specifications for 1.8-v interface at recommended operating conditions with gv dd of 1.8 v 5% parameter symbol min max unit notes ac input low voltage >=667 mhz v ilac ?m v ref n ? 0.20 v ? <= 533 mhz ? mv ref n ? 0.25 ac input high voltage >=667 mhz v ihac mv ref n + 0.20 ? v ? ? <= 533 mhz mv ref n + 0.25 ? table 15. ddr3 sdram interface input ac timing specifications for 1.5-v interface at recommended operating conditions with gv dd of 1.5 v 5%. ddr3 data rate is between 606 mhz and 800 mhz. parameter symbol min max unit notes ac input low voltage v ilac ?m v ref n ? 0.175 v ? ac input high voltage v ihac mv ref n + 0.175 ? v ? table 16. ddr2 and ddr3 sdram interface input ac timing specifications at recommended operating conditions with gv dd of 1.8 v 5% for ddr2 or 1.5 v 5% for ddr3. parameter symbol min max unit notes controller skew for mdqs?mdq/mecc t ciskew ? ? ps 1, 2 800 mhz ? ?200 200 ? ? 667 mhz ? ?240 240 ? ? 533 mhz ? ?300 300 ? ? 400 mhz ? ?365 365 ? ? note: 1. t ciskew represents the total amount of skew consumed by the controller between mdqs[n] and any corresponding bit that is captured with mdqs[n]. this should be subtracted from the total timing budget. 2. the amount of skew that can be tolerated from mdqs to a corresponding mdq signal is called tdiskew.this can be determined by the following equation: tdiskew =+/?(t/4 ? abs(tciskew)) where t is the clock period and abs(tciskew) is the absolute value of tciskew.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 22 freescale semiconductor ddr2 and ddr3 sdram controller figure 3 shows the ddr2 and ddr3 sdram interface input timing diagram. figure 3. ddr2 and ddr3 sdram interface input timing diagram 6.2.2 ddr2 and ddr3 sdram interface output ac timing specifications table 17 contains the output ac timing targets for the ddr2 and ddr3 sdram interface. table 17. ddr2 and ddr3 sdram interface output ac timing specifications at recommended operating conditions with gv dd of 1.8 v 5% for ddr2 or 1.5 v 5% for ddr3. parameter symbol 1 min max unit notes mck[n] cycle time t mck 2.5 5 ns 2 addr/cmd output setup with respect to mck t ddkhas ns 3 800 mhz 0.917 ? 667 mhz 1.10 ? 533 mhz 1.48 ? 400 mhz 1.95 ? addr/cmd output hold with respect to mck t ddkhax ns 3 800 mhz 0.917 ? 667 mhz 1.10 ? 533 mhz 1.48 ? 400 mhz 1.95 ? mcs [n] output setup with respect to mck t ddkhcs ns 3 800 mhz 0.917 ? 667 mhz 1.10 ? 533 mhz 1.48 ? mck [n] mck[n] t mck mdq[x] mdqs[n] t diskew d1 d0 t diskew t diskew
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 23 ddr2 and ddr3 sdram controller 400 mhz t ddkhcs 1.95 ? ns 3 mcs [n] output hold with respect to mck t ddkhcx ns 3 800 mhz 0.917 ? 667 mhz 1.10 ? 533 mhz 1.48 ? 400 mhz 1.95 ? mck to mdqs skew t ddkhmh ns 4 800 mhz ?0.375 0.375 <= 667 mhz ?0.6 0.6 mdq/mecc/mdm output setup with respect to mdqs t ddkhds, t ddklds ps 5 800 mhz 375 ? 667 mhz 450 ? 533 mhz 538 ? 400 mhz 700 ? mdq/mecc/mdm output hold with respect to mdqs t ddkhdx, t ddkldx ps 5 800 mhz 375 ? 667 mhz 450 ? 533 mhz 538 ? 400 mhz 700 ? mdqs preamble start t ddkhmp ns 6 800 mhz ?0.5 t mck ? 0.375 ?0.5 t mck +0.375 <= 667 mhz ?0.5 t mck ? 0.6 ?0.5 t mck +0.6 mdqs epilogue end t ddkhme ns 6 800 mhz ?0.375 0.375 table 17. ddr2 and ddr3 sdram interface output ac timing specifications (continued) at recommended operating conditions with gv dd of 1.8 v 5% for ddr2 or 1.5 v 5% for ddr3. parameter symbol 1 min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 24 freescale semiconductor ddr2 and ddr3 sdram controller note for the addr/cmd setup and hold specifications in table 17 , it is assumed that the clock control register is set to adjust the memory clocks by 1/2 applied cycle. <= 667 mhz t ddkhme ?0.6 0.6 ns 6 note: 1. the symbols used for timing specifications follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. output hold time can be read as ddr timing (dd) from the rising or falling edge of the reference clock (kh or kl) until the output went invalid (ax or dx). for example, t ddkhas symbolizes ddr timing (dd) for the time t mck memory clock reference (k) goes from the high (h) state until outputs (a) are setup (s) or output valid time. also, t ddkldx symbolizes ddr timing (dd) for the time t mck memory clock reference (k) goes low (l) until data outputs (d) are invalid (x) or data output hold time. 2. all mck/mck referenced measurements are made from the crossing of the two signals 0.1 v. 3. addr/cmd includes all ddr sdram output signals except mck/mck , mcs , and mdq/mecc/mdm/mdqs. 4. note that t ddkhmh follows the symbol conventions described in note 1. for example, t ddkhmh describes the ddr timing (dd) from the rising edge of the mck[n] clock (kh) until the mdqs signal is valid (mh). t ddkhmh can be modified through control of the mdqs override bits (called wr_data_delay) in the timing_cfg_2 register. this typically be set to the same delay as in ddr_sdram_clk_cntl[clk_adjust]. the timing parameters listed in the table assume that these 2 parameters have been set to the same adjustment value. see the MPC8572E powerquicc? iii integrated host processor family reference manual for a description and understanding of the timing modifications enabled by use of these bits. 5. determined by maximum possible skew between a data strobe (mdqs) and any corresponding bit of data (mdq), ecc (mecc), or data mask (mdm). the data strobe should be centered inside of the data eye at the pins of the microprocessor. 6. all outputs are referenced to the rising edge of mck[n] at the pins of the microprocessor. note that t ddkhmp follows the symbol conventions described in note 1. table 17. ddr2 and ddr3 sdram interface output ac timing specifications (continued) at recommended operating conditions with gv dd of 1.8 v 5% for ddr2 or 1.5 v 5% for ddr3. parameter symbol 1 min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 25 ddr2 and ddr3 sdram controller figure 4 shows the ddr2 and ddr3 sdram interface output timing for the mck to mdqs skew measurement (tddkhmh). figure 4. timing diagram for tddkhmh figure 5 shows the ddr2 and ddr3 sdram interface output timing diagram. figure 5. ddr2 and ddr3 sdram interface output timing diagram mdqs mck[n] mck[n] tmck t ddkhmhmax) = 0.6 ns or 0.375 n s t ddkhmh(min) = ?0.6 ns or -0.375 ns mdqs addr/cmd t ddkhas ,t ddkhcs t ddkhmh t ddklds t ddkhds mdq[x] mdqs[n] mck[n] mck[n] t mck t ddkldx t ddkhdx d1 d0 t ddkhax ,t ddkhcx write a0 noop t ddkhme t ddkhmp
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 26 freescale semiconductor ddr2 and ddr3 sdram controller figure 6 provides the ac test load for the ddr2 and ddr3 controller bus. figure 6. ddr2 and ddr3 controller bus ac test load 6.2.3 ddr2 and ddr3 sdram differential timing specifications this section describes the dc and ac differential electrical specifications for the ddr2 and ddr3 sdram controller interface of the MPC8572E. note vid specifies the input differential voltage |vtr -vcp| required for switching, where vtr is the true input signal (such as mck or mdqs) and vcp is the complementary input signal (such as mck or mdqs ). table 18 provides the differential specifications for the MPC8572E differential signals mdqs/mdqs and mck/mck when in ddr2 mode. table 18. ddr2 sdram differential electrical characteristics parameter/condition symbol min max unit notes dc input signal voltage v in ?0.3 gv dd + 0.3 v ? dc differential input voltage v id ??m v? ac differential input voltage v idac ??m v? dc differential output voltage v oh ??m v? ac differential output voltage v ohac jedec: 0.5 jedec: gv dd + 0.6 v ? ac differential cross-point voltage v ixac ??m v? input midpoint voltage v mp ??m v? output z 0 = 50 r l = 50 gv dd /2 v tr v cp gnd gvdd v mp v id or v od v ix or v ox v in
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 27 duart table 19 provides the differential specifications for the MPC8572E differential signals mdqs/mdqs and mck/mck when in ddr3 mode. 7duart this section describes the dc and ac electri cal specifications for the duart interface of the MPC8572E. 7.1 duart dc electrical characteristics table 20 provides the dc electrical characteristics for the duart interface. table 19. ddr3 sdram differential electrical characteristics parameter/condition symbol min max unit notes dc input signal voltage v in ??mv? dc differential input voltage v id ??mv? ac differential input voltage v idac ??mv? dc differential output voltage v oh ??mv? ac differential output voltage v ohac ??mv? ac differential cross-point voltage v ixac ??mv? input midpoint voltage v mp ??mv? table 20. duart dc electrical characteristics parameter symbol min max unit supply voltage (3.3 v) ov dd 3.13 3.47 v high-level input voltage v ih 2ov dd + 0.3 v low-level input voltage v il ?0.3 0.8 v input current (v in 1 = 0 v or v in = v dd) i in ? 5 a high-level output voltage (ov dd = min, i oh = ?2 ma) v oh 2.4 ? v low-level output voltage (ov dd = min, i ol = 2 ma) v ol ?0 . 4 v note: 1. note that the symbol v in , in this case, represents the ov in symbol referenced in ta ble 1 .
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 28 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) 7.2 duart ac electrical specifications table 21 provides the ac timing parameters for the duart interface. 8 ethernet: enhanced three-speed ethernet (etsec) this section provides the ac and dc electrical char acteristics for the enhanced three-speed ethernet controller. 8.1 enhanced three-speed ethernet controller (etsec) (10/100/1000 mbps)?fifo/gmii/mii/tbi/rgmii/rtbi/rmii electrical characteristics the electrical characteristics specified here apply to all fifo mode, gigabit media independent interface (gmii), media independent interface (mii), ten-bit interface (tbi), reduced gigabit media independent interface (rgmii), reduced ten-bit interface (rtbi), and reduced media independent interface (rmii) signals except management data input/output (mdio) and manage ment data clock (mdc), and serial gigabit media independent interface (sgmii). the rgmii, rtbi and fifo mode interfaces are defined for 2.5 v, while the gmii, mii, rmii, and tbi interfaces can operate at both 2.5v and 3.3v. the gmii, mii, or tbi interface timing is compliant with ieee 802.3. the rgmii and rtbi interfaces follow the reduced gigabit media-independent interface (rgmii) specification version 1.3 (12/10/2000). the rmii interface follows the rmii consortium rmii specification version 1.2 (3/20/1998). the electrical characteristics for mdio and mdc are specified in section 9, ?ethernet management interface electrical characteristics.? the electrical characteristics for sgmii is specified in section 8.3, ?sgmii interface electrical characteristics .? the sgmii interface conforms (with ex ceptions) to the serial-gmii specification version 1.8. table 21. duart ac timing specifications at recommended operating conditions with ov dd of 3.3v 5%. parameter value unit notes minimum baud rate f ccb /1,048,576 baud 1, 2 maximum baud rate f ccb /16 baud 1, 2, 3 oversample rate 16 ? 1, 4 notes: 1. guaranteed by design 2. f ccb refers to the internal platform clock frequency. 3. actual attainable baud rate is limited by the latency of interrupt processing. 4. the middle of a start bit is detected as the 8 th sampled 0 after the 1-to-0 transition of the start bit. subsequent bit values are sampled each 16 th sample.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 29 ethernet: enhanced three-speed ethernet (etsec) the fast ethernet controller (fec) operates in mi i mode only, and complies with the ac and dc electrical characteristics specified in this chapter for mii. note that if fec is used, etsec 3 and 4 are only available in sgmii mode. 8.1.1 etsec dc electrical characteristics all mii, gmii, rmii, and tbi drivers and receivers co mply with the dc parametric attributes specified in table 22 and table 23 . all rgmii, rtbi and fifo drivers and receivers comply with the dc parametric attributes specified in table 23 . the rgmii and rtbi signals are based on a 2.5-v cmos interface voltage as defined by jedec eia/jesd8-5. table 22. gmii, mii, rmii, and tbi dc electrical characteristics parameter symbol min max unit notes supply voltage 3.3 v lv dd tv dd 3.13 3.47 v 1, 2 1 lv dd supports etsecs 1 and 2. 2 tv dd supports etsecs 3 and 4 or fec. output high voltage (lv dd /tv dd = min, ioh = ?4.0 ma) voh 2.40 lv dd /tv dd + 0.3 v ? output low voltage (lv dd /tv dd = min, iol = 4.0 ma) vol gnd 0.50 v ? input high voltage v ih 2.0 lv dd /tv dd + 0.3 v ? input low voltage v il ?0.3 0.90 v ? input high current (v in = lv dd , v in = tv dd ) i ih ?4 0 a 1, 2,3 3 the symbol v in , in this case, represents the lv in and tv in symbols referenced in ta ble 1 . input low current (v in = gnd) i il ?600 ? a 3 notes: table 23. mii, gmii, rmii, rgmii, tbi, rtbi, and fifo dc electrical characteristics parameters symbol min max unit notes supply voltage 2.5 v lv dd/ tv dd 2.37 2.63 v 1,2 output high voltage (lv dd /tv dd = min, ioh = ?1.0 ma) v oh 2.00 lv dd /tv dd + 0.3 v ? output low voltage (lv dd /tv dd = min, i ol = 1.0 ma) v ol gnd ? 0.3 0.40 v ? input high voltage v ih 1.70 lv dd /tv dd + 0.3 v ? input low voltage v il ?0.3 0.70 v ?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 30 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) 8.2 fifo, gmii, mii, tbi, rgmii, rmii, and rtbi ac timing specifications the ac timing specifications for fifo, gmii, mii, tbi, rgmii, rmii and rtbi are presented in this section. 8.2.1 fifo ac specifications the basis for the ac specifications for the etsec?s fifo modes is the double data rate rgmii and rtbi specifications, because they have similar performance and are described in a source-synchronous fashion like fifo modes. however, the fifo interface provide s deliberate skew between the transmitted data and source clock in gmii fashion. when the etsec is configured for fifo modes, all clocks are supplied from external sources to the relevant etsec interface. that is, the transmit clock must be applied to the etsec n ?s tsec n _tx_clk, while the receive clock must be applied to pin tsec n _rx_clk. the etsec internally uses the transmit clock to synchronously generate tr ansmit data and outputs an echoed copy of the transmit clock back on the tsec n _gtx_clk pin (while transmit data appears on tsec n _txd[7:0], for example). it is intended that external receivers capture etsec transmit data using the clock on tsec n _gtx_clk as a source- synchronous timing reference. typically, the clock edge that launched the data can be used, because the clock is delayed by the etsec to allow acceptable set-up margin at the receiver. note that there is a relationship between the maximum fifo speed and the platform (ccb) frequency. for more information see section 4.5, ?platform to etsec fifo restrictions . ? table 24 and table 25 summarize the fifo ac specifications. input high current (v in = lv dd , v in = tv dd ) i ih ?1 0 a 1, 2,3 input low current (v in = gnd) i il ?15 ? a 3 note: 1 lv dd supports etsecs 1 and 2. 2 tv dd supports etsecs 3 and 4 or fec. 3 note that the symbol v in , in this case, represents the lv in and tv in symbols referenced in ta b l e 1 . table 24. fifo mode transmit ac timing specification at recommended operating conditions with lv dd /tv dd of 2.5v 5% parameter/condition symbol min typ max unit tx_clk, gtx_clk clock period 1 t fit 5.3 8.0 100 ns tx_clk, gtx_clk duty cycle t fith /t fit 45 50 55 % tx_clk, gtx_clk peak-to-peak jitter t fitj ??250ps table 23. mii, gmii, rmii, rgmii, tbi, rtbi, and fifo dc electrical characteristics (continued) parameters symbol min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 31 ethernet: enhanced three-speed ethernet (etsec) figure 7 and figure 8 show the fifo timing diagrams. figure 7. fifo transmit ac timing diagram rise time tx_clk (20%?80%) t fitr ? ? 0.75 ns fall time tx_clk (80%?20%) t fitf ? ? 0.75 ns fifo data txd[7:0], tx_er, tx_en setup time to gtx_clk t fitdv 2.0 ? ? ns gtx_clk to fifo data txd[7:0], tx_er, tx_en hold time t fitdx 0.5 ? 3.0 ns notes: 1. the minimum cycle period (or maximum frequency) of the tx_clk is dependent on the maximum platform frequency of the speed bins the part belongs to as well as the fifo mode under operation. refer to section 4.5, ?platform to etsec fifo restrictions ,? for more detailed description. table 25. fifo mode receive ac timing specification at recommended operating conditions with lv dd /tv dd of 2.5v 5% parameter/condition symbol min typ max unit rx_clk clock period 1 t fir 5.3 8.0 100 ns rx_clk duty cycle t firh /t fir 45 50 55 % rx_clk peak-to-peak jitter t firj ? ? 250 ps rise time rx_clk (20%?80%) t firr ? ? 0.75 ns fall time rx_clk (80%?20%) t firf ? ? 0.75 ns rxd[7:0], rx_dv, rx_er setup time to rx_clk t firdv 1.5 ? ? ns rxd[7:0], rx_dv, rx_er hold time to rx_clk t firdx 0.5 ? ? ns 1. the minimum cycle period (or maximum frequency) of the rx_clk is dependent on the maximum platform frequency of the speed bins the part belongs to as well as the fifo mode under operation. refer to section 4.5, ?platform to etsec fifo restrictions ,? for more detailed description. table 24. fifo mode transmit ac timing specification (continued) at recommended operating conditions with lv dd /tv dd of 2.5v 5% parameter/condition symbol min typ max unit t fit t fith t fitf t fitdx txd[7:0] tx_en gtx_clk tx_er t fitdv t fitr
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 32 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 8. fifo receive ac timing diagram 8.2.2 gmii ac timing specifications this section describes the gmii transmit and receive ac timing specifications. 8.2.2.1 gmii transmit ac timing specifications table 26 provides the gmii transmit ac timing specifications. table 26. gmii transmit ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit gmii data txd[7:0], tx_er, tx_en setup time t gtkhdv 2.5??ns gtx_clk to gmii data txd[7:0], tx_er, tx_en delay t gtkhdx 0.5 ? 5.0 ns gtx_clk data clock rise time (20%-80%) t gtxr 2 ??1.0ns gtx_clk data clock fall time (80%-20%) t gtxf 2 ??1.0ns notes: 1. the symbols used for timing specifications herein follow the pattern t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t gtkhdv symbolizes gmii transmit timing (gt) with respect to the t gtx clock reference (k) going to the high state (h) relative to the time date input signals (d) reaching the valid state (v) to state or setup time. also, t gtkhdx symbolizes gmii transmit timing (gt) with respect to the t gtx clock reference (k) going to the high state (h) relative to the time date input signals (d) going invalid (x) or hold time. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for example, the subscript of t gtx represents the gmii(g) transmit (tx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. guaranteed by design. t fir t firh t firf t firr rx_clk rxd[7:0] rx_dv rx_er valid data t firdx t firdv
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 33 ethernet: enhanced three-speed ethernet (etsec) figure 9 shows the gmii transmit ac timing diagram. figure 9. gmii transmit ac timing diagram 8.2.2.2 gmii receive ac timing specifications table 27 provides the gmii receive ac timing specifications. figure 10 provides the ac test load for etsec. figure 10. etsec ac test load table 27. gmii receive ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit rx_clk clock period t grx ?8.0? ns rx_clk duty cycle t grxh /t grx 40 ? 60 ns rxd[7:0], rx_dv, rx_er setup time to rx_clk t grdvkh 2.0 ? ? ns rxd[7:0], rx_dv, rx_er hold time to rx_clk t grdxkh 0??ns rx_clk clock rise (20%-80%) t grxr 2 ??1.0ns rx_clk clock fall time (80%-20%) t grxf 2 ??1.0ns note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t grdvkh symbolizes gmii receive timing (gr) with respect to the time data input signals (d) reaching the valid state (v) relative to the t rx clock reference (k) going to the high state (h) or setup time. also, t grdxkl symbolizes gmii receive timing (gr) with respect to the time data input signals (d) went invalid (x) relative to the t grx clock reference (k) going to the low (l) state or hold time. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particul ar functional. for example, the subscript of t grx represents the gmii (g) receive (rx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. guaranteed by design. gtx_clk txd[7:0] t gtkhdx t gtx t gtxh t gtxr t gtxf tg tkhdv tx_en tx_er output lv dd /2 r l = 50 z 0 = 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 34 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 11 shows the gmii receive ac timing diagram. figure 11. gmii receive ac timing diagram 8.2.3 mii ac timing specifications this section describes the mii transmit and receive ac timing specifications. 8.2.3.1 mii transmit ac timing specifications table 28 provides the mii transmit ac timing specifications. table 28. mii transmit ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit tx_clk clock period 10 mbps t mtx 2 ? 400 ? ns tx_clk clock period 100 mbps t mtx ?40?ns tx_clk duty cycle t mtxh/ t mtx 35 ? 65 % tx_clk to mii data txd[3:0], tx_er, tx_en delay t mtkhdx 1 5 15 ns tx_clk data clock rise (20%-80%) t mtxr 2 1.0 ? 4.0 ns tx_clk data clock fall (80%-20%) t mtxf 2 1.0 ? 4.0 ns notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t mtkhdx symbolizes mii transmit timing (mt) for the time t mtx clock reference (k) going high (h) until data outputs (d) are invalid (x). note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. for example, the subscript of t mtx represents the mii(m) transmit (tx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. guaranteed by design. rx_clk rxd[7:0] t grdxkh t grx t grxh t grxr t grxf t grdvkh rx_dv rx_er
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 35 ethernet: enhanced three-speed ethernet (etsec) figure 12 shows the mii transmit ac timing diagram. figure 12. mii transmit ac timing diagram 8.2.3.2 mii receive ac timing specifications table 29 provides the mii receive ac timing specifications. figure 13 provides the ac test load for etsec. figure 13. etsec ac test load table 29. mii receive ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit rx_clk clock period 10 mbps t mrx 2 ? 400 ? ns rx_clk clock period 100 mbps t mrx ?4 0?n s rx_clk duty cycle t mrxh /t mrx 35 ? 65 % rxd[3:0], rx_dv, rx_er setup time to rx_clk t mrdvkh 10.0 ? ? ns rxd[3:0], rx_dv, rx_er hold time to rx_clk t mrdxkh 10.0 ? ? ns rx_clk clock rise (20%-80%) t mrxr 2 1.0 ? 4.0 ns rx_clk clock fall time (80%-20%) t mrxf 2 1.0 ? 4.0 ns notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t mrdvkh symbolizes mii receive timing (mr) with respect to the time data input signals (d) reach the valid state (v) relative to the t mrx clock reference (k) going to the high (h) state or setup time. also, t mrdxkl symbolizes mii receive timing (gr) with respect to the time data input signals (d) went invalid (x) relative to the t mrx clock reference (k) going to the low (l) state or hold time. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for example, the subscript of t mrx represents the mii (m) receive (rx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. guaranteed by design. tx_clk txd[3:0] t mtkhdx t mtx t mtxh t mtxr t mtxf tx_en tx_er output z 0 = 50 lv dd /2 r l = 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 36 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 14 shows the mii receive ac timing diagram. figure 14. mii receive ac timing diagram 8.2.4 tbi ac timing specifications this section describes the tbi trans mit and receive ac timing specifications. 8.2.4.1 tbi transmit ac timing specifications table 30 provides the tbi transmit ac timing specifications. table 30. tbi transmit ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit tcg[9:0] setup time gtx_clk going high t ttkhdv 2.0??ns tcg[9:0] hold time from gtx_clk going high t ttkhdx 1.0??ns gtx_clk rise (20%?80%) t ttxr 2 ??1.0ns gtx_clk fall time (80%?20%) t ttxf 2 ??1.0ns notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state )(reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t ttkhdv symbolizes the tbi transmit timing (tt) with respect to the time from t ttx (k) going high (h) until the referenced data signals (d) reach the valid state (v) or setup time. also, t ttkhdx symbolizes the tbi transmit timing (tt) with respect to the time from t ttx (k) going high (h) until the referenced data signals (d) reach the invalid state (x) or hold time. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for example, the subscript of t ttx represents the tbi (t) transmit (tx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. guaranteed by design. rx_clk rxd[3:0] t mrdxkl t mrx t mrxh t mrxr t mrxf rx_dv rx_er t mrdvkh valid data
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 37 ethernet: enhanced three-speed ethernet (etsec) figure 15 shows the tbi transmit ac timing diagram. figure 15. tbi transmit ac timing diagram 8.2.4.2 tbi receive ac timing specifications table 31 provides the tbi receive ac timing specifications. table 31. tbi receive ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition 3 symbol 1 min typ max unit clock period for tbi receive clock 0, 1 t trx ? 16.0 ? ns skew for tbi receive clock 0, 1 t sktrx 7.5 ? 8.5 ns duty cycle for tbi receive clock 0, 1 t trxh /t trx 40 ? 60 % rcg[9:0] setup time to rising edge of tbi receive clock 0, 1 t trdvkh 2.5 ? ? ns rcg[9:0] hold time to rising edge of tbi receive clock 0, 1 t trdxkh 1.5 ? ? ns clock rise time (20%-80%) for tbi receive clock 0, 1 t trxr 2 0.7 ? 2.4 ns clock fall time (80%-20%) for tbi receive clock 0, 1 t trxf 2 0.7 ? 2.4 ns notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t trdvkh symbolizes tbi receive timing (tr) with respect to the time data input signals (d) reach the valid state (v) relative to the t trx clock reference (k) going to the high (h) state or setup time. also, t trdxkh symbolizes tbi receive timing (tr) with respect to the time data input signals (d) went invalid (x) relative to the t trx clock reference (k) going to the high (h) state. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for example, the subscript o f t trx represents the tbi (t) receive (rx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). for symbols representing skews, the subscript is skew (sk) followed by the clock that is being skewed (tr x). 2. guaranteed by design. 3. the signals ?tbi receive clock 0? and ?tbi receive clock 1? refer to tsecn_rx_clk and tsecn_tx_clk pins respectively. these two clock signals are also referred as pma_rx_clk[0:1]. gtx_clk tcg[9:0] t ttxr t ttx t ttxh t ttxr t ttxf t ttkhdv t ttkhdx t ttxf
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 38 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 16 shows the tbi receive ac timing diagram. figure 16. tbi receive ac timing diagram 8.2.5 tbi single-clock mode ac specifications when the etsec is configured for tbi modes, all cloc ks are supplied from external sources to the relevant etsec interface. in single-clock tbi mode, when a 125-mhz tbi receive clock is supplied on tsec n pin (no receive clock is used in this mode, whereas for the dual-clock mode this is the pma1 receive clock). the 125-mhz transmit clock is applied in all tbi modes. a summary of the single-clock tbi mode ac specifications for receive appears in table 32 . table 32. tbi single-clock mode receive ac timing specification at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol min typ max unit rx_clk clock period t trrx 7.5 8.0 8.5 ns rx_clk duty cycle t trrh /t trrx 40 50 60 % rx_clk peak-to-peak jitter t trrj ? ? 250 ps rise time rx_clk (20%?80%) t trrr ??1.0ns fall time rx_clk (80%?20%) t trrf ??1.0ns rcg[9:0] setup time to rx_clk rising edge t trrdvkh 2.0 ? ? ns rcg[9:0] hold time to rx_clk rising edge t trrdxkh 1.0 ? ? ns tbi receive clock 1 rcg[9:0] t trx t trxh t trxr t trxf t trdvkh tbi receive clock 0 t trdxkh t trdvkh t trdxkh t sktrx t trxh valid data valid data (tsec n _tx_clk) (tsec n _rx_clk)
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 39 ethernet: enhanced three-speed ethernet (etsec) figure 17 shows the tbi receive the timing diagram. figure 17. tbi single-clock mode receive ac timing diagram 8.2.6 rgmii and rtbi ac timing specifications table 33 presents the rgmii and rtbi ac timing specifications. table 33. rgmii and rtbi ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5 v 5%. parameter/condition symbol 1 min typ max unit data to clock output skew (at transmitter) t skrgt ?500 0 500 ps data to clock input skew (at receiver) 2 t skrgt 1.0 ? 2.8 ns clock period 3 t rgt 7.2 8.0 8.8 ns duty cycle for 10base-t and 100base-tx 3, 4 t rgth /t rgt 40 50 60 % rise time (20%?80%) t rgtr ? ? 0.75 ns fall time (20%?80%) t rgtf ? ? 0.75 ns notes: 1. note that, in general, the clock reference symbol representation for this section is based on the symbols rgt to represent rgmii and rtbi timing. for example, the subscript of t rgt represents the tbi (t) receive (rx) clock. note also that the notation for rise (r) and fall (f) times follows the clock symbol that is being represented. for symbols representing skews, th e subscript is skew (sk) followed by the clock that is being skewed (rgt). 2. this implies that pc board design requires clocks to be routed such that an additional trace delay of greater than 1.5 ns will be added to the associated clock signal. 3. for 10 and 100 mbps, t rgt scales to 400 ns 40 ns and 40 ns 4 ns, respectively. 4. duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three t rgt of the lowest speed transitioned between. t trr t trrh t trrf t trrr rx_clk rcg[9:0] valid data t trrdx t trrdv
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 40 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 18 shows the rgmii and rtbi ac timing and multiplexing diagrams. figure 18. rgmii and rtbi ac timing and multiplexing diagrams 8.2.7 rmii ac timing specifications this section describes the rmii transmit and receive ac timing specifications. 8.2.7.1 rmii transmit ac timing specifications table 34 shows the rmii transmit ac timing specifications. table 34. rmii transmit ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit tsecn_tx_clk clock period t rmt 15.0 20.0 25.0 ns tsecn_tx_clk duty cycle t rmth 35 50 65 % tsecn_tx_clk peak-to-peak jitter t rmtj ? ? 250 ps rise time tsecn_tx_clk (20%?80%) t rmtr 1.0 ? 2.0 ns fall time tsecn_tx_clk (80%?20%) t rmtf 1.0 ? 2.0 ns gtx_clk t rgt t rgth t skrgt tx_ctl txd[8:5] txd[7:4] txd[9] txerr txd[4] txen txd[3:0] (at transmitter) txd[8:5][3:0] txd[7:4][3:0] tx_clk (at phy) rx_ctl rxd[8:5] rxd[7:4] rxd[9] rxerr rxd[4] rxdv rxd[3:0] rxd[8:5][3:0] rxd[7:4][3:0] rx_clk (at phy) t skrgt t skrgt t skrgt
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 41 ethernet: enhanced three-speed ethernet (etsec) figure 19 shows the rmii transmit ac timing diagram. figure 19. rmii transmit ac timing diagram 8.2.7.2 rmii receive ac timing specifications table 35 shows the rmii receive ac timing specifications. tsecn_tx_clk to rmii data txd[1:0], tx_en delay t rmtdx 1.0 ? 10.0 ns note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t mtkhdx symbolizes mii transmit timing (mt) for the time t mtx clock reference (k) going high (h) until data outputs (d) are invalid (x). note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. for example, the subscript of t mtx represents the mii(m) transmit (tx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). table 35. rmii receive ac timing specifications at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit tsecn_tx_clk clock period t rmr 15.0 20.0 25.0 ns tsecn_tx_clk duty cycle t rmrh 35 50 65 % tsecn_tx_clk peak-to-peak jitter t rmrj ??2 5 0p s rise time tsecn_tx_clk (20%?80%) t rmrr 1.0 ? 2.0 ns fall time tsecn_tx_clk (80%?20%) t rmrf 1.0 ? 2.0 ns rxd[1:0], crs_dv, rx_er setup time to tsecn_tx_clk rising edge t rmrdv 4.0 ? ? ns table 34. rmii transmit ac timing specifications (continued) at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit tsec n _tx_clk txd[1:0] t rmtdx t rmt t rmth t rmtr t rmtf tx_en tx_er
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 42 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 20 provides the ac test load for etsec. figure 20. etsec ac test load figure 21 shows the rmii receive ac timing diagram. figure 21. rmii receive ac timing diagram 8.3 sgmii interface electrical characteristics each sgmii port features a 4-wire ac-coupled seri al link from the dedicated serdes 2 interface of MPC8572E as shown in figure 22 , where c tx is the external (on board) ac-coupled capacitor. each output pin of the serdes transmitter differential pair features 50- output impedance. each input of the serdes receiver differential pair features 50- on-die termination to sgnd_srds2 (xcorevss). the reference circuit of the serdes transmitter and receiver is shown in figure 54 . when an etsec port is configured to operate in sgmii mode, the parallel interface?s output signals of this etsec port can be left floating. the input si gnals should be terminated based on the guidelines described in section 21.5, ?connection recommendations,? as long as such termination does not violate the desired por configuration require ment on these pins, if applicable. rxd[1:0], crs_dv, rx_er hold time to tsecn_tx_clk rising edge t rmrdx 2.0 ? ? ns note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t mrdvkh symbolizes mii receive timing (mr) with respect to the time data input signals (d) reach the valid state (v) relative to the t mrx clock reference (k) going to the high (h) state or setup time. also, t mrdxkl symbolizes mii receive timing (gr) with respect to the time data input signals (d) went invalid (x) relative to the t mrx clock reference (k) going to the low (l) state or hold time. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for example, the subscript of t mrx represents the mii (m) receive (rx) clock. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). table 35. rmii receive ac timing specifications (continued) at recommended operating conditions with lv dd /tv dd of 2.5/ 3.3 v 5%. parameter/condition symbol 1 min typ max unit output z 0 = 50 lv dd /2 r l = 50 tsec n _tx_clk rxd[1:0] t rmrdx t rmr t rmrh t rmrr t rmrf crs_dv rx_er t rmrdv valid data
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 43 ethernet: enhanced three-speed ethernet (etsec) when operating in sgmii mode, the etsec ec_gtx_clk125 clock is not required for this port. instead, serdes reference clock is required on sd2_ref_clk and sd2_ref_clk pins. 8.3.1 dc requirements for sgmii sd2_ref_clk and sd2_ref_clk the characteristics and dc requirements of the separate serdes reference clock are described in section 15, ?high-speed serial interfaces (hssi).? 8.3.2 ac requirements for sgmii sd2_ref_clk and sd2_ref_clk table 36 lists the sgmii serdes reference clock ac requirements. note that sd2_ref_clk and sd2_ref_clk are not intended to be used with, and shoul d not be clocked by, a spread spectrum clock source. table 36. sd2_ref_clk and sd2_ref_clk ac requirements symbol parameter description min typical max units notes t ref refclk cycle time ? 10 (8) ? ns 1 t refcj refclk cycle-to-cycle jitter. difference in the period of any two adjacent refclk cycles ??100ps ? t refpj phase jitter. deviation in edge location with respect to mean edge location ?50 ? 50 ps ? note: 1. 8 ns applies only when 125 mhz serdes2 reference clock frequency is selected through cfg_srds_sgmii_refclk during por.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 44 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) 8.3.3 sgmii transmitter and receiver dc electrical characteristics table 37 and table 38 describe the sgmii serdes transmitter and receiver ac-coupled dc electrical characteristics. transmitter dc characteristics are measured at the transmitte r outputs (sd2_tx[n] and sd2_tx [n]) as depicted in figure 23 . table 37. sgmii dc transmitter electrical characteristics parameter symbol min typ max unit notes supply voltage xv dd_srds2 1.045 1.1 1.155 v ? output high voltage voh ? ? xv dd_srds2-typ /2 + |v od | -max /2 mv 1 output low voltage vol xv dd_srds2-typ /2 - |v od | -max /2 ??m v1 output ringing v ring ??1 0%? output differential voltage 2, 3, 5 |v od | 359 550 791 mv equalization setting: 1.0x 329 505 725 equalization setting: 1.09x 299 458 659 equalization setting: 1.2x 270 414 594 equalization setting: 1.33x 239 367 527 equalization setting: 1.5x 210 322 462 equalization setting: 1.71x 180 275 395 equalization setting: 2.0x output offset voltage v os 473 550 628 mv 1, 4 output impedance (single-ended) r o 40 ? 60 ? mismatch in a pair r o ??1 0%? change in v od between ?0? and ?1? |v od |? ? 2 5m v?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 45 ethernet: enhanced three-speed ethernet (etsec) figure 22. 4-wire ac-coupled sgmii serial link connection example change in v os between ?0? and ?1? v os ??2 5m v? output current on short to gnd i sa , i sb ??4 0m a? note: 1. this will not align to dc-coupled sgmii. xv dd_srds2-typ =1.1 v. 2. |v od | = |v sd2_txn - v sd2_tx n |. |v od | is also referred as output differential peak voltage. v tx-diffp-p = 2*|v od | . 3. the |v od | value shown in the table assumes the following transmit equalization setting in the xmiteq ab (for serdes 2 lanes a & b) or xmiteq ef (for serdes 2 lanes e & e) bit field of MPC8572E?s serdes 2 control register: ?the msbit (bit 0) of the above bit field is set to zero (selecting the full v dd-diff-p-p amplitude - power up default); ?the lsbits (bit [1:3]) of the above bit field is set based on the equalization setting shown in table. 4. v os is also referred to as output common mode voltage. ? 5.the |v od | value shown in the typ column is based on the condition of xv dd_srds2-typ =1.1v, no common mode offset variation (v os =550mv), serdes2 transmitter is terminated with 100- differential load between sd2_tx[n] and sd2_tx [n]. table 37. sgmii dc transmitter electrical characteristics (continued) parameter symbol min typ max unit notes MPC8572E sgmii serdes interface 50 50 transmitter sd2_txn sd_rxm sd2_tx n sd_rx m receiver c tx c tx 50 50 sd2_rxn sd2_rx n receiver transmitter sd_txm sd_tx m c tx c tx 50 50 50 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 46 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 23. sgmii transmitter dc measurement circuit table 38 lists the sgmii dc receiver elecetrical characteristics. table 38. sgmii dc receiver electrical characteristics parameter symbol min typ max unit notes supply voltage xv dd_srds2 1.045 1.1 1.155 v ? dc input voltage range ? n/a ? 1 input differential voltage lsts = 0 v rx_diffp-p 100 ? 1200 mv 2, 4 lsts = 1 175 ? loss of signal threshold lsts = 0 vlos 30 ? 100 mv 3, 4 lsts = 1 65 ? 175 input ac common mode voltage v cm_acp-p ?100 mv 5 receiver differential input impedance z rx_diff 80 100 120 ? receiver common mode input impedance z rx_cm 20 ? 35 ? common mode input voltage v cm ?v xcorevss ?v6 note: 1. input must be externally ac-coupled. 2. v rx_diffp-p is also referred to as peak to peak input differential voltage 3. the concept of this parameter is equivalent to the electrical idle detect threshold parameter in pci express. refer to pci express differential receiver (rx) input specifications section for further explanation. 4. the lsts shown in the table refers to the lsts ab or lsts ef bit field of MPC8572E?s serdes 2 control register. 5. v cm_acp-p is also referred to as peak to peak ac common mode voltage. 6. on-chip termination to sgnd_srds2 (xcorevss). 50 transmitter sd2_txn sd2_tx n 50 v os v od MPC8572E sgmii serdes interface 50 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 47 ethernet: enhanced three-speed ethernet (etsec) 8.3.4 sgmii ac timing specifications this section describes the sgmii transmit and receive ac timing specifications. transmitter and receiver characteristics are measured at the transmitter outputs (sd2_tx[n] and sd2_tx [n]) or at the receiver inputs (sd2_rx[n] and sd2_rx [n]) as depicted in figure 25 , respectively. 8.3.4.1 sgmii transmit ac timing specifications table 39 provides the sgmii transmit ac timing targets. a source synchronous clock is not provided. 8.3.4.2 sgmii receive ac timing specifications table 40 provides the sgmii receive ac timing specifications. source synchronous clocking is not supported. clock is recovered from the data. figure 24 shows the sgmii receiver input compliance mask eye diagram. table 39. sgmii transmit ac timing specifications at recommended operating conditions with xv dd_srds2 = 1.1v 5%. parameter symbol min typ max unit notes deterministic jitter jd ? ? 0.17 ui p-p ? total jitter jt ? ? 0.35 ui p-p ? unit interval ui 799.92 800 800.08 ps 1 v od fall time (80%-20%) tfall 50 ? 120 ps ? v od rise time (20%-80%) t rise 50 ? 120 ps ? notes: 1. each ui is 800 ps 100 ppm. table 40. sgmii receive ac timing specifications at recommended operating conditions with xv dd_srds2 = 1.1v 5%. parameter symbol min typ max unit notes deterministic jitter tolerance jd 0.37 ? ? ui p-p 1 combined deterministic and random jitter tolerance jdr 0.55 ? ? ui p-p 1 sinusoidal jitter tolerance jsin 0.1 ? ? ui p-p 1 total jitter tolerance jt 0.65 ? ? ui p-p 1 bit error ratio ber ? ? 10 -12 ?? unit interval ui 799.92 800 800.08 ps 2 ac coupling capacitor c tx 5 ? 200 nf 3 notes: 1. measured at receiver. 2. each ui is 800 ps 100 ppm. 3. the external ac coupling capacitor is required. it is recommended to be placed near the device transmitter outputs. 4. refer to rapidio ? 1x/4x lp serial physical layer specification for interpretation of jitter specifications.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 48 freescale semiconductor ethernet: enhanced three-speed ethernet (etsec) figure 24. sgmii receiver input compliance mask figure 25. sgmii ac test/measurement load time (ui) receiver differential input voltage 0 0.275 0.4 0.6 0.725 ? v rx_diffp-p-min /2 v rx_diffp-p-min /2 ? v rx_diffp-p-max /2 v rx_diffp-p-max /2 0 1
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 49 ethernet: enhanced three-speed ethernet (etsec) 8.4 etsec ieee std 1588? ac specifications figure 26 shows the data and command output timing diagram. figure 26. etsec ieee 1588 output ac timing 1 the output delay is count starting rising edge if t t1588clkout is non-inverting. otherwise, it is count starting falling edge. figure 27 shows the data and command input timing diagram. figure 27. etsec ieee 1588 input ac timing table 41 provides the ieee 1588 ac timing specifications. table 41. etsec ieee 1588 ac timing specifications at recommended operating conditions with lv dd /tv dd of 3.3 v 5% or 2.5 v 5% parameter/condition symbol min typ max unit note tsec_1588_clk clock period t t1588clk 3.3 ? t tx_clk *9 ns 1 tsec_1588_clk duty cycle t t1588clkh /t t1588clk 40 50 60 % ? tsec_1588_clk peak-to-peak jitter t t1588clkinj ??2 5 0p s? rise time etsec_1588_clk (20%?80%) t t1588clkinr 1.0 ? 2.0 ns ? fall time etsec_1588_clk (80%?20%) t t1588clkinf 1.0 ? 2.0 ns ? tsec_1588_clk_out clock period t t1588clkout 2*t t1588clk ??ns? tsec_1588_clk_out tsec_1588_pulse_out tsec_1588_trig_out t t1588ov t t1588clkout t t1588clkouth tsec_1588_clk tsec_1588_trig_in t t1588trigh t t1588clk t t1588clkh
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 50 freescale semiconductor ethernet management interface electrical characteristics 9 ethernet management interface electrical characteristics the electrical characteristics specified here apply to mii management interface signals ecn_mdio (management data input/output) and ecn_mdc (management data clock). the electrical characteristics for gmii, sgmii, rgmii, rmii, tbi and rtbi are specified in ? section 8, ?ethernet: enhanced three-speed ethernet (etsec).? 9.1 mii management dc electrical characteristics the ecn_mdc and ecn_mdio are defined to operate at a supply voltage of 3.3 v or 2.5 v. the dc electrical characteristics for ecn_mdio and ecn_mdc are provided in table 42 and table 43 . tsec_1588_clk_out duty cycle t t1588clkoth /t t1588clkout 30 50 70 % ? tsec_1588_pulse_out t t1588ov 0.5 ? 3.0 ns ? tsec_1588_trig_in pulse width t t1588trigh 2*t t1588clk_max ??ns2 note: 1.when tmr_ctrl[cksel] is set as ?00?, the external tsec_1588_clk input is selected as the 1588 timer reference clock source, with the timing defined in table 41 , ?etsec ieee 1588 ac timing specifications.? the maximum value of t t1588clk is defined in terms of t tx_clk , that is the maximum clock cycle period of the equivalent interface speed that the etsec1 port is running at. when etsec1 is configured to operate in the parallel mode, the t tx_clk is the maximum clock period of the tsec1_tx_clk. when etsec1 operates in sgmii mode, the maximum value of t t1588clk is defined in terms of the recovered clock from sgmii serdes. for example, for sgmii 10/100/1000 mbps modes, the maximum value of t t1588clk is 3600, 360, 72 ns respectively. see the MPC8572E powerquicc? iii integrated communications processor reference manual for detailed description of tmr_ctrl registers. 2. it needs to be at least two times of the clock period of the clock selected by tmr_ctrl[cksel]. table 42. mii management dc electrical characteristics(lv dd /tv dd =3.3 v) parameter symbol min max unit notes supply voltage (3.3 v) lv dd /tv dd 3.13 3.47 v 1, 2 output high voltage (lv dd /tv dd = min, i oh = ?1.0 ma) v oh 2.10 ov dd + 0.3 v ? output low voltage (lv dd /tv dd =min, i ol = 1.0 ma) v ol gnd 0.50 v ? input high voltage v ih 2.0 ? v ? input low voltage v il ?0 . 9 0v? input high current (lv dd /tv dd = max, v in 3 = 2.1 v) i ih ?4 0 a? table 41. etsec ieee 1588 ac timing specifications (continued) at recommended operating conditions with lv dd /tv dd of 3.3 v 5% or 2.5 v 5% parameter/condition symbol min typ max unit note
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 51 ethernet management interface electrical characteristics 9.2 mii management ac electrical specifications table 44 provides the mii management ac timing specifications.there are three sets of ethernet management signals (ec1_mdc and ec1_mdi o, ec3_mdc and ec3_mdio, ec5_mdc and ec5_mdio). these are not explicitly shown in the table or in the figure following. input low current (lv dd /tv dd = max, v in = 0.5 v) i il ?600 ? a? note: 1. ec1_mdc and ec1_mdio operate on lv dd . 2. ec3_mdc & ec3_mdio and ec5_mdc & ec5_mdio operate on tv dd . 3. note that the symbol v in , in this case, represents the lv in and tv in symbol referenced in tab le 1 . table 43. mii management dc electrical characteristics (lv dd /tv dd =2.5 v) parameters symbol min max unit notes supply voltage 2.5 v lv dd/ tv dd 2.37 2.63 v 1,2 1 ec1_mdc and ec1_mdio operate on lv dd . 2 ec3_mdc & ec3_mdio and ec5_mdc & ec5_mdio operate on tv dd . output high voltage (lv dd /tv dd = min, ioh = ?1.0 ma) v oh 2.00 lv dd /tv dd + 0.3 v ? output low voltage (lv dd /tv dd = min, i ol = 1.0 ma) v ol gnd ? 0.3 0.40 v ? input high voltage v ih 1.70 lv dd /tv dd + 0.3 v ? input low voltage v il ?0.3 0.70 v ? input high current (v in = lv dd , v in = tv dd ) i ih ?1 0 a 1, 2,3 3 note that the symbol v in , in this case, represents the lv in and tv in symbols referenced in ta b l e 1 . input low current (v in = gnd) i il ?15 ? a 3 note: table 44. mii management ac timing specifications at recommended operating conditions with lv dd /tv dd of 3.3 v 5% or 2.5 v 5%. parameter/condition symbol 1 min typ max unit notes ecn_mdc frequency f mdc 0.9 2.5 9.3 mhz 2, 3 ecn_mdc period t mdc 107.5 ? 1120 ns ? ecn_mdc clock pulse width high t mdch 32 ? ? ns ? ecn_mdc to ecn_mdio delay t mdkhdx 10 ? 16*t plb_clk ns 5 ecn_mdio to ecn_mdc setup time t mddvkh 5??n s? table 42. mii management dc electrical characteristics(lv dd /tv dd =3.3 v) (continued) parameter symbol min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 52 freescale semiconductor ethernet management interface electrical characteristics figure 28 shows the mii management ac timing diagram. figure 28. mii management interface timing diagram ecn_mdio to ecn_mdc hold time t mddxkh 0??n s? ecn_mdc rise time t mdcr ? ? 10 ns 4 ecn_mdc fall time t mdhf ? ? 10 ns 4 notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t mdkhdx symbolizes management data timing (md) for the time t mdc from clock reference (k) high (h) until data outputs (d) are invalid (x) or data hold time. also, t mddvkh symbolizes management data timing (md) with respect to the time data input signals (d) reach the valid state (v) relative to the t mdc clock reference (k) going to the high (h) state or setup time. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 2. this parameter is dependent on the etsec system clock speed, which is half of the platform frequency (f ccb ). the actual ecn_mdc output clock frequency for a specific etsec port can be programmed by configuring the mgmtclk bit field of MPC8572E?s miimcfg register, based on the platform (ccb) clock running for the device. the formula is: platform frequency (ccb)/(2*frequency divider determined by miicfg[mgmtclk] encoding selection). for example, if miicfg[mgmtclk] = 000 and the platform (ccb) is currently running at 533 mhz, f mdc = 533/(2*4*8) = 533/64 = 8.3 mhz. that is, for a system running at a particular platform frequency (f ccb ), the ecn_mdc output clock frequency can be programmed between maximum f mdc = f ccb /64 and minimum f mdc = f ccb /448. refer to MPC8572E reference manual?s miimcfg register section for more detail. 3. the maximum ecn_mdc output clock frequency is defined based on the maximum platform frequency for MPC8572E (600 mhz) divided by 64, while the minimum ecn_mdc output clock frequency is defined based on the minimum platform frequency for MPC8572E (400 mhz) divided by 448, following the formula described in note 2 above. the typical ecn_mdc output clock frequency of 2.5 mhz is shown for reference purpose per ieee 802.3 specification. 4. guaranteed by design. 5. t plb_clk is the platform (ccb) clock. table 44. mii management ac timing specifications (continued) at recommended operating conditions with lv dd /tv dd of 3.3 v 5% or 2.5 v 5%. parameter/condition symbol 1 min typ max unit notes ecn_mdc t mddxkh t mdc t mdch t mdcr t mdcf t mddvkh t mdkhdx ecn_mdio ecn_mdio (input) (output)
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 53 local bus controller (elbc) 10 local bus controller (elbc) this section describes the dc and ac electrical specifications for the local bus interface of the MPC8572E. 10.1 local bus dc electrical characteristics table 45 provides the dc electrical characteristics for the local bus interface operating at bv dd = 3.3 v dc. table 46 provides the dc electrical characteristics for the local bus interface operating at bv dd = 2.5 v dc. table 45. local bus dc electrical characteristics (3.3 v dc) parameter symbol min max unit supply voltage 3.3v bv dd 3.13 3.47 v high-level input voltage v ih 2b v dd + 0.3 v low-level input voltage v il ?0.3 0.8 v input current (bv in 1 = 0 v or bv in = bv dd ) i in ? 5 a high-level output voltage (bv dd = min, i oh = ?2 ma) v oh bv dd ? 0.2 ? v low-level output voltage (bv dd = min, i ol = 2 ma) v ol ?0 . 2 v note: 1. note that the symbol bv in , in this case, represents the bv in symbol referenced in ta ble 1 . table 46. local bus dc electrical characteristics (2.5 v dc) parameter symbol min max unit supply voltage 2.5v bv dd 2.37 2.63 v high-level input voltage v ih 1.70 bv dd + 0.3 v low-level input voltage v il ?0.3 0.7 v input current (bv in 1 = 0 v or bv in = bv dd ) i ih ?1 0 a i il ?15 high-level output voltage (bv dd = min, i oh = ?1 ma) v oh 2.0 bv dd + 0.3 v low-level output voltage (bv dd = min, i ol = 1 ma) v ol gnd ? 0.3 0.4 v note: 1. the symbol bv in , in this case, represents the bv in symbol referenced in ta b l e 1 .
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 54 freescale semiconductor local bus controller (elbc) table 47 provides the dc electrical characteristics for the local bus interface operating at bv dd = 1.8 v dc. 10.2 local bus ac electrical specifications table 48 describes the general timing parameters of the local bus interface at bv dd = 3.3 v dc. table 47. local bus dc electrical characteristics (1.8 v dc) parameter symbol min max unit supply voltage 1.8v bv dd 1.71 1.89 v high-level input voltage v ih 0.65 x bv dd bv dd + 0.3 v low-level input voltage v il ?0.3 0.35 x bv dd v input current (bv in 1 = 0 v or bv in = bv dd ) i in tbd tbd a high-level output voltage (i oh = ?100 a) v oh bv dd ? 0.2 ? v high-level output voltage (i oh = ?2 ma) v oh bv dd ? 0.45 ? v low-level output voltage (i ol = 100 a) v ol ?0 . 2 v low-level output voltage (i ol = 2 ma) v ol ?0 . 4 5 v note: 1. the symbol bv in , in this case, represents the bv in symbol referenced in ta ble 1 . table 48. local bus general timing parameters (bv dd = 3.3 v dc)?pll enabled at recommended operating conditions with bv dd of 3.3 v 5%. parameter symbol 1 min max unit notes local bus cycle time t lbk 6.67 12 ns 2 local bus duty cycle t lbkh/ t lbk 43 57 % ? lclk[n] skew to lclk[m] or lsync_out t lbkskew ? 150 ps 7,8 input setup to local bus clock (except lgta /lupwait) t lbivkh1 1.8 ? ns 3, 4 lgta /lupwait input setup to local bus clock t lbivkh2 1.7 ? ns 3, 4 input hold from local bus clock (except lgta /lupwait) t lbixkh1 1.0 ? ns 3, 4 lgta /lupwait input hold from local bus clock t lbixkh2 1.0 ? ns 3, 4 lale output negation to high impedance for lad/ldp (latch hold time) t lbotot 1.5 ? ns 6 local bus clock to output valid (except lad/ldp and lale) t lbkhov1 ?2.3ns? local bus clock to data valid for lad/ldp t lbkhov2 ?2.4ns3 local bus clock to address valid for lad t lbkhov3 ?2.3ns3 local bus clock to lale assertion t lbkhov4 ?2.3ns3
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 55 local bus controller (elbc) table 49 describes the general timing parameters of the local bus interface at bv dd = 2.5 v dc. output hold from local bus clock (except lad/ldp and lale) t lbkhox1 0.7 ? ns 3 output hold from local bus clock for lad/ldp t lbkhox2 0.7 ? ns 3 local bus clock to output high impedance (except lad/ldp and lale) t lbkhoz1 ?2.5ns5 local bus clock to output high impedance for lad/ldp t lbkhoz2 ?2.5ns5 note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t lbixkh1 symbolizes local bus timing (lb) for the input (i) to go invalid (x) with respect to the time the t lbk clock reference (k) goes high (h), in this case for clock one(1). also, t lbkhox symbolizes local bus timing (lb) for the t lbk clock reference (k) to go high (h), with respect to the output (o) going invalid (x) or output hold time. 2. all timings are in reference to lsync_in for pll enabled and internal local bus clock for pll bypass mode. 3. all signals are measured from bv dd /2 of the rising edge of lsync_in for pll enabled or internal local bus clock for pll bypass mode to 0.4 bv dd of the signal in question for 3.3-v signaling levels. 4. input timings are measured at the pin. 5. for purposes of active/float timing measurements, the hi-z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. t lbotot is a measurement of the minimum time between the negation of lale and any change in lad. t lbotot is programmed with the lbcr[ahd] parameter. 7. maximum possible clock skew between a clock lclk[m] and a relative clock lclk[n]. skew measured between complementary signals at bv dd /2. 8. guaranteed by design. table 49. local bus general timing parameters (bv dd = 2.5 v dc)?pll enabled at recommended operating conditions with bv dd of 2.5 v 5% parameter symbol 1 min max unit notes local bus cycle time t lbk 6.67 12 ns 2 local bus duty cycle t lbkh/ t lbk 43 57 % ? lclk[n] skew to lclk[m] or lsync_out t lbkskew ? 150 ps 7, 8 input setup to local bus clock (except lgta /lupwait) t lbivkh1 1.9 ? ns 3, 4 lgta /lupwait input setup to local bus clock t lbivkh2 1.8 ? ns 3, 4 input hold from local bus clock (except lgta /lupwait) t lbixkh1 1.1 ? ns 3, 4 lgta /lupwait input hold from local bus clock t lbixkh2 1.1 ? ns 3, 4 lale output negation to high impedance for lad/ldp (latch hold time) t lbotot 1.5 ? ns 6 local bus clock to output valid (except lad/ldp and lale) t lbkhov1 ?2.4ns? table 48. local bus general timing parameters (bv dd = 3.3 v dc)?pll enabled (continued) at recommended operating conditions with bv dd of 3.3 v 5%. (continued) parameter symbol 1 min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 56 freescale semiconductor local bus controller (elbc) table 50 describes the general timing parameters of the local bus interface at bv dd = 1.8 v dc local bus clock to data valid for lad/ldp t lbkhov2 ?2.5ns3 local bus clock to address valid for lad t lbkhov3 ?2.4ns3 local bus clock to lale assertion t lbkhov4 ?2.4ns3 output hold from local bus clock (except lad/ldp and lale) t lbkhox1 0.8 ? ns 3 output hold from local bus clock for lad/ldp t lbkhox2 0.8 ? ns 3 local bus clock to output high impedance (except lad/ldp and lale) t lbkhoz1 ?2.6ns5 local bus clock to output high impedance for lad/ldp t lbkhoz2 ?2.6ns5 note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t lbixkh1 symbolizes local bus timing (lb) for the input (i) to go invalid (x) with respect to the time the t lbk clock reference (k) goes high (h), in this case for clock one(1). also, t lbkhox symbolizes local bus timing (lb) for the t lbk clock reference (k) to go high (h), with respect to the output (o) going invalid (x) or output hold time. 2. all timings are in reference to lsync_in for pll enabled and internal local bus clock for pll bypass mode. 3. all signals are measured from bv dd /2 of the rising edge of lsync_in for pll enabled or internal local bus clock for pll bypass mode to 0.4 bv dd of the signal in question for 2.5-v signaling levels. 4. input timings are measured at the pin. 5. for purposes of active/float timing measurements, the hi-z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. t lbotot is a measurement of the minimum time between the negation of lale and any change in lad. t lbotot is programmed with the lbcr[ahd] parameter. 7. maximum possible clock skew between a clock lclk[m] and a relative clock lclk[n]. skew measured between complementary signals at bv dd /2. 8. guaranteed by design. table 50. local bus general timing parameters (bv dd = 1.8 v dc)?pll enabled at recommended operating conditions with bv dd of 1.8 v 5% parameter symbol 1 min max unit notes local bus cycle time t lbk 6.67 12 ns 2 local bus duty cycle t lbkh/ t lbk 43 57 % ? lclk[n] skew to lclk[m] or lsync_out t lbkskew ? 150 ps 7, 8 input setup to local bus clock (except lgta /lupwait) t lbivkh1 2.4 ? ns 3, 4 lgta /lupwait input setup to local bus clock t lbivkh2 1.9 ? ns 3, 4 input hold from local bus clock (except lgta /lupwait) t lbixkh1 1.1 ? ns 3, 4 lgta /lupwait input hold from local bus clock t lbixkh2 1.1 ? ns 3, 4 lale output negation to high impedance for lad/ldp (latch hold time) t lbotot 1.2 ? ns 6 table 49. local bus general timing parameters (bv dd = 2.5 v dc)?pll enabled (continued) at recommended operating conditions with bv dd of 2.5 v 5% (continued) parameter symbol 1 min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 57 local bus controller (elbc) figure 29 provides the ac test load for the local bus. figure 29. local bus ac test load local bus clock to output valid (except lad/ldp and lale) t lbkhov1 ?3.2ns? local bus clock to data valid for lad/ldp t lbkhov2 ?3.2ns3 local bus clock to address valid for lad t lbkhov3 ?3.2ns3 local bus clock to lale assertion t lbkhov4 ?3.2ns3 output hold from local bus clock (except lad/ldp and lale) t lbkhox1 0.9 ? ns 3 output hold from local bus clock for lad/ldp t lbkhox2 0.9 ? ns 3 local bus clock to output high impedance (except lad/ldp and lale) t lbkhoz1 ?2.6ns5 local bus clock to output high impedance for lad/ldp t lbkhoz2 ?2.6ns5 note: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t lbixkh1 symbolizes local bus timing (lb) for the input (i) to go invalid (x) with respect to the time the t lbk clock reference (k) goes high (h), in this case for clock one(1). also, t lbkhox symbolizes local bus timing (lb) for the t lbk clock reference (k) to go high (h), with respect to the output (o) going invalid (x) or output hold time. 2. all timings are in reference to lsync_in for pll enabled and internal local bus clock for pll bypass mode. 3. all signals are measured from bv dd /2 of the rising edge of lsync_in for pll enabled or internal local bus clock for pll bypass mode to 0.4 bv dd of the signal in question for 1.8-v signaling levels. 4. input timings are measured at the pin. 5. for purposes of active/float timing measurements, the hi-z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. t lbotot is a measurement of the minimum time between the negation of lale and any change in lad. t lbotot is programmed with the lbcr[ahd] parameter. 7. maximum possible clock skew between a clock lclk[m] and a relative clock lclk[n]. skew measured between complementary signals at bv dd /2. 8. guaranteed by design. table 50. local bus general timing parameters (bv dd = 1.8 v dc)?pll enabled (continued) at recommended operating conditions with bv dd of 1.8 v 5% (continued) parameter symbol 1 min max unit notes output z 0 = 50 bv dd /2 r l = 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 58 freescale semiconductor local bus controller (elbc) figure 30 through figure 35 show the local bus signals. figure 30. local bus signals, non-special signals only (pll enabled) table 51 describes the general timing parameters of the local bus interface at bv dd = 3.3 v dc with pll disabled. table 51. local bus general timing parameters?pll bypassed at recommended operating conditions with bv dd of 3.3 v 5% parameter symbol 1 min max unit notes local bus cycle time t lbk 12 ? ns 2 local bus duty cycle t lbkh/ t lbk 43 57 % ? internal launch/capture clock to lclk delay t lbkhkt 2.3 4.0 ns ? input setup to local bus clock (except lgta /lupwait) t lbivkh1 5.8 ? ns 4, 5 lgta /lupwait input setup to local bus clock t lbivkl2 5.7 ? ns 4, 5 input hold from local bus clock (except lgta /lupwait) t lbixkh1 -1.3 ? ns 4, 5 lgta /lupwait input hold from local bus clock t lbixkl2 -1.3 ? ns 4, 5 output signals: la[27:31]/lcs [0:7]/lwe [0:3]/ lfwe /lbctl/lfcle/ lfale /loe /lfre /lfwp t lbkhov1 t lbkhov2 t lbkhov3 lsync_in input signals: lad[0:31]/ldp[0:3] output (data) signals: lad[0:31]/ldp[0:3] output (address) signal: lad[0:31] lale t lbixkh1 t lbivkh1 t lbivkh2 t lbixkh2 t lbkhox1 t lbkhoz1 t lbkhox2 t lbkhoz2 input signal: lgta/ lfrb t lbotot t lbkhoz2 t lbkhox2 t lbkhov4 lupwait
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 59 local bus controller (elbc) note in pll bypass mode, lclk[n] is the inverted version of the internal clock with the delay of t lbkhkt. in this mode, signals are launched at the rising edge of the internal clock and are captured at the falling edge of the internal clock with the exception of lgta /lupwait (which is captured on the rising edge of the internal clock). lale output negation to high impedance for lad/ldp (latch hold time) t lbotot 1.5 ? ns 6 local bus clock to output valid (except lad/ldp and lale) t lbklov1 ?? 0 . 3n s local bus clock to data valid for lad/ldp t lbklov2 ?? 0 . 1n s4 local bus clock to address valid for lad t lbklov3 ?0 . 0n s4 local bus clock to lale assertion t lbklov4 ?0 . 0n s4 output hold from local bus clock (except lad/ldp and lale) t lbklox1 ?3.3 ? ns 4 output hold from local bus clock for lad/ldp t lbklox2 ?3.3 ? ns 4 local bus clock to output high impedance (except lad/ldp and lale) t lbkloz1 ?0 . 2n s7 local bus clock to output high impedance for lad/ldp t lbkloz2 ?0 . 2n s7 notes: 1. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t lbixkh1 symbolizes local bus timing (lb) for the input (i) to go invalid (x) with respect to the time the t lbk clock reference (k) goes high (h), in this case for clock one(1). also, t lbkhox symbolizes local bus timing (lb) for the t lbk clock reference (k) to go high (h), with respect to the output (o) going invalid (x) or output hold time. 2. all timings are in reference to local bus clock for pll bypass mode. timings may be negative with respect to the local bus clock because the actual launch and capture of signals is done with the internal launch/capture clock, which precedes lclk by t lbkhkt . 3. maximum possible clock skew between a clock lclk[m] and a relative clock lclk[n]. skew measured between complementary signals at bv dd /2. 4. all signals are measured from bvdd/2 of the rising edge of local bus clock for pll bypass mode to 0.4 x bvdd of the signal in question for 3.3-v signaling levels. 5. input timings are measured at the pin. 6. t lbotot is a measurement of the minimum time between the negation of lale and any change in lad. t lbotot is programmed with the lbcr[ahd] parameter. 7. for purposes of active/float timing measurements, the hi-z or off state is defined to be when the total current delivered thr ough the component pin is less than or equal to the leakage current specification. table 51. local bus general timing parameters?pll bypassed (continued) at recommended operating conditions with bv dd of 3.3 v 5% parameter symbol 1 min max unit notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 60 freescale semiconductor local bus controller (elbc) figure 31. local bus signals (pll bypass mode) output signals: la[27:31]/lcs [0:7]/ lwe [0:3]/lfwe / lbctl/lfcle/lfale / t lbklov2 lclk[n] input signals: lad[0:31]/ldp[0:3] output (data) signals: lad[0:31]/ldp[0:3] lale t lbixkh1 input signal: lgta/ lfrb output (address) signal: lad[0:31] t lbivkh1 t lbixkl2 t lbivkl2 t lbklox1 t lbkloz2 t lbotot internal launch/ t lbklox2 t lbklov1 t lbklov3 t lbkloz1 t lbkhkt t lbklov4 lupwait capture clock loe /lfre /lfwp
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 61 local bus controller (elbc) figure 32. local bus signals, gpcm/upm signals for lccr[clkdiv] = 4 (pll enabled) lsync_in upm mode input signal: lupwait t lbixkh2 t lbivkh2 t lbivkh1 t lbixkh1 t lbkhoz1 t1 t3 input signals: lad[0:31]/ldp[0:3] upm mode output signals: lcs [0:7]/lbs [0:3]/lgpl[0:5] gpcm mode output signals: lcs [0:7]/lwe t lbkhov1 t lbkhov1 t lbkhoz1 gpcm mode input signal: lgta
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 62 freescale semiconductor local bus controller (elbc) figure 33. local bus si gnals, gpcm/upm signals for lccr[clkdiv] = 4 (pll bypass mode) t lbivkh1 t lbixkl2 internal launch/capture clock upm mode input signal: lupwait t1 t3 input signals: lad[0:31]/ldp[0:3] upm mode output signals: lcs [0:7]/lbs [0:3]/lgpl[0:5] gpcm mode output signals: lcs [0:7]/lwe t lbklov1 t lbkloz1 lclk t lbklox1 t lbixkh1 gpcm mode input signal: lgta t lbivkl2
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 63 local bus controller (elbc) figure 34. local bus signals, gpcm/upm signal s for lccr[clkdiv] = 8 or 16 (pll enabled) lsync_in upm mode input signal: lupwait t lbixkh2 t lbivkh2 t lbivkh1 t lbixkh1 t lbkhoz1 t1 t3 upm mode output signals: lcs [0:7]/lbs [0:3]/lgpl[0:5] gpcm mode output signals: lcs [0:7]/lwe t lbkhov1 t lbkhov1 t lbkhoz1 t2 t4 input signals: lad[0:31]/ldp[0:3] gpcm mode input signal: lgta
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 64 freescale semiconductor local bus controller (elbc) figure 35. local bus signals, gpcm/upm signals for lccr[clkdiv] = 8 or 16 (pll bypass mode) t lbixkl2 t lbivkh1 internal launch/capture clock upm mode input signal: lupwait t1 t3 upm mode output signals: lcs [0:7]/lbs [0:3]/lgpl[0:5] gpcm mode output signals: lcs [0:7]/lwe t2 t4 input signals: lad[0:31]/ldp[0:3] lclk t lbklov1 t lbkloz1 t lbklox1 t lbixkh1 gpcm mode input signal: lgta t lbivkl2
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 65 programmable interrupt controller 11 programmable interrupt controller in irq edge trigger mode, when an external interr upt signal is asserted (according to the programmed polarity), it must remain asserted for at least 3 system clocks (sysclk periods). 12 jtag this section describes the ac electrical specifica tions for the ieee 1149.1 (jtag) interface of the MPC8572E. table 52 provides the jtag ac timing specifications as defined in figure 37 through figure 39 . table 52. jtag ac timing specifications (independent of sysclk) 1 at recommended operating conditions with ov dd of 3.3 v 5%. parameter symbol 2 min max unit notes jtag external clock frequency of operation f jtg 0 33.3 mhz ? jtag external clock cycle time t jtg 30 ? ns ? jtag external clock pulse width measured at 1.4 v t jtkhkl 15 ? ns ? jtag external clock rise and fall times t jtgr & t jtgf 02 n s 6 trst assert time t trst 25 ? ns 3 input setup times: boundary-scan data tms, tdi t jtdvkh t jtivkh 4 0 ? ? ns 4 input hold times: boundary-scan data tms, tdi t jtdxkh t jtixkh 20 25 ? ? ns 4 valid times: boundary-scan data tdo t jtkldv t jtklov 4 4 20 25 ns 5 output hold times: boundary-scan data tdo t jtkldx t jtklox 30 30 ? ? ns 5
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 66 freescale semiconductor jtag figure 36 provides the ac test load for tdo and the boundary-scan outputs. figure 36. ac test load for the jtag interface figure 37 provides the jtag clock input timing diagram. figure 37. jtag clock input timing diagram figure 38 provides the trst timing diagram. figure 38. trst timing diagram jtag external clock to output high impedance: boundary-scan data tdo t jtkldz t jtkloz 3 3 19 9 ns 5, 6 notes: 1. all outputs are measured from the midpoint voltage of the falling/rising edge of t tclk to the midpoint of the signal in question. the output timings are measured at the pins. all output timings assume a purely resistive 50- load (see figure 36 ). time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. the symbols used for timing specifications herein follow the pattern of t (first two letters of functional block)(signal)(state) (reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t jtdvkh symbolizes jtag device timing (jt) with respect to the time data input signals (d) reaching the valid state (v) relative to the t jtg clock reference (k) going to the high (h) state or setup time. also, t jtdxkh symbolizes jtag timing (jt) with respect to the time data input signals (d) went invalid (x) relative to the t jtg clock reference (k) going to the high (h) state. note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. for rise and fall times, the latter convention is used with the appropriate letter: r (rise) or f (fall). 3. trst is an asynchronous level sensitive signal. the setup time is for test purposes only. 4. non-jtag signal input timing with respect to t tclk . 5. non-jtag signal output timing with respect to t tclk . 6. guaranteed by design. table 52. jtag ac timing specifications (independent of sysclk) 1 (continued) at recommended operating conditions with ov dd of 3.3 v 5%. parameter symbol 2 min max unit notes output z 0 = 50 ov dd /2 r l = 50 jtag t jtkhkl t jtgr external clock vm vm vm t jtg t jtgf vm = midpoint voltage (ov dd /2) trst vm = midpoint voltage (ov dd /2) vm vm t trst
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 67 i 2 c figure 39 provides the boundary-scan timing diagram. figure 39. boundary-scan timing diagram 13 i 2 c this section describes the dc and ac electrical characteristics for the i 2 c interfaces of the MPC8572E. 13.1 i 2 c dc electrical characteristics table 53 provides the dc electrical characteristics for the i 2 c interfaces. table 53. i 2 c dc electrical characteristics parameter symbol min max unit notes input high voltage level v ih 0.7 ov dd ov dd + 0.3 v ? input low voltage level v il ?0.3 0.3 ov dd v? low level output voltage v ol 00 . 4 v1 pulse width of spikes which must be suppressed by the input filter t i2khkl 05 0n s2 input current each i/o pin (input voltage is between 0.1 ov dd and 0.9 ov dd (max) i i ?10 10 a3 capacitance for each i/o pin c i ?1 0p f? notes: 1. output voltage (open drain or open collector) condition = 3 ma sink current. 2. refer to the MPC8572E powerquicc? iii integrated host processor family reference manual for information on the digital filter used. 3. i/o pins will obstruct the sda and scl lines if ov dd is switched off. vm = midpoint voltage (ov dd /2) vm vm t jtdvkh t jtdxkh boundary data outputs boundary data outputs jtag external clock boundary data inputs output data valid t jtkldx t jtkldz t jtkldv input data valid output data valid
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 68 freescale semiconductor i 2 c 13.2 i 2 c ac electrical specifications table 54 provides the ac timing parameters for the i 2 c interfaces. table 54. i 2 c ac electrical specifications at recommended operating conditions with ov dd of 3.3 v 5%. all values refer to v ih (min) and v il (max) levels (see ta b l e 2 ). parameter symbol 1 min max unit scl clock frequency f i2c 04 0 0k h z 4 low period of the scl clock t i2cl 1.3 ? s high period of the scl clock t i2ch 0.6 ? s setup time for a repeated start condition t i2svkh 0.6 ? s hold time (repeated) start condition (after this period, the first clock pulse is generated) t i2sxkl 0.6 ? s data setup time t i2dvkh 100 ? ns data input hold time: cbus compatible masters i 2 c bus devices t i2dxkl ? 0 2 ? ? s data output delay time t i2ovkl ?0 . 9 3 s setup time for stop condition t i2pvkh 0.6 ? s bus free time between a stop and start condition t i2khdx 1.3 ? s noise margin at the low level for each connected device (including hysteresis) v nl 0.1 ov dd ?v noise margin at the high level for each connected device (including hysteresis) v nh 0.2 ov dd ?v capacitive load for each bus line cb ? 400 pf notes: 1.the symbols used for timing specifications herein follow the pattern t (first two letters of functional block)(signal)(state)(reference)(state) for inputs and t (first two letters of functional block)(reference)(state)(signal)(state) for outputs. for example, t i2dvkh symbolizes i 2 c timing (i2) with respect to the time data input signals (d) reach the valid state (v) relative to the t i2c clock reference (k) going to the high (h) state or setup time. also, t i2sxkl symbolizes i 2 c timing (i2) for the time that the data with respect to the start condition (s) went invalid (x) relative to the t i2c clock reference (k) going to the low (l) state or hold time. also, t i2pvkh symbolizes i 2 c timing (i2) for the time that the data with respect to the stop condition (p) reaching the valid state (v) relative to the t i2c clock reference (k) going to the high (h) state or setup time. 2. as a transmitter, the MPC8572E provides a delay time of at least 300 ns for the sda signal (referred to the vihmin of the scl signal) to bridge the undefined region of the falling edge of scl to avoid unintended generation of start or stop condition. when the MPC8572E acts as the i2c bus master while transmitting, the MPC8572E drives both scl and sda. as long as the load on scl and sda are balanced, the MPC8572E would not cause unintended generation of start or stop condition. therefore, the 300 ns sda output delay time is not a concern. if, under some rare condition, the 300 ns sda output delay time is required for the MPC8572E as transmitter, applicat ion note an2919 referred to in note 4 below is recommended. 3.the maximum t i2ovkl has only to be met if the device does not stretch the low period (t i2cl ) of the scl signal. 4. the requirements for i 2 c frequency calculation must be followed. refer to freescale application note an2919, determining the i 2 c frequency divider ratio for scl .
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 69 gpio figure 40 provides the ac test load for the i 2 c. figure 40. i 2 c ac test load figure 41 shows the ac timing diagram for the i 2 c bus. figure 41. i 2 c bus ac timing diagram 14 gpio this section describes the dc and ac electrical sp ecifications for the gpio interface of the MPC8572E. 14.1 gpio dc electrical characteristics table 55 provides the dc electrical characteristics for the gpio interface operating at bv dd = 3.3 v dc. table 55. gpio dc electrical characteristics (3.3 v dc) parameter symbol min max unit supply voltage 3.3v bv dd 3.13 3.47 v high-level input voltage v ih 2b v dd + 0.3 v low-level input voltage v il ?0.3 0.8 v input current (bv in 1 = 0 v or bv in =bv dd ) i in ? 5 a high-level output voltage (bv dd =min, i oh =?2 ma) v oh bv dd ?0.2 ? v low-level output voltage (bv dd =min, i ol =2 ma) v ol ?0 . 2 v note: 1. note that the symbol bv in , in this case, represents the bv in symbol referenced in ta ble 1 . output z 0 = 50 ov dd /2 r l = 50 sr s sda scl t i2sxkl t i2cl t i2ch t i2dxkl t i2dvkh t i2sxkl t i2svkh t i2khkl t i2pvkh ps
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 70 freescale semiconductor gpio table 56 provides the dc electrical characteristics for the gpio interface operating at bv dd = 2.5 v dc. table 57 provides the dc electrical characteristics for the gpio interface operating at bv dd = 1.8 v dc. table 56. gpio dc electrical characteristics (2.5 v dc) parameter symbol min max unit supply voltage 2.5v bv dd 2.37 2.63 v high-level input voltage v ih 1.70 bv dd +0.3 v low-level input voltage v il ?0.3 0.7 v input current (bv in 1 = 0 v or bv in = bv dd ) i ih ?1 0 a i il ?15 high-level output voltage (bv dd =min, i oh =?1 ma) v oh 2.0 bv dd + 0.3 v low-level output voltage (bv dd min, i ol = 1 ma) v ol gnd ? 0.3 0.4 v note: 1. the symbol bv in , in this case, represents the bv in symbol referenced in ta b l e 1 . table 57. gpio dc electrical characteristics (1.8 v dc) parameter symbol min max unit supply voltage 1.8v bv dd 1.71 1.89 v high-level input voltage v ih 0.65 x bv dd bv dd +0.3 v low-level input voltage v il ?0.3 0.35 x bv dd v input current (bv in 1 = 0 v or bv in =bv dd ) i in tbd tbd a high-level output voltage (i oh = ?100 a) v oh bv dd ? 0.2 ? v high-level output voltage (i oh =?2 ma) v oh bv dd ? 0.45 ? v low-level output voltage (i ol =100 a) v ol ?0 . 2 v low-level output voltage (i ol =2ma) v ol ?0 . 4 5 v note: 1. the symbol bv in , in this case, represents the bv in symbol referenced in ta ble 1 .
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 71 high-speed serial interfaces (hssi) 14.2 gpio ac electrical specifications table 58 provides the gpio input and output ac timing specifications. figure 42 provides the ac test load for the gpio. figure 42. gpio ac test load 15 high-speed serial interfaces (hssi) the MPC8572E features two serializer/deserializer (serdes) interfaces to be used for high-speed serial interconnect applications. the serdes1 interface can be used for pci express and/or serial rapidio data transfers. the serdes2 is dedicated for sgmii application. this section describes the common portion of serdes dc electrical specifications, which is the dc requirement for serdes reference clocks. the serdes data lane?s transmitter and receiver reference circuits are also shown. 15.1 signal terms definition the serdes utilizes differential signaling to transfer data across the serial link. this section defines terms used in the description and specification of differential signals. figure 43 shows how the signals are defined. for illustration purpose, only one serdes lane is used for description. the figure shows waveform for either a transmitter output (sdn_tx and sdn_tx ) or a receiver input (sdn_rx and sdn_rx ). each signal swings between a volts and b volts where a > b. using this waveform, the definitions are as follows. to simplify illustration, the following definitions assume that the serdes transmitter and receiver opera te in a fully symmetrical differential signaling environment. 1. single-ended swing the transmitter output signals and the receiver input signals sdn_tx, sdn_tx , sdn_rx and sdn_rx each have a peak-to-peak swing of a - b volts. this is also referred as each signal wire?s single-ended swing. table 58. gpio input ac timing specifications 1 parameter symbol typ unit notes gpio inputs?minimum pulse width t piwid 20 ns 2 notes: 1. input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of sysclk. timings are measured at the pin. 2. gpio inputs and outputs are asynchronous to any visible clock. gpio outputs should be synchronized before use by any external synchronous logic. gpio inputs are required to be valid for at least t piwid ns to ensure proper operation. output z 0 = 50 bv dd /2 r l = 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 72 freescale semiconductor high-speed serial interfaces (hssi) 2. differential output voltage, v od (or differential output swing ): the differential output voltage (or swing) of the transmitter, v od , is defined as the difference of the two complimentary output voltages: v sd n _tx ? v sd n _tx . the v od value can be either positive or negative. 3. differential input voltage, v id (or differential input swing ): the differential input voltage (or swing) of the receiver, v id , is defined as the difference of the two complimentary input voltages: v sd n _rx - v sd n _rx . the v id value can be either positive or negative. 4. differential peak voltage , v diffp the peak value of the differential transmitter output signal or the differential receiver input signal is defined as differential peak voltage, v diffp = |a ? b| volts. 5. differential peak-to-peak , v diffp-p because the differential output signal of the transmitter and the differential input signal of the receiver each range from a ? b to ?(a ? b) volts, the peak-to-peak value of the differential transmitter output signal or the differential receiver input signal is defined as differential peak-to-peak voltage, v diffp-p = 2*v diffp = 2 * |(a ? b)| volts, which is twice of differential swing in amplitude, or twice of the differential peak. for example, the output differential peak-peak voltage can also be calculated as v tx-diffp-p = 2*|v od |. 6. differential waveform 1. the differential waveform is constructe d by subtracting the inverting signal (sd n _tx , for example) from the non-inverting signal (sdn_tx, fo r example) within a differential pair. there is only one signal trace curve in a differential waveform. the voltage represented in the differential waveform is not referenced to ground. refer to figure 52 as an example for differential waveform. 2. common mode voltage, v cm the common mode voltage is equa l to one half of the sum of the voltages between each conductor of a balanced interchange circuit and ground. in this example, for serdes output, v cm_out = (v sd n _tx + v sd n _tx )/2 = (a + b) / 2, which is the arithmetic mean of the two complimentary output voltages within a differential pair. in a system, the common mode voltage may often differ from one component?s output to the other?s input. sometimes, it may be even different between the receiver input and driver output circuits within th e same component. it is also referred as the dc offset in some occasion.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 73 high-speed serial interfaces (hssi) figure 43. differential voltage definitions for transmitter or receiver to illustrate these definitions using real values, consider the case of a cml (current mode logic) transmitter that has a common mode voltage of 2.25 v and each of its outputs, td and td , has a swing that goes between 2.5 v and 2.0 v. us ing these values, the peak-to-peak voltage swing of each signal (td or td ) is 500 mv p-p, which is referred as the single-ended swing for each signal. in this example, because the differential signaling environment is fully symmetrical, the transmitter output?s differential swing (v od ) has the same amplitude as each signal?s single-ended swing. the differential output signal ranges between 500 mv and ?500 mv, in other words, v od is 500 mv in one phase and ?500 mv in the other phase. the peak differential voltage (v diffp ) is 500 mv. the peak-to-peak differential voltage (v diffp-p ) is 1000 mv p-p. 15.2 serdes reference clocks the serdes reference clock inputs are applied to an internal pll whose output creates the clock used by the corresponding serdes lanes. the serdes reference clocks inputs are sd1_ref_clk and sd1_ref_clk for pci express and serial rapidio, or sd2_ref_clk and sd2_ref_clk for the sgmii interface respectively. the following sections describe the serdes re ference clock requirement s and some application information. 15.2.1 serdes reference clock receiver characteristics figure 44 shows a receiver reference diagram of the serdes reference clocks. characteristics are as follows: ? the supply voltage requirements for xv dd_srds2 are specified in table 1 and table 2 . ? serdes reference clock receiver reference circuit structure ?the sd n _ref_clk and sd n _ref_clk are internally ac-coupled differential inputs as shown in figure 44 . each differential clock input (sd n _ref_clk or sd n _ref_clk ) has on-chip 50- termination to sgnd_srdsn (xcorevss) followed by on-chip ac-coupling. differential swing, v id or v od = a ? b a volts b volts sdn_tx or sdn_rx sdn_tx or sdn_rx differential peak voltage, v diffp = |a ? b| differential peak-peak voltage, v diffpp = 2*v diffp (not shown) v cm = (a + b) / 2
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 74 freescale semiconductor high-speed serial interfaces (hssi) ? the external reference clock driver must be able to drive this termination. ? the serdes reference clock input can be eith er differential or single-ended. refer to the differential mode and single-ended mode descri ption below for further detailed requirements. ? the maximum average current requirement that also determines the common mode voltage range ? when the serdes reference clock differential i nputs are dc coupled externally with the clock driver chip, the maximum average current allowed for each input pin is 8 ma. in this case, the exact common mode input voltage is not critical as long as it is within the range allowed by the maximum average current of 8 ma (refer to the following bullet for more detail), because the input is ac-coupled on-chip. ? this current limitation sets the maximum common m ode input voltage to be less than 0.4 v (0.4 v/50 = 8 ma) while the minimum common mode input level is 0.1 v above sgnd_srds n (xcorevss). for example, a clock with a 50/50 duty cycle can be produced by a clock driver with output driven by its current source from 0 ma to 16 ma (0-0.8 v), such that each phase of the differential input has a single-ended swing from 0 v to 800 mv with the common mode voltage at 400 mv. ? if the device driving the sd n _ref_clk and sd n _ref_clk inputs cannot drive 50 to sgnd_srds n (xcorevss) dc, or it exceeds the maximum input current limitations, then it must be ac-coupled off-chip. ? the input amplitude requirement ? this requirement is described in detail in the following sections. figure 44. receiver of serdes reference clocks 15.2.2 dc level requirement for serdes reference clocks the dc level requirement for the MPC8572E serdes reference clock inputs is different depending on the signaling mode used to connect the clock driver ch ip and serdes reference clock inputs as described below. ? differential mode ? the input amplitude of the differential clock must be between 400mv and 1600mv differential peak-peak (or between 200mv and 800mv differential peak). in other words, each signal wire input amp 50 50 sd n _ref_clk sd n _ref_clk
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 75 high-speed serial interfaces (hssi) of the differential pair must have a single- ended swing less than 800mv and greater than 200mv. this requirement is the same for both external dc-coupled or ac-coupled connection. ? for external dc-coupled connection, as described in section 15.2.1, ?serdes reference clock receiver characteristics ,? the maximum average current requirements sets the requirement for average voltage (common mode voltage) to be between 100 mv and 400 mv. figure 45 shows the serdes reference clock input requirement for dc-coupled connection scheme. ? for external ac-coupled connection, there is no common m ode voltage requirement for the clock driver. because the external ac-coupling capacitor blocks the dc level, the clock driver and the serdes reference clock receiver operate in different command mode voltages. the serdes reference clock receiver in this connec tion scheme has its common mode voltage set to sgnd_srds n . each signal wire of the differential inputs is allowed to swing below and above the command mode voltage (sgnd_srds n ). figure 46 shows the serdes reference clock input requirement for ac-coupled connection scheme. ? single-ended mode ? the reference clock can also be single-ended. the sd n _ref_clk input amplitude (single-ended swing) must be between 400 mv and 800 mv peak-peak (from vmin to vmax) with sd n _ref_clk either left unconnected or tied to ground. ?the sd n _ref_clk input average voltage must be between 200 and 400 mv. figure 47 shows the serdes reference clock input requirement for single-ended signaling mode. ? to meet the input amplitude requirement, the re ference clock inputs might need to be dc or ac-coupled externally. for the best noise performance, the reference of the clock could be dc or ac-coupled into the unused phase (sd n _ref_clk ) through the same source impedance as the clock input (sd n _ref_clk) in use. figure 45. differential reference clock input dc requirements (external dc-coupled) sd n _ref_clk sd n _ref_clk vmax < 800 mv vmin > 0v 100 mv < vcm < 400 mv 200mv < input amplitude or differential peak < 800 mv
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 76 freescale semiconductor high-speed serial interfaces (hssi) figure 46. differential reference clock input dc requirements (external ac-coupled) figure 47. single-ended reference clock input dc requirements 15.2.3 interfacing with other differential signaling levels ? with on-chip termination to sgnd_srds n (xcorevss), the differential reference clocks inputs are hcsl (high-speed current steering logic) compatible dc-coupled. ? many other low voltage differen tial type outputs like lvds (low voltage differential signaling) can be used but may need to be ac-coupled due to the limited common mode input range allowed (100 to 400 mv) for dc-coupled connection. ? lvpecl outputs can produce signal with too large amplitude and may need to be dc-biased at clock driver output first, then followed with series attenuation resistor to reduce the amplitude, additionally to ac-coupling. sd n _ref_clk sd n _ref_clk vcm 200 mv < input amplitude or differential peak < 800 mv vmax < vcm + 400 mv vmin > vcm ? 400 mv sd n _ref_clk sd n _ref_clk 400 mv < sd n _ref_clk input amplitude < 800 mv 0v
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 77 high-speed serial interfaces (hssi) note figure 48 to figure 51 below are for conceptual reference only. due to the fact that clock driver chip's inte rnal structure, output impedance and termination requirements are different between various clock driver chip manufacturers, it is very possible that the clock circuit reference designs provided by clock driver chip vendor are different from what is shown below. they might also vary from one vendor to the other. therefore, freescale semiconductor can neither provide the optimal clock driver reference circuits, nor guarantee the correctness of the following clock driver connection reference circuits. the system designer is recommended to contact the selected clock driver chip vendor for the optimal reference circuits with the MPC8572E serdes reference clock receiver requirement provided in this document. figure 48 shows the serdes reference clock connection reference circuits for hcsl type clock driver. it assumes that the dc levels of the clock driver chip is compatible with MPC8572E serdes reference clock input?s dc requirement. figure 48. dc-coupled differential connection with hcsl clock driver (reference only) 50 50 sd n _ref_clk sd n _ref_clk clock driver 100 differential pwb trace clock driver vendor dependent source termination resistor serdes refer. clk receiver clock driver clk_out clk_out hcsl clk driver chip 33 33 total 50 . assume clock driver?s output impedance is about 16 . MPC8572E clk_out
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 78 freescale semiconductor high-speed serial interfaces (hssi) figure 49 shows the serdes reference clock connection reference circuits for lvds type clock driver. because lvds clock driver?s common mode voltage is higher than the MPC8572E serdes reference clock input?s allowed range (100 to 400mv), ac-coupled connection scheme must be used. it assumes the lvds output driver features 50- termination resistor. it also assumes that the lvds transmitter establishes its own common mode level without rely ing on the receiver or other external component. figure 49. ac-coupled differential connection with lvds clock driver (reference only) figure 50 shows the serdes reference clock connection refe rence circuits for lvpecl type clock driver. because lvpecl driver?s dc levels (both common mode voltages and output swing) are incompatible with MPC8572E serdes reference clock input?s dc requirement, ac-coupling must be used. figure 50 assumes that the lvpecl clock driver?s output impedance is 50 . r1 is used to dc-bias the lvpecl outputs prior to ac-coupling. its value could be ranged from 140 to 240 depending on clock driver vendor?s requirement. r2 is used together with the serdes reference clock receiver?s 50- termination resistor to attenuate the lvpecl output?s differential peak level such that it meets the MPC8572E serdes reference clock?s differential input amplitude require ment (between 200mv and 800mv differential peak). for example, if the lvpecl output?s differential peak is 900mv and the desired serdes reference clock input amplitude is selected as 600mv, the attenuation factor is 0.67, which requires r2 = 25 . consult 50 50 sd n _ref_clk sd n _ref_clk clock driver 100 differential pwb trace serdes refer. clk receiver clock driver clk_out clk_out lvds clk driver chip 10 nf 10 nf mpc8572 e
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 79 high-speed serial interfaces (hssi) clock driver chip manufacturer to verify whether this connection scheme is comp atible with a particular clock driver chip. figure 50. ac-coupled differential connection with lvpecl clock driver (reference only) figure 51 shows the serdes reference clock connection refe rence circuits for a single-ended clock driver. it assumes the dc levels of the clock driver are compatible with MPC8572E serdes reference clock input?s dc requirement. figure 51. single-ended connection (reference only) 15.2.4 ac requirements for serdes reference clocks the clock driver selected should provide a high quality reference clock with low phase noise and cycle-to-cycle jitter. phase noise less than 100khz can be tracked by the pll and data recovery loops and is less of a problem. phase noise above 15mhz is f iltered by the pll. the most problematic phase noise 50 50 sd n _ref_clk sd n _ref_clk clock driver 100 differential pwb trace serdes refer. clk receiver clock driver clk_out clk_out lvpecl clk driver chip r2 r2 r1 MPC8572E r1 10nf 10nf 10nf 50 50 sd n _ref_clk sd n _ref_clk 100 differential pwb trace serdes refer. clk receiver clock driver clk_out single-ended clk driver chip MPC8572E 33 total 50 . assume clock driver?s output impedance is about 16 . 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 80 freescale semiconductor high-speed serial interfaces (hssi) occurs in the 1-15mhz range. the source impedance of the clock driver should be 50 ohms to match the transmission line and reduce reflections which are a source of noise to the system. table 59 describes some ac parameters common to sgmi i, pci express and serial rapidio protocols. figure 52. differential measurement points for rise and fall time table 59. serdes reference clock common ac parameters at recommended operating conditions with xv dd_srds1 or xv dd_srds2 = 1.1v 5%. parameter symbol min max unit notes rising edge rate rise edge rate 1.0 4.0 v/ns 2, 3 falling edge rate fall edge rate 1.0 4.0 v/ns 2, 3 differential input high voltage v ih +200 mv 2 differential input low voltage v il ?-200mv2 rising edge rate (sdn_ref_clk) to falling edge rate (sdn_ref_clk ) matching rise-fall matching ?20%1, 4 notes: 1. measurment taken from single ended waveform. 2. measurment taken from differential waveform. 3. measured from -200 mv to +200 mv on the differential waveform (derived from sdn_ref_clk minus sdn_ref_clk ). the signal must be monotonic through the measurement region for rise and fall time. the 400 mv measurement window is centered on the differential zero crossing. see figure 52 . 4. matching applies to rising edge rate for sdn_ref_clk and falling edge rate for sdn_ref_clk . it is measured using a 200 mv window centered on the median cross point where sdn_ref_clk rising meets sdn_ref_clk falling. the median cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. the rise edge rate of sdn_ref_clk should be compared to the fall edge rate of sdn_ref_clk , the maximum allowed difference should not exceed 20% of the slowest edge rate. see figure 53 . v ih = +200 mv v il = -200 mv 0.0 v sd n _ref_clk minus sd n _ref_clk
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 81 high-speed serial interfaces (hssi) figure 53. single-ended measurement points for rise and fall time matching the other detailed ac requirements of the serdes re ference clocks is defined by each interface protocol based on application usage. refer to the following sections for detailed information: ? section 8.3.2, ?ac requirements for sgmii sd2_ref_clk and sd2_ref_clk ? ? section 16.2, ?ac requirements for pci express serdes reference clocks ? ? section 17.2, ?ac requirements for serial rapidio sd1_ref_clk and sd1_ref_clk ? 15.2.4.1 spread spectrum clock sd1_ref_clk/sd1_ref_clk are designed to work with a spread spectrum clock (+0 to ?0.5% spreading at 30?33 khz rate is allowed), assuming both ends have same reference clock. for better results, a source without significant unintended modulation should be used. sd2_ref_clk/sd2_ref_clk are not to be used with, and should not be clocked by, a spread spectrum clock source. 15.3 serdes transmitter and receiver reference circuits figure 54 shows the reference circuits for serdes data lane?s transmitter and receiver. figure 54. serdes transmitter and receiver reference circuits the dc and ac specification of serdes data lanes ar e defined in each interface protocol section below (pci express, serial rapid io or sgmii) in this document based on the application usage: ? section 8.3, ?sgmii interface electrical characteristics ? sd n _ref_clk sd n _ref_clk sd n _ref_clk sd n _ref_clk 50 50 receiver transmitter sd1_tx n or sd2_tx n sd1_tx n or sd2_tx n sd1_rx n or sd2_rx n sd1_rx n or sd2_rx n 50 50
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 82 freescale semiconductor pci express ? section 16, ?pci express ? ? section 17, ?serial rapidio ? note that external ac coupling capacitor is required for the above three serial transmission protocols with the capacitor value defined in specification of each protocol section. 16 pci express this section describes the dc and ac electrical specifications for the pci express bus of the MPC8572E. 16.1 dc requirements for pci express sd1_ref_clk and sd1_ref_clk for more information, see section 15.2, ?serdes reference clocks.? 16.2 ac requirements for pci express serdes reference clocks table 60 lists ac requirements. 16.3 clocking dependencies the ports on the two ends of a link must transmit data at a rate that is within 600 parts per million (ppm) of each other at all times. this is specified to allow bit rate clock sources with a +/? 300 ppm tolerance. 16.4 physical layer specifications the following is a summary of the specifications for the physical layer of pci express on this device. for further details as well as the specifications of the transport and data link layer, use the pci express base specification. rev. 1.0a document. 16.4.1 differential transmitter (tx) output table 61 defines the specifications for the differential output at all transmitters (txs). the parameters are specified at the component pins. table 60. sd1_ref_clk and sd1_ref_clk ac requirements symbol parameter description min typical max units notes t ref refclk cycle time ? 10 ? ns 1 t refcj refclk cycle-to-cycle jitter. difference in the period of any two adjacent refclk cycles ? ? 100 ps ? t refpj phase jitter. deviation in edge location with respect to mean edge location ?50 ? 50 ps ? notes: 1. typical cycle time is based on pci express card electromechanical specification revision 1.0a.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 83 pci express table 61. differential transmitter (tx) output specifications symbol parameter min nominal max units comments ui unit interval 399.88 400 400.12 ps each ui is 400 ps 300 ppm. ui does not account for spread spectrum clock dictated variations. see note 1. v tx-diffp-p differential peak-to-peak output voltage 0.8 ? 1.2 v v tx-diffp-p = 2*|v tx-d+ - v tx-d- | see note 2. v tx-de-ratio de- emphasized differential output voltage (ratio) ?3.0 ?3.5 -4.0 db ratio of the v tx-diffp-p of the second and following bits after a transition divided by the v tx-diffp-p of the first bit after a transition. see note 2. t tx-eye minimum tx eye width 0.70 ? ? ui the maximum transmitter jitter can be derived as t tx-max-jitter = 1 - t tx-eye = 0.3 ui. see notes 2 and 3. t tx-eye-median-to- max-jitter maximum time between the jitter median and maximum deviation from the median. ? ? 0.15 ui jitter is defined as the measurement variation of the crossing points (v tx-diffp-p = 0 v) in relation to a recovered tx ui. a recovered tx ui is calculated over 3500 consecutive unit intervals of sample data. jitter is measured using all edges of the 250 consecutive ui in the center of the 3500 ui used for calculating the tx ui. see notes 2 and 3. t tx-rise , t tx-fall d+/d- tx output rise/fall time 0.125 ? ? ui see notes 2 and 5 v tx-cm-acp rms ac peak common mode output voltage ??20mvv tx-cm-acp = rms(|v txd+ + v txd- |/2 - v tx-cm-dc ) v tx-cm-dc = dc (avg) of |v tx-d+ + v tx-d- |/2 see note 2 v tx-cm-dc-active- idle-delta absolute delta of dc common mode voltage during l0 and electrical idle 0?100mv|v tx-cm-dc (during l0) - v tx-cm-idle-dc (during electrical idle) |<=100 mv v tx-cm-dc = dc (avg) of |v tx-d+ + v tx-d- |/2 [l0] v tx-cm-idle-dc = dc (avg) of |v tx-d+ + v tx-d- |/2 [electrical idle] see note 2. v tx-cm-dc-line-delta absolute delta of dc common mode between d+ and d? 0?25mv|v tx-cm-dc-d+ - v tx-cm-dc-d- | <= 25 mv v tx-cm-dc-d+ = dc (avg) of |v tx-d+ | v tx-cm-dc-d- = dc (avg) of |v tx-d- | see note 2. v tx-idle-diffp electrical idle differential peak output voltage 0?20mvv tx-idle-diffp = |v tx-idle-d+ -v tx-idle-d- | <= 20 mv see note 2. v tx-rcv-detect the amount of voltage change allowed during receiver detection ? 600 mv the total amount of voltage change that a transmitter can apply to sense whether a low impedance receiver is present. see note 6. v tx-dc-cm the tx dc common mode voltage 0 ? 3.6 v the allowed dc common mode voltage under any conditions. see note 6.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 84 freescale semiconductor pci express i tx-short tx short circuit current limit ? 90 ma the total current the transmitter can provide when shorted to its ground t tx-idle-min minimum time spent in electrical idle 50 ? ? ui minimum time a transmitter must be in electrical idle utilized by the receiver to start looking for an electrical idle exit after successfully receiving an electrical idle ordered set t tx-idle-set-to-idle maximum time to transition to a valid electrical idle after sending an electrical idle ordered set ? ? 20 ui after sending an electrical idle ordered set, the transmitter must meet all electrical idle specifications within this time. this is considered a debounce time for the transmitter to meet electrical idle after transitioning from l0. t tx-idle-to-diff-data maximum time to transition to valid tx specifications after leaving an electrical idle condition ? ? 20 ui maximum time to meet all tx specifications when transitioning from electrical idle to sending differential data. this is considered a debounce time for the tx to meet all tx specifications after leaving electrical idle rl tx-diff differential return loss 12 ? ? db measured over 50 mhz to 1.25 ghz. see note 4 rl tx-cm common mode return loss 6 ? ? db measured over 50 mhz to 1.25 ghz. see note 4 z tx-diff-dc dc differential tx impedance 80 100 120 tx dc differential mode low impedance z tx-dc transmitter dc impedance 40 ? ? required tx d+ as well as d- dc impedance during all states l tx-skew lane-to-lane output skew ? ? 500 + 2 ui ps static skew between any two transmitter lanes within a single link c tx ac coupling capacitor 75 ? 200 nf all transmitters shall be ac coupled. the ac coupling is required either within the media or within the transmitting component itself. see note 8. table 61. differential transmitter (tx) output specifications (continued) symbol parameter min nominal max units comments
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 85 pci express 16.4.2 transmitter compliance eye diagrams the tx eye diagram in figure 55 is specified using the passive compliance/test measurement load (see figure 57 ) in place of any real pci express interconnect + rx component. there are two eye diagrams that must be met for the transmitter. both eye diagrams must be aligned in time using the jitter median to locate the center of the eye diagram. the different eye diagrams differ in voltage depending whether it is a transition bit or a de -emphasized bit. the exact reduced voltage level of the de-emphasized bit is always relative to the transition bit. the eye diagram must be valid for any 250 consecutive uis. a recovered tx ui is calculated over 3500 consecutive un it intervals of sample data. the eye diagram is created using all edges of the 250 consecutive ui in the center of the 3500 ui used for calculating the tx ui. note it is recommended that the recovered tx ui is calculated using all edges in the 3500 consecutive ui interval with a fit algorithm using a minimization merit function (that is, least squa res and median deviation fits). t crosslink crosslink random timeout 0 ? 1 ms this random timeout helps resolve conflicts in crosslink configuration by eventually resulting in only one downstream and one upstream port. see note 7. notes: 1. no test load is necessarily associated with this value. 2. specified at the measurement point into a timing and voltage compliance test load as shown in figure 57 and measured over any 250 consecutive tx uis. (also refer to the transmitter compliance eye diagram shown in figure 55 .) 3. a t tx-eye = 0.70 ui provides for a total sum of deterministic and random jitter budget of t tx-jitter-max = 0.30 ui for the transmitter collected over any 250 consecutive tx uis. the t tx-eye-median-to-max-jitter median is less than half of the total tx jitter budget collected over any 250 consecutive tx uis. it should be noted that the median is not the same as the mean. the jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. 4. the transmitter input impedance shall result in a differential return loss greater than or equal to 12 db and a common mode return loss greater than or equal to 6 db over a frequency range of 50 mhz to 1.25 ghz. this input impedance requirement applies to all valid input levels. the reference impedance for return loss measurements is 50 ohms to ground for both the d+ and d- line (that is, as measured by a vector network analyzer with 50 ohm probes?see figure 57 ). note that the series capacitors c tx is optional for the return loss measurement. 5. measured between 20-80% at transmitter package pins into a test load as shown in figure 57 for both v tx-d+ and v tx-d- . 6. see section 4.3.1.8 of the pci express base specifications rev 1.0a. 7. see section 4.2.6.3 of the pci express base specifications rev 1.0a. 8. MPC8572E serdes transmitter does not have c tx built-in. an external ac coupling capacitor is required. table 61. differential transmitter (tx) output specifications (continued) symbol parameter min nominal max units comments
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 86 freescale semiconductor pci express figure 55. minimum transmitter timing and voltage output compliance specifications 16.4.3 differential receiver (rx) input specifications table 62 defines the specifications for the differential i nput at all receivers (rxs). the parameters are specified at the component pins. table 62. differential receiver (rx) input specifications symbol parameter min nominal max units comments ui unit interval 399.88 400 400.12 ps each ui is 400 ps 300 ppm. ui does not account for spread spectrum clock dictated variations. see note 1. v rx-diffp-p differential input peak-to-peak voltage 0.175 ? 1.200 v v rx-diffp-p = 2*|v rx-d+ - v rx-d- | see note 2. t rx-eye minimum receiver eye width 0.4 ? ? ui the maximum interconnect media and transmitter jitter that can be tolerated by the receiver can be derived as t rx-max-jitter = 1 - t rx-eye = 0.6 ui. see notes 2 and 3.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 87 pci express t rx-eye-median-to-max -jitter maximum time between the jitter median and maximum deviation from the median. ? ? 0.3 ui jitter is defined as the measurement variation of the crossing points (v rx-diffp-p = 0 v) in relation to a recovered tx ui. a recovered tx ui is calculated over 3500 consecutive unit intervals of sample data. jitter is measured using all edges of the 250 consecutive ui in the center of the 3500 ui used for calculating the tx ui. see notes 2, 3 and 7. v rx-cm-acp ac peak common mode input voltage ?? 150mvv rx-cm-acp = |v rxd+ +v rxd- |/2 - v rx-cm-dc v rx-cm-dc = dc (avg) of |v rx-d+ + v rx-d- |/2 see note 2 rl rx-diff differential return loss 15 ? ? db measured over 50 mhz to 1.25 ghz with the d+ and d- lines biased at +300 mv and -300 mv, respectively. see note 4 rl rx-cm common mode return loss 6 ? ? db measured over 50 mhz to 1.25 ghz with the d+ and d- lines biased at 0 v. see note 4 z rx-diff-dc dc differential input impedance 80 100 120 rx dc differential mode impedance. see note 5 z rx-dc dc input impedance 40 50 60 required rx d+ as well as d- dc impedance (50 20% tolerance). see notes 2 and 5. z rx-high-imp-dc powered down dc input impedance 200 k ? ? required rx d+ as well as d- dc impedance when the receiver terminations do not have power. see note 6. v rx-idle-det-diffp-p electrical idle detect threshold 65 ? 175 mv v rx-idle-det-diffp-p = 2*|v rx-d+ -v rx-d- | measured at the package pins of the receiver t rx-idle-det-diff- entertime unexpected electrical idle enter detect threshold integration time ? ? 10 ms an unexpected electrical idle (v rx-diffp-p < v rx-idle-det-diffp-p ) must be recognized no longer than t rx-idle-det-diff-entering to signal an unexpected idle condition. table 62. differential receiver (rx) input specifications (continued) symbol parameter min nominal max units comments
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 88 freescale semiconductor pci express l rx-skew total skew ? ? 20 ns skew across all lanes on a link. this includes variation in the length of skp ordered set (for example, com and one to five skp symbols) at the rx as well as any delay differences arising from the interconnect itself. notes: 1. no test load is necessarily associated with this value. 2. specified at the measurement point and measured over any 250 consecutive uis. the test load in figure 57 should be used as the rx device when taking measurements (also refer to the receiver compliance eye diagram shown in figure 56 ). if the clocks to the rx and tx are not derived from the same reference clock, the tx ui recovered from 3500 consecutive ui must be used as a reference for the eye diagram. 3. a t rx-eye = 0.40 ui provides for a total sum of 0.60 ui deterministic and random jitter budget for the transmitter and interconnect collected any 250 consecutive uis. the t rx-eye-median-to-max-jitter specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total. ui jitter budget collected over any 250 consecutive tx uis. it should be noted that the median is not the same as the mean. the jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. if the clocks to the rx and tx are not derived from the same reference clock, the tx ui recovered from 3500 consecutive ui must be used as the reference for the eye diagram. 4. the receiver input impedance shall result in a differential return loss greater than or equal to 15 db with the d+ line bias ed to 300 mv and the d- line biased to -300 mv and a common mode return loss greater than or equal to 6 db (no bias required) over a frequency range of 50 mhz to 1.25 ghz. this input impedance requirement applies to all valid input levels. the reference impedance for return loss measurements for is 50 ohms to ground for both the d+ and d- line (that is, as measured by a vector network analyzer with 50 ohm probes - see figure 57 ). note: that the series capacitors ctx is optional for the return loss measurement. 5. impedance during all ltssm states. when transitioning from a fundamental reset to detect (the initial state of the ltssm) there is a 5 ms transition time before receiver termination values must be met on all un-configured lanes of a port. 6. the rx dc common mode impedance that exists when no power is present or fundamental reset is asserted. this helps ensure that the receiver detect circuit does not falsely assume a receiver is powered on when it is not. this term must be measured at 300 mv above the rx ground. 7. it is recommended that the recovered tx ui is calculated using all edges in the 3500 consecutive ui interval with a fit algo rithm using a minimization merit function. least squares and median deviation fits have worked well with experimental and simulated data. table 62. differential receiver (rx) input specifications (continued) symbol parameter min nominal max units comments
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 89 pci express 16.5 receiver compliance eye diagrams the rx eye diagram in figure 56 is specified using the passive compliance/test measurement load (see figure 57 ) in place of any real pci express rx component. note: in general, the minimum receiver eye diagram measured with the compliance/test measurement load (see figure 57 ) is larger than the minimum receiver eye diagram measured over a range of systems at the input receiver of any real pci express com ponent. the degraded eye diagram at the input receiver is due to traces internal to the package as well as silicon parasitic characteristics which cause the real pci express component to vary in impedance from the compliance/test measurement load. the input receiver eye diagram is implementation specific and is not specified. rx component designer should provide additional margin to adequately compensate for the degraded minimum receiver eye diagram (shown in figure 56 ) expected at the input receiver based on some adequate combination of system simulations and the return loss measured looking into the rx package and silicon. the rx eye diagram must be aligned in time using the jitter median to locate the center of the eye diagram. the eye diagram must be valid for any 250 consecutive uis. a recovered tx ui is calculated over 3500 consecutive un it intervals of sample data. the eye diagram is created using all edges of the 250 consecutive ui in the center of the 3500 ui used for calculating the tx ui. note the reference impedance for return loss measurements is 50. to ground for both the d+ and d- line (that is, as measured by a vector network analyzer with 50. probes?see figure 57 ). note that the series capacitors, ctx, are optional for the return loss measurement. figure 56. minimum receiver eye timing and voltage compliance specification
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 90 freescale semiconductor serial rapidio 16.5.1 compliance test and measurement load the ac timing and voltage parameters must be verified at the measurement point, as specified within 0.2 inches of the package pins, into a test/measurement load shown in figure 57 . note the allowance of the measurement point to be within 0.2 inches of the package pins is meant to acknowledge that package/board routing may benefit from d+ and d? not being exac tly matched in length at the package pin boundary. figure 57. compliance test/measurement load 17 serial rapidio this section describes the dc and ac electrical spec ifications for the rapidio interface of the MPC8572E for the lp-serial physical layer. the electrical speci fications cover both single and multiple-lane links. two transmitters (short run and long run) and a single re ceiver are specified for each of three baud rates, 1.25, 2.50, and 3.125 gbaud. two transmitter specifications allow for solutions ra nging from simple board-to-board interconnect to driving two connectors across a backplane. a single r eceiver specification is given that accepts signals from both the short run and long run transmitter specifications. the short run transmitter should be used mainly for chip-to-chip connections on either the same printed circuit board or across a single connector. this covers the case where connections are made to a mezzanine (daughter) card. the minimum swings of the short run specification reduce the overall power used by the transceivers. the long run transmitter specifications use larger voltage swings that are capable of driving signals across backplanes. this allows a user to drive signals acr oss two connectors and a backplane. the specifications allow a distance of at least 50 cm at all baud rates. all unit intervals are specified with a toleranc e of +/? 100 ppm. the worst case frequency difference between any transmit and receive clock is 200 ppm.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 91 serial rapidio to ensure interoperability between drivers and receivers of different vendors and technologies, ac coupling at the receiver input must be used. 17.1 dc requirements for serial rapidio sd1_ref_clk and sd1_ref_clk for more information, see section 15.2, ?serdes reference clocks.? 17.2 ac requirements for serial rapidio sd1_ref_clk and sd1_ref_clk figure 63 lists the ac requirements. 17.3 equalization with the use of high speed serial links, the interconn ect media causes degradation of the signal at the receiver. effects such as inter-symbol interference (i si) or data dependent jitter are produced. this loss can be large enough to degrade the eye opening at the r eceiver beyond what is allowed in the specification. to negate a portion of these effects, equalization can be used. the most common equalization techniques that can be used are as follows: ? a passive high pass filter network placed at the receiver. this is often referred to as passive equalization. ? the use of active circuits in the receiver. this is often referred to as adaptive equalization. 17.4 explanatory note on transmitter and receiver specifications ac electrical specifications are given for transmitter and receiver. long run and short run interfaces at three baud rates (a total of six cases) are described. the parameters for the ac electrical specifications are guided by the xaui electrical interface specified in clause 47 of ieee 802.3ae-2002. xaui has similar application goals to serial rapidio, as described in section 8.1. the goal of this standard is that electrical designs for serial rapidio can reuse electrical designs for xaui, suitably modified for applications at the baud intervals and reaches described herein. table 63. sd n _ref_clk and sd n _ref_clk ac requirements symbol parameter description min typical max units comments t ref refclk cycle time ? 10(8) ? ns 8 ns applies only to serial rapidio with 125-mhz reference clock t refcj refclk cycle-to-cycle jitter. difference in the period of any two adjacent refclk cycles ??80ps ? t refpj phase jitter. deviation in edge location with respect to mean edge location ?40 ? 40 ps ?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 92 freescale semiconductor serial rapidio 17.5 transmitter specifications lp-serial transmitter electrical and timing specifications are stated in the text and tables of this section. the differential return loss, s11, of the transmitter in each case shall be better than ? ?10 db for (baud frequency)/10 < freq(f) < 625 mhz, and ? ?10 db + 10log(f/625 mhz) db for 625 mhz freq(f) baud frequency the reference impedance for the differential return loss measurements is 100 ohm resistive. differential return loss includes contributions from on-chip circuitry, chip packaging and any off-chip components related to the driver. the output impedance requirement applies to all valid output levels. it is recommended that the 20%-80% rise/fall time of the transmitter, as measured at the transmitter output, in each case have a minimum value 60 ps. it is recommended that the timing skew at the output of an lp-serial transmitter between the two signals that comprise a differential pair not exceed 25 ps at 1.25 gb, 20 ps at 2.50 gb and 15 ps at 3.125 gb. table 64. short run transmitter ac timing specifications?1.25 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 500 1000 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ? multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 800 800 ps +/- 100 ppm table 65. short run transmitter ac timing specifications?2.5 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 500 1000 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 93 serial rapidio multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 400 400 ps +/- 100 ppm table 66. short run transmitter ac timing specifications?3.125 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 500 1000 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ? multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 320 320 ps +/? 100 ppm table 67. long run transmitter ac timing specifications?1.25 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 800 1600 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ? multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 800 800 ps +/- 100 ppm table 65. short run transmitter ac timing specifications?2.5 gbaud (continued) characteristic symbol range unit notes min max
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 94 freescale semiconductor serial rapidio for each baud rate at which an lp-serial transmitter is specified to operate, the output eye pattern of the transmitter shall fall entirely within the unshaded portion of the transmitter output compliance mask shown in figure 58 with the parameters specified in figure 70 when measured at the output pins of the device and the device is driving a 100 +/?5% differential resistive load. the output eye pattern of an lp-serial transmitter that implements pre-emphasis (to equalize the link and reduce inter-symbol interference) need only comply with the transmitter output compliance mask when pre-emphasis is disabled or minimized. table 68. long run transmitter ac timing specifications?2.5 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 800 1600 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ? multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 400 400 ps +/- 100 ppm table 69. long run transmitter ac timing specifications?3.125 gbaud characteristic symbol range unit notes min max output voltage, v o ?0.40 2.30 volts voltage relative to common of either signal comprising a differential pair differential output voltage v diffpp 800 1600 mv p-p ? deterministic jitter j d ? 0.17 ui p-p ? total jitter j t ? 0.35 ui p-p ? multiple output skew s mo ? 1000 ps skew at the transmitter output between lanes of a multilane link unit interval ui 320 320 ps +/- 100 ppm
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 95 serial rapidio figure 58. transmitter output compliance mask 17.6 receiver specifications lp-serial receiver electrical and timing specifications are stated in the text and tables of this section. receiver input impedance shall result in a differential return loss better that 10 db and a common mode return loss better than 6 db from 100 mhz to (0.8) (baud frequency). this includes contributions from on-chip circuitry, the chip package and any off-chi p components related to the receiver. ac coupling components are included in this requirement. the refe rence impedance for return loss measurements is 100 ohm resistive for differential return loss and 25- resistive for common mode. table 70. transmitter differential output eye diagram parameters transmitter type v diff min (mv) v diff max (mv) a (ui) b (ui) 1.25 gbaud short range 250 500 0.175 0.39 1.25 gbaud long range 400 800 0.175 0.39 2.5 gbaud short range 250 500 0.175 0.39 2.5 gbaud long range 400 800 0.175 0.39 3.125 gbaud short range 250 500 0.175 0.39 3.125 gbaud long range 400 800 0.175 0.39 0 v diff min v diff max -v diff min -v diff max 0b 1 - b1 time in ui transmitter differential output voltage a1 - a
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 96 freescale semiconductor serial rapidio table 71. receiver ac timing specifications?1.25 gbaud characteristic symbol range unit notes min max differential input voltage v in 200 1600 mv p-p measured at receiver deterministic jitter tolerance j d 0.37 ? ui p-p measured at receiver combined deterministic and random jitter tolerance j dr 0.55 ? ui p-p measured at receiver total jitter tolerance 1 j t 0.65 ? ui p-p measured at receiver multiple input skew s mi ? 24 ns skew at the receiver input between lanes of a multilane link bit error rate ber ? 10 ?12 ?? unit interval ui 800 800 ps +/? 100 ppm note: 1. total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. th e sinusoidal jitter may have any amplitude and frequency in the unshaded region of figure 59 . the sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects. table 72. receiver ac timing specifications?2.5 gbaud characteristic symbol range unit notes min max differential input voltage v in 200 1600 mv p-p measured at receiver deterministic jitter tolerance j d 0.37 ? ui p-p measured at receiver combined deterministic and random jitter tolerance j dr 0.55 ? ui p-p measured at receiver total jitter tolerance 1 j t 0.65 ? ui p-p measured at receiver multiple input skew s mi ? 24 ns skew at the receiver input between lanes of a multilane link bit error rate ber ? 10 ?12 ?? unit interval ui 400 400 ps +/? 100 ppm note: 1. total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. th e sinusoidal jitter may have any amplitude and frequency in the unshaded region of figure 59 . the sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 97 serial rapidio figure 59. single frequency sinusoidal jitter limits table 73. receiver ac timing specifications?3.125 gbaud characteristic symbol range unit notes min max differential input voltage v in 200 1600 mv p-p measured at receiver deterministic jitter tolerance j d 0.37 ? ui p-p measured at receiver combined deterministic and random jitter tolerance j dr 0.55 ? ui p-p measured at receiver total jitter tolerance 1 j t 0.65 ? ui p-p measured at receiver multiple input skew s mi ? 22 ns skew at the receiver input between lanes of a multilane link bit error rate ber ? 10 -12 ?? unit interval ui 320 320 ps +/- 100 ppm note: 1. total jitter is composed of three components, deterministic jitter, random jitter and single frequency sinusoidal jitter. th e sinusoidal jitter may have any amplitude and frequency in the unshaded region of figure 59 . the sinusoidal jitter component is included to ensure margin for low frequency jitter, wander, noise, crosstalk and other variable system effects. 8.5 ui p-p 0.10 ui p-p sinusoidal jitter amplitude 22.1 khz 1.875 mhz 20 mhz frequency
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 98 freescale semiconductor serial rapidio 17.7 receiver eye diagrams for each baud rate at which an lp-serial receiver is specified to operate, the receiver shall meet the corresponding bit error rate specification ( table 71 , table 72 , and table 73 ) when the eye pattern of the receiver test signal (exclusive of sinusoidal jitter) falls entirely within the unshaded portion of the receiver input compliance mask shown in figure 60 with the parameters specified in table 74 . the eye pattern of the receiver test signal is measured at the input pins of the receiving device with the device replaced with a 100- +/? 5% differential resistive load. figure 60. receiver input compliance mask 17.8 measurement and test requirements because the lp-serial electrical specification are guided by the xaui electrical interface specified in clause 47 of ieee 802.3ae-2002, the measurement and test requirements defined here are similarly guided table 74. receiver input compliance mask parameters exclusive of sinusoidal jitter receiver type v diff min (mv) v diff max (mv) a (ui) b (ui) 1.25 gbaud 100 800 0.275 0.400 2.5 gbaud 100 800 0.275 0.400 3.125 gbaud 100 800 0.275 0.400 1 0 v diff max -v diff max v diff min -v diff min time (ui) receiver differential input voltage 0 ab 1-b1-a
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 99 serial rapidio by clause 47. additionally, the cjpat test patte rn defined in annex 48a of ieee 802.3ae-2002 is specified as the test pattern for use in eye pattern and jitter measurements. annex 48b of ieee 802.3ae-2002 is recommended as a reference for additional information on jitter test methods. 17.8.1 eye template measurements for the purpose of eye template measurements, the effects of a single-pole high pass filter with a 3 db point at (baud frequency)/1667 is applied to the jitter. the data pattern fo r template measurements is the continuous jitter test pattern (cjpat) defined in a nnex 48a of ieee 802.3ae. all lanes of the lp-serial link shall be active in both the transmit and receive directions, and opposite ends of the links shall use asynchronous clocks. four lane imple mentations shall use cjpat as defined in annex 48a. single lane implementations shall use the cjpat sequence specifi ed in annex 48a for transmission on lane 0. the amount of data represented in the eye shall be adequate to ensure that the bit error ratio is less than 10 -12 . the eye pattern shall be measured with ac coupling and the compliance template centered at 0 volts differential. the left and right edges of the template shall be aligned with the mean zero crossing points of the measured data eye. the load for this test shall be 100 resistive +/? 5% differential to 2.5 ghz. 17.8.2 jitter test measurements for the purpose of jitter measurement, the effects of a si ngle-pole high pass filter with a 3 db point at (baud frequency)/1667 is applied to the jitte r. the data pattern for jitter measurements is the continuous jitter test pattern (cjpat) pattern defined in annex 48a of ieee 802.3ae. al l lanes of the lp-serial link shall be active in both the transmit and receive directions , and opposite ends of the links shall use asynchronous clocks. four lane implementations shall use cjpat as defined in annex 48a. si ngle lane implementations shall use the cjpat sequence specified in annex 48a fo r transmission on lane 0. jitter shall be measured with ac coupling and at 0 volts differential. jitter measurement for the transmitter (or for calibration of a jitter tolerance setup) shall be performed with a test procedure resulting in a ber curve such as that described in annex 48b of ieee 802.3ae. 17.8.3 transmit jitter transmit jitter is measured at the driver output when terminated into a load of 100 resistive +/? 5% differential to 2.5 ghz. 17.8.4 jitter tolerance jitter tolerance is measured at the receiver using a jitte r tolerance test signal. this signal is obtained by first producing the sum of deterministic and random jitter de fined in section 8.6 and then adjusting the signal amplitude until the data eye contacts the 6 points of the minimum eye opening of the receive template shown in figure 8-4 and table 8-11. note that for this to occur, the test signal must have vertical waveform symmetry about the average value and have horizontal symmetry (including jitter) about the mean zero crossing. eye template measurement requirements are as defined above. random jitter is calibrated using a high pass filter with a low frequency corner at 20 mhz and a 20 db/decade roll-off below this. the required sinusoidal jitter specified in section 8.6 is then added to the signal and the test load is replaced by the receiver being tested.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 100 freescale semiconductor package description 18 package description this section describes package parame ters, pin assignments, and dimensions. 18.1 package parameters for the MPC8572E fc-pbga the package parameters are as provided in the following list. the package type is 33 mm 33 mm, 1023 flip chip plastic ball grid array (fc-pbga). package outline 33 mm 33 mm interconnects 1023 ball pitch 1 mm ball diameter (typical) 0.6 mm solder balls 63% sn 37% pb solder balls (lead-free) 96.5% sn 3.5% ag
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 101 package description 18.2 mechanical dimensions of the MPC8572E fc-pbga figure 61 shows the preliminary mechanical dimensions of the MPC8572E fc-pbga package with full lid. this is subject to change. figure 61. mechanical dimensions of the MPC8572E fc-pbga with full lid notes: 1. all dimensions are in millimeters. 2. dimensions and tolerances per asme y14.5m-1994. 3. all dimensions are symmetric across the package center lines unless dimensioned otherwise. 4. maximum solder ball diameter measured parallel to datum a. 5. datum a, the seating plane, is determined by the spherical crowns of the solder balls. 6. parallelism measurement shall exclude any effect of mark on top surface of package.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 102 freescale semiconductor package description 18.3 pinout listings table 75 provides the preliminary pin-out listing for the MPC8572E 1023 fc-pbga package. this table is included for preliminary information purposes only. table 75. MPC8572E pinout listing signal signal name package pin number pin type power supply notes ddr sdram memory interface 1 d1_mdq[0:63] data d15, a14, b12, d12, a15, b15, b13, c13, c11, d11, d9, a8, a12, a11, a9, b9, f11, g12, k11, k12, e10, e9, j11, j10, g8, h10, l10, m11, f10, g9, k9, k8, ac6, ac7, ag8, ah9, ab6, ab8, ae9, af9, al8, am8, am10, ak11, ah8, ak8, aj10, ak10, al12, aj12, al14, ak14, al11, am11, ak13, am14, am15, aj16, al18, am18, aj15, al15, ak17, am17 i/o gv dd ? d1_mecc[0:7] error correcting code m10, m7, r8, t11, l12, l11, p9, r10 i/o gv dd ? d1_mapar_err address parity error p6 i gv dd ? d1_mapar_out address parity out w6 o gv dd ? d1_mdm[0:8] data mask c14, a10, g11, h9, ad7, aj9, am12, ak16, n11 ogv dd ? d1_mdqs[0:8] data strobe a13, c10, h12, j7, ae8, am9, am13, al17, n9 i/o gv dd ? d1_mdqs [0:8] data strobe d14, b10, h13, j8, ad8, al9, aj13, am16, p10 i/o gv dd ? d1_ma[0:15] address y7, w8, u6, w9, u7, v8, y11, v10, t6, v11, aa10, u9, u10, ad11, t8, p7 ogv dd ? d1_mba[0:2] bank select aa7, aa8, r7 o gv dd ? d1_mwe write enable ac12 o gv dd ? d1_mcas column address strobe ac9 o gv dd ? d1_mras row address strobe ab12 o gv dd ?
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 103 package description d1_mcke[0:3] clock enable m8, l9, t9, n8 o gv dd 11 d1_mcs [0:3] chip select ab9, af10, ab11, ae11 ogv dd ? d1_mck[0:5] clock v7, e13, ah11, y9, f14, ag10 ogv dd ? d1_mck [0:5] clock complements y10, e12, ah12, aa11, f13, ag11 ogv dd ? d1_modt[0:3] on die termination ad10, af12, ac10, ae12 ogv dd ? d1_mdic[0:1] driver impedance calibration e15, g14 i/o gv dd 25 ddr sdram memory interface 2 d2_mdq[0:63] data a6, b7, c5, d5, a7, c8, d8, d6, c4, a3, d3, d2, b4, a4, b1, c1, e3, e1, g2, g6, d1, e4, g5, g3, j4, j2, p4, r5, h3, h1, n5, n3, y6, y4, ac3, ad2, v5, w5, ab2, ab3, ad5, ae3, af6, ag7, ac4, ad4, af4, af7, ah5, aj1, al2, am3, ah3, ah6, am1, al3, ak5, al5, aj7, ak7, ak4, am4, al6, am7 i/o gv dd ? d2_mecc[0:7] error correcting code j5, h7, l7, n6, h4, h6, m4, m5 i/o gv dd ? d2_mapar_err address parity error n1 i gv dd ? d2_mapar_out address parity out w2 o gv dd ? d2_mdm[0:8] data mask a5, b3, f4, j1, aa4, ae5, ak1, am5, k5 ogv dd ? d2_mdqs[0:8] data strobe b6, c2, f5, l4, ab5, af3, al1, am6, l6 i/o gv dd ? d2_mdqs [0:8] data strobe c7, a2, f2, k3, aa5, ae6, ak2, aj6, k6 i/o gv dd ? d2_ma[0:15] address w1, u4, u3, t1, t2, t3, r1, r2, t5, r4, y3, p1, n2, af1, m2, m1 ogv dd ? d2_mba[0:2] bank select y1, w3, p3 o gv dd ? d2_mwe write enable aa2 o gv dd ? d2_mcas column address strobe ad1 o gv dd ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 104 freescale semiconductor package description d2_mras row address strobe aa1 o gv dd ? d2_mcke[0:3] clock enable l3, l1, k1, k2 o gv dd 11 d2_mcs [0:3] chip select ab1, ag2, ac1, ah2 o gv dd ? d2_mck[0:5] clock v4, f7, aj3, v2, e7, ag4 ogv dd ? d2_mck [0:5] clock complements v1, f8, aj4, u1, e6, ag5 ogv dd ? d2_modt[0:3] on die termination ae1, ag1, ae2, ah1 o gv dd ? d2_mdic[0:1] driver impedance calibration f1, g1 i/o gv dd 25 local bus controller interface lad[0:31] muxed data/address m22, l22, f22, g22, f21, g21, e20, h22, k22, k21, h19, j20, j19, l20, m20, m19, e22, e21, l19, k19, g19, h18, e18, g18, j17, k17, k14, j15, h16, j14, h15, g15 i/o bv dd 34 ldp[0:3] data parity m21, d22, a24, e17 i/o bv dd ? la[27] burst address j21 o bv dd 5, 9 la[28:31] port address f20, k18, h20, g17 o bv dd 5, 7, 9 lcs [0:4] chip selects b23, e16, d20, b25, a22 obv dd 10 lcs [5]/dma2_dreq [1] chip selects / dma request d19 i/o bv dd 1, 10 lcs [6]/dma2_dack [1] chip selects / dma ack e19 o bv dd 1, 10 lcs [7]/dma2_ddone [1] chip selects / dma done c21 o bv dd 1, 10 lwe [0]/lbs[0]/ lfwe write enable / byte select d17 o bv dd 5, 9 lwe [1]/lbs[1] write enable / byte select f15 o bv dd 5, 9 lwe[2] /lbs[2] write enable / byte select b24 o bv dd 5, 9 lwe[3] /lbs[3] write enable / byte select d18 o bv dd 5, 9 lale address latch enable f19 o bv dd 5, 8, 9 lbctl buffer control l18 o bv dd 5, 8, 9 lgpl0/lfcle upm general purpose line 0 / flash command latch enable j13 o bv dd 5, 9 lgpl1/lfale upm general purpose line 1/ flash address latch enable j16 o bv dd 5, 9 table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 105 package description lgpl2/loe /lfre upm general purpose line 2 / output enable / flash read enable a27 o bv dd 5, 8, 9 lgpl3/lfwp upm general purpose line 3 / flash write protect k16 o bv dd 5, 9 lgpl4/lgta /lupwait/lpbse /lfrb upm general purpose line 4 / target ack / wait / parity byte select / flash ready-busy l17 i/o bv dd ? lgpl5 upm general purpose line 5 / amux b26 o bv dd 5, 9 lclk[0:2] local bus clock f17, f16, a23 o bv dd ? lsync_in local bus dll synchronization b22 i bv dd ? lsync_out local bus dll synchronization a21 o bv dd ? dma dma1_dack [0:1] dma acknowledge w25, u30 o ov dd 21 dma2_dack [0] dma acknowledge aa26 o ov dd 5, 9 dma1_dreq [0:1] dma request y29, v27 i ov dd ? dma2_dreq [0] dma request v29 i ov dd ? dma1_ddone [0:1] dma done y28, v30 o ov dd 5, 9 dma2_ddone [0] dma done aa28 o ov dd 5, 9 dma2_dreq [2] dma request m23 i bv dd ? programmable interrupt controller ude0 unconditional debug event processor 0 ac25 i ov dd ? ude1 unconditional debug event processor 1 aa25 i ov dd ? mcp0 machine check processor 0 m28 i ov dd ? mcp1 machine check processor 1 l28 i ov dd ? irq[0:11] external interrupts t24, r24, r25, r27, r28, ab27, ab28, p27, r30, ac28, r29, t31 iov dd ? irq_out interrupt output u24 o ov dd 2, 4 1588 tsec_1588_clk clock in am22 i lv dd ? tsec_1588_trig_in trigger in am23 i lv dd ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 106 freescale semiconductor package description tsec_1588_trig_out trigger out aa23 o lv dd 5, 9 tsec_1588_clk_out clock out ac23 o lv dd 5, 9 tsec_1588_pulse_out1 pulse out1 aa22 o lv dd 5, 9 tsec_1588_pulse_out2 pulse out2 ab23 o lv dd 5, 9 ethernet management interface 1 ec1_mdc management data clock al30 o lv dd 5, 9 ec1_mdio management data in/out am25 i/o lv dd ? ethernet management interface 3 ec3_mdc management data clock af19 o tv dd 5, 9 ec3_mdio management data in/out af18 i/o tv dd ? ethernet management interface 5 ec5_mdc management data clock af14 o tv dd 21 ec5_mdio management data in/out af15 i/o tv dd ? gigabit ethernet reference clock ec_gtx_clk125 reference clock am24 i lv dd 32 three-speed ethernet controller 1 tsec1_rxd[7:0]/fifo1_rxd[ 7:0] receive data am28, al28, am26, ak23, am27, ak26, al29, am30 ilv dd 1 tsec1_txd[7:0]/fifo1_txd[ 7:0] transmit data ac20, ad20, ae22, ab22, ac22, ad21, ab21, ae21 olv dd 1, 5, 9 tsec1_col/fifo1_tx_fc collision detect/flow control aj23 i lv dd 1 tsec1_crs/fifo1_rx_fc carrier sense/flow control am31 i/o lv dd 1, 16 tsec1_gtx_clk transmit clock out ak27 o lv dd tsec1_rx_clk/fifo1_rx_c lk receive clock al25 i lv dd 1 tsec1_rx_dv/fifo1_rx_dv /fifo1_rxc[0] receive data valid al24 i lv dd 1 tsec1_rx_er/fifo1_rx_e r/fifo1_rxc[1] receive data error am29 i lv dd 1 tsec1_tx_clk/fifo1_tx_c lk transmit clock in ab20 i lv dd 1 table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 107 package description tsec1_tx_en/fifo1_tx_en /fifo1_txc[0] transmit enable aj24 o lv dd 1, 22 tsec1_tx_er/fifo1_tx_er r/fifo1_txc[1] transmit error ak25 o lv dd 1, 5, 9 three-speed ethernet controller 2 tsec2_rxd[7:0]/fifo2_rxd[ 7:0]/fifo1_rxd[15:8] receive data ag22, ah20, al22, ag20, ak21, ak22, aj21, ak20 ilv dd 1 tsec2_txd[7:0]/fifo2_txd[ 7:0]/fifo1_txd[15:8] transmit data ah21, af20, ac17, af21, ad18, af22, ae20, ab18 olv dd 1, 5, 9, 24 tsec2_col/fifo2_tx_fc collision detect/flow control ae19 i lv dd 1 tsec2_crs/fifo2_rx_fc carrier sense/flow control aj20 i/o lv dd 1, 16 tsec2_gtx_clk transmit clock out ae18 o lv dd ? tsec2_rx_clk/fifo2_rx_c lk receive clock al23 i lv dd 1 tsec2_rx_dv/fifo2_rx_dv /fifo1_rxc[2] receive data valid aj22 i lv dd 1 tsec2_rx_er/fifo2_rx_e r receive data error ad19 i lv dd 1 tsec2_tx_clk/fifo2_tx_c lk transmit clock in ac19 i lv dd 1 tsec2_tx_en/fifo2_tx_en /fifo1_txc[2] transmit enable ab19 o lv dd 1, 22 tsec2_tx_er/fifo2_tx_er r transmit error ab17 o lv dd 1, 5, 9 three-speed ethernet controller 3 tsec3_txd[3:0]/fec_txd[3: 0]/fifo3_txd[3:0] transmit data ag18, ag17, ah17, ah19 otv dd 1, 5, 9 tsec3_rxd[3:0]/fec_rxd[3: 0]/fifo3_rxd[3:0] receive data ag16, ak19, ad16, aj19 itv dd 1 tsec3_gtx_clk transmit clock out ae17 o tv dd tsec3_rx_clk/fec_rx_cl k/fifo3_rx_clk receive clock af17 i tv dd 1 tsec3_rx_dv/fec_rx_dv/f ifo3_rx_dv receive data valid ag14 i tv dd 1 tsec3_rx_er/fec_rx_er/ fifo3_rx_er receive error ah15 i tv dd 1 table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 108 freescale semiconductor package description tsec3_tx_clk/fec_tx_cl k/fifo3_tx_clk transmit clock in af16 i tv dd 1 tsec3_tx_en/fec_tx_en/f ifo3_tx_en transmit enable aj18 o tv dd 1, 22 three-speed ethernet controller 4 tsec4_txd[3:0]/tsec3_txd[ 7:4]/fifo3_txd[7:4] transmit data ad15, ac16, ac14, ab16 otv dd 1, 5, 9 tsec4_rxd[3:0]/tsec3_rxd [7:4]/fifo3_rxd[7:4] receive data ae15, af13, ae14, ah14 itv dd 1 tsec4_gtx_clk transmit clock out ab14 o tv dd ? tsec4_rx_clk/tsec3_col/ fec_col/fifo3_tx_fc receive clock ag13 i tv dd 1 tsec4_rx_dv/tsec3_crs/ fec_crs/fifo3_rx_fc receive data valid ad13 i/o tv dd 1, 23 tsec4_tx_en/tsec3_tx_e r/fec_tx_er/fifo3_tx_er transmit enable ab15 o tv dd 1, 22 duart uart_cts [0:1] clear to send w30, y27 i ov dd ? uart_rts [0:1] ready to send w31, y30 o ov dd 5, 9 uart_sin[0:1] receive data y26, w29 i ov dd ? uart_sout[0:1] transmit data y25, w26 o ov dd 5, 9 i 2 c interface iic1_scl serial clock ac30 i/o ov dd 4, 20 iic1_sda serial data ab30 i/o ov dd 4, 20 iic2_scl serial clock ad30 i/o ov dd 4, 20 iic2_sda serial data ad29 i/o ov dd 4, 20 serdes (x10) pcie, srio sd1_rx[7:0] receive data (positive) p32, n30, m32, l30, g30, f32, e30, d32 ixv dd_sr ds1 ? sd1_rx [7:0] receive data (negative) p31, n29, m31, l29, g29, f31, e29, d31 ixv dd_sr ds1 ? sd1_tx[7] pcie1 tx data lane 7 / srio or pcie2 tx data lane 3 / pcie3 tx data lane 1 m26 o xv dd_sr ds1 ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 109 package description sd1_tx[6] pcie1 tx data lane 6 / srio or pcie2 tx data lane 2 / pcie3 tx data lane 0 l24 o xv dd_sr ds1 ? sd1_tx[5] pcie1 tx data lane 5 / srio or pcie2 tx data lane 1 k26 o xv dd_sr ds1 ? sd1_tx[4] pcie1 tx data lane 4 / srio or pcie2 tx data lane 0 j24 o xv dd_sr ds1 ? sd1_tx[3] pcie1 tx data lane 3 g24 o xv dd_sr ds1 ? sd1_tx[2] pcie1 tx data lane 2 f26 o xv dd_sr ds1 ? sd1_tx[1] pcie1 tx data lane 1] e24 o xv dd_sr ds1 ? sd1_tx[0] pcie1 tx data lane 0 d26 o xv dd_sr ds1 ? sd1_tx [7:0] transmit data (negative) m27, l25, k27, j25, g25, f27, e25, d27 oxv dd_sr ds1 ? sd1_pll_tpd pll test point digital j32 o xv dd_sr ds1 17 sd1_ref_clk pll reference clock h32 i xv dd_sr ds1 ? sd1_ref_clk pll reference clock complement h31 i xv dd_sr ds1 ? reserved ? c29, k32 ? ? 26 reserved ? c30, k31 ? ? 27 reserved ? c24, c25, h26, h27 ? ? 28 reserved ? al20, al21 ? ? 29 serdes (x4) sgmii sd2_rx[3:0] receive data (positive) ak32, aj30, af30, ae32 ixv dd_sr ds2 ? sd2_rx [3:0] receive data (negative) ak31, aj29, af29, ae31 ixv dd_sr ds2 ? sd2_tx[3] sgmii tx data etsec4 ah26 o xv dd_sr ds2 ? sd2_tx[2] sgmii tx data etsec3 ag24 o xv dd_sr ds2 ? sd2_tx[1] sgmii tx data etsec2 ae24 o xv dd_sr ds2 ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 110 freescale semiconductor package description sd2_tx[0] sgmii tx data etsec1 ad26 o xv dd_sr ds2 ? sd2_tx [3:0] transmit data (negative) ah27, ag25, ae25, ad27 oxv dd_sr ds2 ? sd2_pll_tpd pll test point digital ah32 o xv dd_sr ds2 17 sd2_ref_clk pll reference clock ag32 i xv dd_sr ds2 ? sd2_ref_clk pll reference clock complement ag31 i xv dd_sr ds2 ? reserved ? af26, af27 ? ? 28 general-purpose input/output gpinout[0:7] general purpose input / output b27, a28, b31, a32, b30, a31, b28, b29 i/o bv dd ? system control hreset hard reset ac31 i ov dd ? hreset_req hard reset request l23 o ov dd 21 sreset soft reset p24 i ov dd ? ckstp_in0 checkstop in processor 0 n26 i ov dd ? ckstp_in1 checkstop in processor 1 n25 i ov dd ? ckstp_out0 checkstop out processor 0 u29 o ov dd 2, 4 ckstp_out1 checkstop out processor 1 t25 o ov dd 2, 4 debug trig_in trigger in p26 i ov dd ? trig_out/ready_p0/quies ce trigger out / ready processor 0/ quiesce p25 o ov dd 21 ready_p1 ready processor 1 n28 o ov dd 5, 9 msrcid[0:1] memory debug source port id u27, t29 o ov dd 5, 9, 30 msrcid[2:4] memory debug source port id u28, w24, w28 o ov dd 21 mdval memory debug data valid v26 o ov dd 2, 21 clk_out clock out u32 o ov dd 11 clock rtc real time clock v25 i ov dd ? sysclk system clock y32 i ov dd ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 111 package description ddrclk ddr clock aa29 i ov dd 31 jtag tck test clock t28 i ov dd tdi test data in t27 i ov dd 12 tdo test data out t26 o ov dd 11 tms test mode select u26 i ov dd 12 trst test reset aa32 i ov dd 12 dft l1_tstclk l1 test clock v32 i ov dd 18 l2_tstclk l2 test clock v31 i ov dd 18 lssd_mode lssd mode n24 i ov dd 18 test_sel test select 0 k28 i ov dd 18 power management asleep asleep p28 o ov dd 9, 15, 21 table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 112 freescale semiconductor package description power and ground signals gnd ground a18, a25, a29, c3, c6, c9, c12, c15, c20, c22, e5, e8, e11, e14, f3, g7, g10, g13, g16, h5, h21, j3, j9, j12, j18, k7, l5, l13, l15, l16, l21, m3, m9, m12, m14, m16, m18, n7, n13, n15, n17, n19, n21, n23, p5, p12, p14, p16, p20, p22, r3, r9, r11, r13, r15, r17, r19, r21, r23, r26, t7, t12, t14, t16, t18, t20, t22, t30, u5, u11, u13, u15, u16, u17, u19, u21, u23, u25, v3, v9, v12, v14, v16, v18, v20, v22, w7, w11, w13, w15, w17, w19, w21, w27, w32, y5, y12, y14, y16, y18, y20, aa3, aa9, aa13, aa15, aa17, aa19, aa21, aa30, ab7, ab26, ac5, ac11, ac13, ad3, ad9, ad14, ad17, ad22, ae7, ae13, af5, af11, ag3, ag9, ag15, ag19, ah7, ah13, ah22, aj5, aj11, aj17, ak3, ak9, ak15, ak24, al7, al13, al19, al26 ??? xgnd_srds1 serdes transceiver pad gnd (xpadvss) c23, c27, d23, d25, e23, e26, f23, f24, g23, g27, h23, h25, j23, j26, k23, k24, l27, m25 ??? xgnd_srds2 serdes transceiver pad gnd (xpadvss) ad23, ad25, ae23, ae27, af23, af24, ag23, ag26, ah23, ah25, aj27 ??? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 113 package description sgnd_srds1 serdes transceiver core logic gnd (xcorevss) c28, c32, d30, e31, f28, f29, g32, h28, h30, j28, k29, l32, m30, n31, p29, r32 ??? sgnd_srds2 serdes transceiver core logic gnd (xcorevss) ae28, ae30, af28, af32, ag28, ag30, ah28, aj28, aj31, al32 ??? agnd_srds1 serdes pll gnd j31 ? ? ? agnd_srds2 serdes pll gnd ah31 ? ? ? ovdd general i/o supply u31, v24, v28, y31, aa27, ab25, ab29 ?ovdd? lvdd tsec 1&2 i/o supply ac18, ac21, ag21, al27 ?lvdd? tvdd tsec 3&4 i/o supply ac15, ae16, ah18 ? tvdd ? gvdd sstl_1.8 ddr supply b2, b5, b8, b11, b14, d4, d7, d10, d13, e2, f6, f9, f12, g4, h2, h8, h11, h14, j6, k4, k10, k13, l2, l8, m6, n4, n10, p2, p8, r6, t4, t10, u2, u8, v6, w4, w10, y2, y8, aa6, ab4, ab10, ac2, ac8, ad6, ad12, ae4, ae10, af2, af8, ag6, ag12, ah4, ah10, ah16, aj2, aj8, aj14, ak6, ak12, ak18, al4, al10, al16, am2 ?gvdd? bvdd local bus and gpio supply a26, a30, b21, d16, d21, f18, g20, h17, j22, k15, k20 ? bvdd ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 114 freescale semiconductor package description vdd core, l2, logic supply l14, m13, m15, m17, n12, n14, n16, n20, n22, p11, p13, p15, p17, p19, p21, p23, r12, r14, r16, r18, r20, r22, t13, t15, t19, t21, t23, u12, u14, u18, u20, u22, v13, v15, v17, v19, v21, w12, w14, w16, w18, w20, w22, y13, y15, y17, y19, y21, aa12, aa14, aa16, aa18, aa20, ab13 ?vdd? svdd_srds1 serdes core 1 logic supply (xcorevdd) c31, d29, e28, e32, f30, g28, g31, h29, k30, l31, m29, n32, p30 ??? svdd_srds2 serdes core 2 logic supply (xcorevdd) ad32, af31, ag29, aj32, ak29, ak30 ??? xvdd_srds1 serdes1 transceiver supply (xpadvdd) c26, d24, e27, f25, g26, h24, j27, k25, l26, m24, n27 ??? xvdd_srds2 serdes2 transceiver supply (xpadvdd) ad24, ad28, ae26, af25, ag27, ah24, aj26 ??? avdd_lbiu local bus pll supply a19 ? ? 19 avdd_ddr ddr pll supply am20 ? ? 19 avdd_core0 cpu pll supply b18 ? ? 19 avdd_core1 cpu pll supply a17 ? ? 19 avdd_plat platform pll supply ab32 ? ? 19 avdd_srds1 serdes1 pll supply j29 ? ? 19 avdd_srds2 serdes2 pll supply ah29 ? ? 19 sensevdd vdd sensing pin n18 ? ? 13 sensevss gnd sensing pin p18 ? ? 13 analog signals mvref1 sstl_1.8 reference voltage c16 i gv dd /2 ? mvref2 sstl_1.8 reference voltage am19 i gv dd /2 ? sd1_imp_cal_rx serdes1 rx impedance calibration b32 i 200 ( 1%) to gnd ? table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 115 package description sd1_imp_cal_tx serdes1 tx impedance calibration t32 i 100 ( 1%) to gnd ? sd1_pll_tpa serdes1 pll test point analog j30 o avdd_s rds analog 17 sd2_imp_cal_rx serdes2 rx impedance calibration ac32 i 200 ( 1%) to gnd ? sd2_imp_cal_tx serdes2 tx impedance calibration am32 i 100 ( 1%) to gnd ? sd2_pll_tpa serdes2 pll test point analog ah30 o avdd_s rds analog 17 temp_anode temperature diode anode aa31 ? internal diode 14 temp_cathode temperature diode cathode ab31 ? internal diode 14 no connection pins table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 116 freescale semiconductor package description n/c no connection a16, a20, b16, b17, b19, b20, c17, c18, c19, d28, r31, t17, v23, w23, y22, y23, y24, aa24, ab24, ac24, ac26, ac27, ac29, ad31, ae29, aj25, ak28, al31, am21 ??17 note: 1. all multiplexed signals are listed only once and do not re-occur. for example, lcs5/dma_req2 is listed only once in the local bus controller section, and is not mentioned in the dma section even though the pin also functions as dma_req2. 2. recommend a weak pull-up resistor (2?10 k ) be placed on this pin to ovdd. 4. this pin is an open drain signal. 5. this pin is a reset configuration pin. it has a weak internal pull-up p-fet which is enabled only when the processor is in t he reset state. this pull-up is designed such that it can be overpowered by an external 4.7-ko pull-down resistor. however, if the signal is intended to be high after reset, and if there is any device on the net which might pull down the value of the net at reset, then a pullup or active driver is needed. 6. treat these pins as no connects (nc) unless using debug address functionality. 7. the value of la[29:31] during reset sets the ccb clock to sysclk pll ratio. these pins require 4.7-k pull-up or pull-down resistors. see section 19.2, ?ccb/sysclk pll ratio.? 8. the value of lale, lgpl2 and lbctl at reset set the e500 core clock to ccb clock pll ratio. these pins require 4.7-k pull-up or pull-down resistors. see the section 19.3, ?e500 core pll ratio.? 9. functionally, this pin is an output, but structurally it is an i/o because it either samples configuration input during rese t or because it has other manufacturing test functions. this pin therefore be described as an i/o for boundary scan. 10. if this pin is configured for local bus controller usage, recommend a weak pull-up resistor (2-10 k ) be placed on this pin to bvdd, to ensure no random chip select assertion due to possible noise and so on. 11. this output is actively driven during reset rather than being three-stated during reset. 12. these jtag pins have weak internal pull-up p-fets that are always enabled. 13. these pins are connected to the vdd/gnd planes internally and may be used by the core power supply to improve tracking and regulation. 14. internal thermally sensitive diode. 15. if this pin is connected to a device that pulls down during reset, an external pull-up is required to drive this pin to a s afe state during reset. 16. this pin is only an output in fifo mode when used as rx flow control. 17. do not connect. 18. these are test signals for factory use only and must be pulled up (100 - 1 k ) to ovdd for normal machine operation. 19. independent supplies derived from board vdd. 20. recommend a pull-up resistor (~1 k ) be placed on this pin to ovdd. 21. the following pins must not be pulled down during power-on reset: dma1_dack [0:1], ec5_mdc, hreset_req, trig_out/ready_p0/quiesce , msrcid[2:4], mdval, asleep. 22. this pin requires an external 4.7-k pull-down resistor to prevent phy from seeing a valid transmit enable before it is actively driven. 23. this pin is only an output in etsec3 fifo mode when used as rx flow control. 24. tsec2_txd[1] is used as cfg_dram_type. it must be valid at power-up, even before hreset assertion. table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 117 package description 25. when operating in ddr2 mode, connect dn_mdic[0] to ground through 18.2- (full-strength mode) or 36.4- (half-strength mode) precision 1% resistor, and connect dn_mdic[1] to gvdd through 18.2- (full-strength mode) or 36.4- (half-strength mode) precision 1% resistor. when operating in ddr3 mode, connect dn_mdic[0] to ground through 20- (full-strength mode) or 40- (half-strength mode) precision 1% resistor, and connect dn_mdic[1] to gvdd through 20- (full-strength mode) or 40- (half-strength mode) precision 1% resistor. these pins are used for automatic calibration of the ddr ios. 26. these pins should be connected to xvdd_srds1. 27. these pins should be pulled to ground (xgnd_srds1) through a 300- ( 10%) resistor. 28. these pins should be left floating. 29. these pins should be pulled up to tvdd through a 2?10 k resistor. 30. these pins have other manufacturing or debug test functions. it is recommended to add both pull-up resistor pads to ovdd and pull-down resistor pads to gnd on board to support future debug testing when needed. 31. ddrclk input is only required when the MPC8572E ddr controller is running in asynchronous mode. when the ddr controller is configured to run in synchronous mode via por setting cfg_ddr_pll[0:2]=111, the ddrclk input is not required. it is recommended to tie it off to gnd when ddr controller is running in synchronous mode. see the MPC8572E powerquicc? iii integrated host processor family reference manual rev.0, table 4-3 in section 4.2.2 ?clock signals?, section 4.4.3.2 ?ddr pll ratio? and table 4-10 ?ddr complex clock pll ratio? for more detailed description regarding ddr controller operation in asynchronous and synchronous modes. 32. ec_gtx_clk125 is a 125-mhz input clock shared among all etsec ports in the following modes: gmii, tbi, rgmii and rtbi. if none of the etsec ports is operating in these modes, the ec_gtx_clk125 input can be tied off to gnd. 33. these pins should be pulled to ground (gnd). 34. these pins are sampled at por for general purpose configuration use by software. their value has no impact on the functionality of the hardware. table 75. MPC8572E pinout listing (continued) signal signal name package pin number pin type power supply notes
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 118 freescale semiconductor clocking 19 clocking this section describes the pll configuration of the MPC8572E. note that the platform clock is identical to the core complex bus (ccb) clock. 19.1 clock ranges table 76 provides the clocking specifications for both processor cores. the ddr memory controller can run in either synchronous or asynchronous mode. when running in synchronous mode, the memory bus is clocked relative to the platform clock frequency. when running in asynchronous mode, the memory bus is clocked with its own dedicated pll with clock provided on ddrclk input pin. table 77 provides the clocking specifications for the memory bus. table 76. MPC8572E processor core clocking specifications characteristic maximum processor core frequency unit notes 1067 mhz 1200 mhz 1333 mhz 1500 mhz min max min max min max min max e500 core processor frequency 800 1067 800 1200 800 1333 800 1500 mhz 1, 2 ccb frequency 400 533 400 533 400 533 400 600 mhz ddr data rate 400 667 400 667 400 667 400 800 mhz notes : 1. caution: the ccb to sysclk ratio and e500 core to ccb ratio settings must be chosen such that the resulting sysclk frequency, e500 (core) frequency, and ccb frequency do not exceed their respective maximum or minimum operating frequencies. refer to section 19.2, ?ccb/sysclk pll ratio,? section 19.3, ?e500 core pll ratio,? and section 19.4, ?ddr/ddrclk pll ratio,? for ratio settings. 2. the processor core frequency speed bins listed also reflect the maximum platform (ccb) and ddr data rate frequency supported by production test. running ccb and/or ddr data rate higher than the limit shown above, although logically possible via valid clock ratio setting in some condition, is not supported. table 77. memory bus clocking specifications characteristic min max unit notes memory bus clock frequency 200 400 mhz 1, 2, 3, 4 notes: 1. caution: the ccb clock to sysclk ratio and e500 core to ccb clock ratio settings must be chosen such that the resulting sysclk frequency, e500 (core) frequency, and ccb frequency do not exceed their respective maximum or minimum operating frequencies. refer to section 19.2, ?ccb/sysclk pll ratio,? section 19.3, ?e500 core pll ratio,? and section 19.4, ?ddr/ddrclk pll ratio,? for ratio settings. 2. the memory bus clock refers to the MPC8572E memory controllers? dn_mck[0:5] and dn_mck [0:5] output clocks, running at half of the ddr data rate. 3. in synchronous mode, the memory bus clock speed is half the platform clock frequency. in other words, the ddr data rate is the same as the platform (ccb) frequency. if the desired ddr data rate is higher than the platform (ccb) frequency, asynchronous mode must be used. 4. in asynchronous mode, the memory bus clock speed is dictated by its own pll. refer to section 19.4, ?ddr/ddrclk pll ratio.? the memory bus clock speed must be less than or equal to the ccb clock rate which in turn must be less than the ddr data rate.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 119 clocking as a general guideline when selecting the ddr data rate or platform (ccb) frequency, the following procedures can be used: ? start with the processor core frequency selection; ? after the processor core frequency is determin ed, select the platform (ccb) frequency from the limited options listed in table 79 and table 80 ; ? check the ccb to sysclk ratio to verify a valid ratio can be choose from table 78 ; ? if the desired ddr data rate can be same as the ccb frequency, use the synchronous ddr mode; otherwise, if a higher ddr data rate is desire d, use asynchronous mode by selecting a valid ddr data rate to ddrclk ratio from table 81 . note that in asynchronous mode, the ddr data rate must be greater than the platform (ccb) frequenc y. in other words, running ddr data rate lower than the platform (ccb) frequency in asynchronous mode is not supported by MPC8572E. ? verify all clock ratios to ensure that there is no violation to any clock and/or ratio specification. 19.2 ccb/sysclk pll ratio the ccb clock is the clock that drives the e500 core complex bus (ccb), and is also called the platform clock. the frequency of the ccb is set using the following reset signals, as shown in table 78 : ? sysclk input signal ? binary value on la[29:31] at power up note that there is no default for this pll ratio; these signals must be pulled to the desired values. also note that, in synchronous mode, the ddr data rate is the de termining factor in selecting the ccb bus frequency, because the ccb frequency must equal the ddr data rate. in asynchronous mode, the memory bus clock frequency is decoupled from the ccb bus frequency. 19.3 e500 core pll ratio the clock speed for each e500 core can be configured differently, determined by the values of various signals at power up. table 78. ccb clock ratio binary value of la[29:31] signals ccb:sysclk ratio 000 4:1 001 5:1 010 6:1 011 8:1 100 10:1 101 12:1 110 reserved 111 reserved
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 120 freescale semiconductor clocking table 79 describes the clock ratio between e500 core0 a nd the e500 core complex bus (ccb). this ratio is determined by the binary value of lbctl, lale and lgpl2/loe /lfre at power up, as shown in table 79 . table 80 describes the clock ratio between e500 core1 a nd the e500 core complex bus (ccb). this ratio is determined by the binary value of lwe [0]/lbs[0]/lfwe, uart_sout[1], and ready_p1 signals at power up, as shown in table 80 . 19.4 ddr/ddrclk pll ratio the dual ddr memory controller complexes can be synchronous with, or asynchronous to, the ccb, depending on configuration. table 81 describes the clock ratio between the ddr memory controller complexes and the ddr pll reference clock, ddrclk, which is not the memory bus clock. the ddr memory controller complexes clock frequency is equal to the ddr data rate. when synchronous mode is selected, the memory buses are clocked at half the ccb clock rate. the default mode of operation is for the ddr data rate for both dd r controllers to be equal to the ccb clock rate in synchronous mode, or the resulting ddr pll rate in asynchronous mode. in asynchronous mode, the ddr pll rate to ddrclk ratios listed in table 81 reflects the ddr data rate to ddrclk ratio, because the ddr pll rate in asynchronous mode means the ddr data rate resulting from ddr pll output. table 79. e500 core0 to ccb clock ratio binary value of lbctl, lale, lgpl2/loe /lfre signals e500 core0:ccb clock ratio binary value of lbctl, lale, lgpl2/loe /lfre signals e500 core0:ccb clock ratio 000 reserved 100 2:1 001 reserved 101 5:2 (2.5:1) 010 reserved 110 3:1 011 3:2 (1.5:1) 111 7:2 (3.5:1) table 80. e500 core1 to ccb clock ratio binary value of lwe [0]/lbs [0]/ lfwe , uart_sout[1], ready_p1 signals e500 core1:ccb clock ratio binary value of lw e [0]/lbs [0]/ lfwe , uart_sout[1], ready_p1 signals e500 core1:ccb clock ratio 000 reserved 100 2:1 001 reserved 101 5:2 (2.5:1) 010 reserved 110 3:1 011 3:2 (1.5:1) 111 7:2 (3.5:1)
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 121 clocking note that the ddr pll reference clock input, ddrclk, is only required in asynchronous mode. MPC8572E does not support running one ddr contro ller in synchronous mode and the other in asynchronous mode. 19.5 frequency options 19.5.1 platform to sysclk frequency options table 82 shows the expected frequency values for the platform frequency when using the specified ccb clock to sysclk ratio. table 81. ddr clock ratio binary value of tsec_1588_clk_out, tsec_1588_pulse_out1, tsec_1588_pulse_out2 signals ddr:ddrclk ratio 000 3:1 001 4:1 010 6:1 011 8:1 100 10:1 101 12:1 110 14:1 111 synchronous mode table 82. frequency options for platform frequency ccb to sysclk ratio sysclk (mhz) 33.33 41.66 50 66.66 83 100 111 133.33 platform /ccb frequency (mhz) 4 400 444 533 5 415 500 555 6 400 498 600 8 400 533 10 417 500 12 400 500 600
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 122 freescale semiconductor thermal 19.5.2 minimum platform frequency requirements for high-speed interfaces section 4.4.3.6 ?i/o port selection? of the MPC8572E powerquicc? iii integrated host processor family reference manual , describes various high-speed interface configuration options. note that the ccb clock frequency must be considered for prope r operation of such interfaces as described below. for proper pci express operation, the ccb clock fr equency must be greate r than or equal to: see section 21.1.3.2, ?link width? of the MPC8572E powerquicc? iii integrated host processor family reference manual , for pci express interface width details. note that the ?pci express link width? in the above equation refers to the negotiated link width as the result of pci express link training, which may or may not be the same as the link width por selection. for proper serial rapidio operation, the ccb clock frequency must be greater than: see section 20.4, ?1x/4x lp-serial signal descriptions? of the MPC8572E powerquicc? iii integrated host processor family reference manual , for serial rapidio interface width and frequency details. 20 thermal this section describes the preliminary thermal specifica tions of the MPC8572E. this is subject to change. table 83 shows the thermal characteristics for the package, 1023 33x33 fc-pbga. the package uses a 29.6 x 29.6 mm lid that attaches to the substrate. recommended maximum heat sink force is 10 pounds force (45 newton). table 83. package thermal characteristics rating board symbol value unit notes junction to ambient, natural convection single-layer (1s) r ja 15 c/w 1, 2 junction to ambient, natural convection four-layer (2s2p) r ja 11 c/w 1, 3 junction to ambient (at 200 ft./min.) single-layer (1s) r jma 11 c/w 1, 3 junction to ambient (ar 200 ft./min.) four-layer (2s2p) r jma 8 c/w 1, 3 junction to board ? r jb 4 c/w 4 527 mhz pci express link width () 8 ---------------------------------------------------------------------------------------------- 20.80 () serial rapidio interface frequency () serial rapidio link width () 64 -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 123 thermal 20.1 temperature diode the MPC8572E has a temperature diode on the microprocessor that can be used in conjunction with other system temperature monitoring devices (such as analog devices, adt7461?). these devices use the negative temperature coefficient of a diode operated at a constant current to determine the temperature of the microprocessor and its environment. it is re commended that each MPC8572E device be calibrated. the following are the specifications of the on-board temperature diode: v f > 0.40 v v f < 0.90 v operating range 2?300 a diode leakage < 10 na @ 125 c an approximate value of the ideality may be obtained by calibrating the device near the expected operating temperature. ideality factor is defined as the de viation from the ideal diode equation: another useful equation is: where: i fw = forward current i s = saturation current v d = voltage at diode junction to case ? r jc 0.5 c/w 5 notes: 1. junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance 2. per jedec jesd51-2 with the single-layer board (jesd51-3) horizontal. 3. per jedec jesd51-6 with the board (jesd51-7) horizontal. 4. thermal resistance between the die and the printed circuit board per jedec jesd51-8. board temperature is measured on the top surface of the board near the package. 5. thermal resistance between the active surface of the die and the case top surface determined by the cold plate method (mil spec-883, method 1012.1). table 83. package thermal characteristics (continued) rating board symbol value unit notes i fw = i s e ? 1 qv f ___ nkt v h ? v l = n ln kt __ q i h __ i l
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 124 freescale semiconductor thermal v f = voltage forward biased v h = diode voltage while i h is flowing v l = diode voltage while i l is flowing i h = larger diode bias current i l = smaller diode bias current q = charge of electron (1.6 x 10 ?19 c) n = ideality factor (normally 1.0) k = boltzman?s constant (1.38 x 10 ?23 joules/k) t = temperature (kelvins) the ratio of i h to i l is usually selected to be 10:1. the above simplifies to the following: solving for t, the equation becomes: v h ? v l = 1.986 10 ?4 nt nt = v h ? v l __________ 1.986 10 ?4
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 125 system design information 21 system design information this section provides electrical and thermal design recommendations for successful application of the MPC8572E. 21.1 system clocking this device includes seven plls, as follows: 1. the platform pll generates the platform clock from the externally supplied sysclk input. the frequency ratio between the platform and sysclk is selected using the platform pll ratio configuration bits as described in section 19.2, ?ccb/sysclk pll ratio.? 2. there are two core plls whose ratios are individually configurable. each e500 core pll generates the core clock as a slave to the plat form clock. the frequency ratio between the e500 core clock and the platform cloc k is selected using the e500 pll ratio configuration bits as described in section 19.3, ?e500 core pll ratio.? 3. the ddr complex pll generates the clocking for the ddr controllers 4. the local bus pll generates the clock for the local bus. 5. there is a pll for the serdes1 module to be used for pci express and serial rapid io interfaces. 6. there is a pll for the serdes2 module to be used for sgmii interface. 21.2 power supply design 21.2.1 pll power supply filtering each of the plls listed above is provided w ith power through independent power supply pins (av dd _plat, av dd _core0, av dd _core1, av dd _ddr, av dd _lbiu, av dd _srds1 and av dd _srds2 respectively). the av dd level should always be equivalent to v dd , and preferably these voltages are derived directly from v dd through a low frequency filter scheme such as the following. there are a number of ways to reliably provide power to the plls, but the recommended solution is to provide independent filter circuits per pll power supply as illustrated in figure 62 , one to each of the av dd pins. by providing independent filters to each pll the opportunity to cause noise injection from one pll to the other is reduced. this circuit is intended to filter noise in the p lls resonant frequency range from a 500 khz to 10 mhz range. it should be built with surface mount capacitor s with minimum effective series inductance (esl). consistent with the recommendations of dr. howard johnson in high speed digital design: a handbook of black magic (prentice hall, 1993), multiple small capacito rs of equal value are recommended over a single large value capacitor. each circuit should be placed as cl ose as possible to the specific av dd pin being supplied to minimize noise coupled from nearby circuits. it should be possible to route directly from the capacitors to the av dd pin, which is on the periphery of the 1023 fc-pbga footprint, without the inductance of vias.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 126 freescale semiconductor system design information figure 62 shows the pll power supply filter circuits. figure 62. pll power supply filter circuit note it is recommended to have the minimum number of vias in the av dd trace for board layout. for example, zero vias might be possible if the av dd filter is placed on the component side. one via might be possible if it is placed on the opposite of the component side. additionally, all traces for av dd and the filter components should be low impedance, 10 to 15 mils wide and short. this includes traces going to gnd and the supply rails they are filtering. the av dd _srdsn signal provides power for the analog portions of the serdesn pll. to ensure stability of the internal clock, the power supplied to the pll is filtered using a circuit similar to the one shown in following figure. for maximum effectiveness, the filter circuit is placed as closely as possible to the av dd _srdsn ball to ensure it filters out as much noise as possible. the ground connection should be near the av dd _srdsn ball. the 0.003-f capacitor is closest to the ball, followed by the two 2.2 f capacitors, and finally the 1 resistor to the board supply plane. the capacitors are connected from av dd _srdsn to the ground plane. use ceramic chip cap acitors with the highest possible self-resonant frequency. all traces should be kept short, wide and direct. figure 63. serdes pll power supply filter note the following: ?av dd _srdsn should be a filtered version of sv dd _srdsn. ? signals on the serdesn interface are fed from the xv dd _srdsn power plane. 21.3 decoupling recommendations due to large address and data buses, and high operating frequencies, the device can generate transient power surges and high frequency noise in its power suppl y, especially while driving large capacitive loads. this noise must be prevented from reaching other components in the MPC8572E system, and the device itself requires a clean, tightly regulated source of power. therefore, it is recommended that the system designer place at least one decoupling capacitor at each v dd , tv dd , bv dd , ov dd , gv dd , and lv dd pin v dd av dd 2.2 f 2.2 f gnd low esl surface mount capacitors 10 2.2 f 1 0.003 f gnd 1.0 av dd _srdsn 1. an 0805 sized capacitor is recommended for system initial bring-up. sv dd_srdsn 2.2 f 1
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 127 system design information of the device. these decoupling capacitors should receive their power from separate v dd, tv dd , bv dd , ov dd , gv dd , and lv dd , and gnd power planes in the pcb, utilizing short traces to minimize inductance. capacitors may be placed directly under th e device using a standard escape pattern. others may surround the part. these capacitors should have a value of 0.01 or 0.1 f. only ceramic smt (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. additionally, it is recommended that there be several bulk storage capacitors distributed around the pcb, feeding the v dd , tv dd , bv dd , ov dd , gv dd , and lv dd planes, to enable quick recharging of the smaller chip capacitors. these bulk capacitors should ha ve a low esr (equivalent series resistance) rating to ensure the quick response time necessary. they should also be connected to the power and ground planes through two vias to minimize inductance. suggested bulk capacitors?100?330 f (avx tps tantalum or sanyo oscon). 21.4 serdes block power supply decoupling recommendations the serdes1 and serdes2 blocks require a cl ean, tightly regulated source of power (sv dd _srdsn and xv dd _srdsn) to ensure low jitter on transmit and reliable recovery of data in the receiver. an appropriate decoupling sc heme is outlined below. only surface mount technology (smt) capacitors shoul d be used to minimize inductance. connections from all capacitors to power and ground should be done with multiple vias to further reduce inductance. ? first, the board should have at least 10 x 10-nf smt ceramic chip capacitors as close as possible to the supply balls of the device. where the board has blind vias, these capacitors should be placed directly below the chip supply and ground connecti ons. where the board does not have blind vias, these capacitors should be placed in a ring around the device as close to the supply and ground connections as possible. ? second, there should be a 1-f ceramic chip capacitor from each serdes supply (sv dd _srdsn and xv dd _srdsn) to the board ground plane on each side of the device. this should be done for all serdes supplies. ? third, between the device and any serdes voltage regulator there should be a 10-f, low equivalent series resistance (esr) smt tantalum chip capacitor and a 100-f, low esr smt tantalum chip capacitor. this shoul d be done for all serdes supplies. 21.5 connection recommendations to ensure reliable operation, it is highly recommende d to connect unused inputs to an appropriate signal level. all unused active low inputs should be tied to v dd, tv dd , bv dd , ov dd , gv dd , and lv dd , as required. all unused active high inputs should be conne cted to gnd. all nc (no-connect) signals must remain unconnected. power and ground connecti ons must be made to all external v dd, tv dd , bv dd , ov dd , gv dd , and lv dd , and gnd pins of the device. 21.6 pull-up and pull-down resistor requirements the MPC8572E requires weak pull-up resistors (2?10 k is recommended) on open drain type pins including i 2 c pins and mpic interrupt pins.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 128 freescale semiconductor system design information correct operation of the jtag interface requires configuration of a group of system control pins as demonstrated in figure 66 . care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion gives unpredictable results. the following pins must not be pulled down during power-on reset: dma_dack[0:1] , ec5_mdc, hreset_req , trig_out/ready_p0/quiesce , msrcid[2:4], mdval, and asleep. the test_sel pin must be set to a proper state during por configuration. for more details, refer to the pinlist table of the individual device. 21.7 output buffer dc impedance the MPC8572E drivers are characterized over process, voltage, and temperature. for all buses, the driver is a push-pull single-ended driver type (open drain for i 2 c). to measure z 0 for the single-ended drivers, an external resistor is connected from the chip pad to ov dd or gnd. then, the value of each resistor is varied until the pad voltage is ov dd /2 (see figure 64 ). the output impedance is the average of two components, the resistances of the pull-up and pull-down devices. when data is held high, sw1 is closed (sw2 is open) and r p is trimmed until the voltage at the pad equals ov dd /2. r p then becomes the resistance of the pull-up devices. r p and r n are designed to be close to each other in value. then, z 0 = (r p + r n )/2. figure 64. driver impedance measurement ov dd ognd r p r n pad data sw1 sw2
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 129 system design information table 84 summarizes the signal impedance targets. the driver impedances are targeted at minimum v dd , nominal ov dd , 105 c. 21.8 configuration pin muxing the MPC8572E provides the user with power-on configuration options which can be set through the use of external pull-up or pull-down resistors of 4.7 k on certain output pins (see customer visible configuration pins). these pins are generally used as output only pins in normal operation. while hreset is asserted however, these pins are treated as inputs. the value presented on these pins while hreset is asserted, is latched when hreset deasserts, at which time the input receiver is disabled and the i/o circuit takes on its normal function. most of these sampled configuration pins are equipped with an on-chip gated resi stor of approximately 20 k . this value should permit the 4.7-k resistor to pull the configuration pin to a valid logic low level. the pull-up resistor is enabled only during hreset (and for platform /system clocks after hreset deassertion to ensure capture of the reset value). when the input receiver is disabled the pull-up is also, thus allowi ng functional operation of the pin as an output with minimal signal quality or delay disruption. the default va lue for all configuration bits treated this way has been encoded such that a high voltage level puts the de vice into the default state and external resistors are needed only when non-default settings are required by the user. careful board layout with stubless connections to th ese pull-down resistors coupled with the large value of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. the platform pll ratio, ddr complex pll and e500 pl l ratio configuration pins are not equipped with these default pull-up devices. 21.9 jtag configuration signals correct operation of the jtag interface requires configuration of a group of system control pins as demonstrated in figure 66 . care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion gives unpredictable results. boundary-scan testing is enabled through the jtag interface signals. the trst signal is optional in the ieee std 1149.1 specification, but it is provided on all processors built on power architecture technology. the device requires trst to be asserted during power-on reset flow to ensure that the jtag boundary logic does not interfere with normal chip operation. while the tap controller can be forced to the reset table 84. impedance characteristics impedance local bus, ethernet, duart, control, configuration, power management ddr dram symbol unit r n 45 target 18 target (full strength mode) 36 target (half strength mode) z 0 r p 45 target 18 target (full strength mode) 36 target (half strength mode) z 0 note: nominal supply voltages. see ta b l e 1 , t j = 105 c.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 130 freescale semiconductor system design information state using only the tck and tms signals, generally systems assert trst during the power-on reset flow. simply tying trst to hreset is not practical because the jtag interface is also used for accessing the common on-chip processor (cop), which implements the debug interface to the chip. the cop function of these processors allow a remote computer system (typically, a pc with dedicated hardware and debugging software) to access and control the internal operations of the processor. the cop interface connects primarily through the jtag port of the processor, with some additional status monitoring signals. the cop port requires the ability to independently assert hreset or trst to fully control the processor. if the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the cop reset signals must be merged into these signals with logic. the arrangement shown in figure 66 allows the cop port to independently assert hreset or trst , while ensuring that the target can drive hreset as well. the cop interface has a standard header, shown in figure 65 , for connection to the target system, and is based on the 0.025" square-post, 0.100" centered header assembly (often called a berg header). the connector typically has pin 14 removed as a connector key. the cop header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and othe r standard debugger features. an inexpensive option can be to leave the cop header unpopulated until needed. there is no standardized way to number the cop head er; so emulator vendors have issued many different pin numbering schemes. some cop headers are numbere d top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom. still others numbe r the pins counter-clockwise from pin 1 (as with an ic). regardless of the numbering scheme, the signal placement recommended in figure 65 is common to all known emulators. 21.9.1 termination of unused signals if the jtag interface and cop header is not used, freescale recommends the following connections: ?trst should be tied to hreset through a 0 k isolation resistor so that it is asserted when the system reset signal (hreset ) is asserted, ensuring that the jtag scan chain is initialized during the power-on reset flow. freescale recommends that the cop header be designed into the system as shown in figure 66 . if this is not possible, the isolation resistor allows future access to trst in case a jtag interface may need to be wired onto the system in future debug situations. ? no pull-up/pull-down is required for tdi, tms, tdo or tck.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 131 system design information figure 65. cop connector physical pinout 3 13 9 5 1 6 10 15 11 7 16 12 8 4 key no pin 1 2 cop_tdo cop_tdi nc nc cop_trst cop_vdd_sense cop_chkstp_in nc nc gnd cop_tck cop_tms cop_sreset cop_hreset cop_chkstp_out
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 132 freescale semiconductor system design information figure 66. jtag interface connection hreset from target board sources cop_hreset 13 cop_sreset sreset nc 11 cop_vdd_sense 2 6 15 10 10 k 10 k cop_chkstp_in ckstp_in0 8 cop_tms cop_tdo cop_tdi cop_tck tms tdo tdi 9 1 3 4 cop_trst 7 16 2 10 12 (if any) cop header 14 3 notes: 10 k trst 1 10 k 10 k 10 k ckstp_out0 cop_chkstp_out 3 13 9 5 1 6 10 15 11 7 16 12 8 4 key no pin cop connector physical pinout 1 2 nc sreset 2. populate this with a 10 resistor for short-circuit/current-limiting protection. nc ov dd 10 k hreset 1 to fully control the processor as shown here. 1. the cop port and target board should be able to independently assert hreset and trst to the processor signal integrity. tck 4 5 5.this switch is included as a precaution for bsdl testing. the switch should be closed to position a during bsdl testing to position b. 10 k 6 6. asserting sreset causes a machine check interrupt to the e500 cores. 3. t he key location (pin 14) is not physically present on the cop header. 4. although pin 12 is defined as a no-connect, some debug tools may use pin 12 as an additional gnd pin for improved to avoid accidentally asserting the trst line. if bsdl testing is not being performed, this switch should be closed a b 5 10 k ckstp_out1 ckstp_in1
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 133 system design information 21.10 guidelines for high-speed interface termination 21.10.1 serdes 1 interface entirely unused if the high-speed serdes 1 interface is not used at all, the unused pin should be terminated as described in this section. the following pins must be left unconnected (float): ? sd1_tx[7:0] ? sd1_tx [7:0] ? reserved pins c24, c25, h26, h27 the following pins must be connected to xgnd_srds1: ? sd1_rx[7:0] ? sd1_rx [7:0] ? sd1_ref_clk ? sd1_ref_clk pins k32 and c29 must be tied to xv dd _srds1. pins k31 and c30 must be tied to xgnd_srds1 through a 300- resistor. the por configuration pin cfg_srds1_en on tsec2_txd[5] can be used to power down serdes 1 block for power saving. note that both svdd_srds1 and xvdd_srds1 must remain powered. 21.10.2 serdes 1 interface partly unused if only part of the high speed serdes 1 interface pins are used, the remaining high-speed serial i/o pins should be terminated as described in this section. the following pins must be left unconnected (float) if not used: ? sd1_tx[7:0] ? sd1_tx [7:0] ? reserved pins: c24, c25, h26, h27 the following pins must be connected to xgnd_srds1 if not used: ? sd1_rx[7:0] ? sd1_rx [7:0] pins k32 and c29 must be tied to xv dd _srds1. pins k31 and c30 must be tied to xgnd_srds1 through a 300- resistor. 21.10.3 serdes 2 interface (sgmii) entirely unused if the high-speed serdes 2 interface (sgmii) is not used at all, the unused pin should be terminated as described in this section. the following pins must be left unconnected (float):
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 134 freescale semiconductor system design information ? sd2_tx[3:0] ? sd2_tx [3:0] ? reserved pins: af26, af27 the following pins must be connected to xgnd_srds2: ? sd2_rx[3:0] ? sd2_rx [3:0] ? sd2_ref_clk ? sd2_ref_clk the por configuration pin cfg_srds_sgmii_en on uart_rts [1] can be used to power down serdes 2 block for power saving. note that both svdd_srds2 and xvdd_srds2 must remain powered. 21.10.4 serdes 2 interface (sgmii) partly unused if only part of the high speed serdes 2 interface (sgmii) pins are used, the remaining high-speed serial i/o pins should be terminated as described in this section. the following pins must be left unconnected (float): ? sd2_tx[3:0] ? sd2_tx [3:0] ? reserved pins: af26, af27 the following pins must be connected to xgnd_srds2: ? sd2_rx[3:0] ? sd2_rx [3:0]
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 135 ordering information 22 ordering information ordering information for the parts fully covered by this specification document is provided in section 22.1, ?part numbers fully addressed by this document.? 22.1 part numbers fully addressed by this document table 85 and table 86 provides the freescale part numbering nom enclature for the MPC8572E. note that the individual part numbers correspond to a max imum processor core frequency. for available frequencies, contact your local freescale sales office. in addition to the processor frequency, the part numbering scheme also includes an application m odifier which may specify special application conditions. each part number also contains a revision code which refers to the die mask revision number. table 85. part numbering nomenclature - rev 2.1 mpc nnnn e t l pp ffm r product code 1 1 mpc stands for ?qualified.? part identifier security engine temperature power package 2 2 see section 18, ?package description,? for more information on the available package types. processor frequency/ ddr datarate 3 3 processor core frequencies supported by parts addressed by this specification only. not all parts described in this specification support all core frequencies. additionally, parts addressed by part number specifications may support other maximum core frequencies. silicon revision mpc ppc 8572 e = included blank = 0 to 105 c c = ?40 to 105 c blank = standard l=low px = leaded, fc-pbga vt = pb free, fc-pbga avn = 1500 mhz pocessor; 800 mt/s ddr datarate aul = 1333 mhz processor; 667 mt/s ddr datarate at l = 1200 mhz processor; 667 mt/s ddr datarate arl = 1067 mhz processor; 667 mt/s ddr datarate d= ver. 2.1 (svr = 0x80e8_0021) sec included blank = not included d= ver. 2.1 (svr = 0x80e0_0021) sec not included notes:
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 136 freescale semiconductor ordering information 22.2 part marking parts are marked as the example shown in figure 67 . figure 67. part marking for fc-pbga device table 86. part numbering nomenclature - rev 1.1.1 mpc nnnn e t pp ffm r product code 1 1 mpc stands for ?qualified.? part identifier security engine temperature package 2 2 see section 18, ?package description,? for more information on the available package types. processor frequency/ ddr datarate 3 3 processor core frequencies supported by parts addressed by this specification only. not all parts described in this specification support all core frequencies. additionally, parts addressed by part number specifications may support other maximum core frequencies. silicon revision mpc ppc 8572 e = included blank=0 to 105 c c= ?40 to 105 c px = leaded, fc-pbga vt = pb free, fc-pbga avn = 1500 mhz pocessor; 800 mt/s ddr datarate aul = 1333 mhz processor; 667 mt/s ddr datarate at l = 1200 mhz processor; 667 mt/s ddr datarate arl = 1067 mhz processor; 667 mt/s ddr datarate b = ver. 1.1.1 (svr = 0x80e8_0011) sec included blank = not included b = ver. 1.1.1 (svr = 0x80e0_0011) sec not included notes: mmmmm ccccc atwlyyww notes: ccccc is the country of assembly. this space is left blank if parts are assembled in the united states. mmmmm is the 5-digit mask number. atwlyyww is the traceability code. fc-pbga mpc8572xxxxxx
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 137 document revision history table 87 explains line four of figure 67 . 23 document revision history table 88 provides a revision history for the MPC8572E hardware specification. table 87. meaning of last line of part marking digit description a assembly site eoak hill qklm wl lot number yy year assembled ww work week assembled table 88. document revision history rev. number date substantive change(s) 4 06/2010 ? in section 18.3, ?pinout listings,? updated ta b l e 7 5 showing gpinout power rail as bvdd. ? updated section 14.1, ?gpio dc electrical characteristics.? 3 03/2010 ? in section 2.1, ?overall dc electrical characteristics ,? changed gpio power from ovdd to bvdd. ?in section 22.1, ?part numbers fully addressed by this document,? added ta b l e 8 5 for rev 2.1 silicon. ?in section 22.1, ?part numbers fully addressed by this document,? updated ta b l e 8 6 for rev 1.1.1 silicon. 2 06/2009 ? in section 3, ?power characteristics,? updated ccb max to 533mhz for 1200mhz core device in ta b l e 4 , ?MPC8572E power dissipation.? ?in section 4.4, ?ddr clock timing,? changed ddrclk max to 100mhz. this change was announced in product bulletin #13572. ? clarified restrictions in section 4.5, ?platform to etsec fifo restrictions.? ?in tab le 8 , ?reset initialization timing specifications,? added note 2. ? added section 14, ?gpio.? ?in section 18.1, ?package parameters for the MPC8572E fc-pbga,? updated material composition to 63% sn, 37% pb. ?in section 18.2, ?mechanical dimensions of the MPC8572E fc-pbga , updated figure 61 to correct the package thickness and top view. ?in section 19.1, ?clock ranges,? updated ccb max to 533mhz for 1200mhz core device in ta b l e 7 6 , ?MPC8572E processor core clocking specifications.? ?in section 19.5.2, ?minimum platform frequency requirements for high-speed interfaces , ? changed minimum ccb clock frequency for proper pci express operation. ? added lpbse to description of lgpl4/lgta /lupwait/lpbse/lfrb signal in ta b l e 7 5 , ?MPC8572E pinout listing.? ? corrected supply voltage for gpio pins in ta b l e 7 5 , ?MPC8572E pinout listing.? ? applied note to sd1_pll_tpa in tab le 7 5 , ?MPC8572E pinout listing.? ? updated note regarding mdic in ta b l e 7 5 , ?MPC8572E pinout listing.? ? added note for lad pins in ta ble 7 5 , ?MPC8572E pinout listing.? ? updated ta b l e 8 6 , ?,part numbering nomenclature - rev 1.1.1? with rev 2.0 and rev 2.1 part number information. added note indicating that silicon version 2.0 is available for prototype purposes only and will not be available as a qualified device.
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 138 freescale semiconductor document revision history 1 08/2008 ? in section 22.1, ?part numbers fully addressed by this document,? added svr information in, ta b l e 8 6 ?part numbering nomenclature - rev 1.1.1,? for devices without security engine feature. 0 07/2008 ? initial release. table 88. document revision history (continued) rev. number date substantive change(s)
MPC8572E powerquicc iii integrated processor hardware specifications, rev. 4 freescale semiconductor 139 document revision history this page intentionally left blank
document number: MPC8572Eec rev. 4 06/2010 information in this document is provided solely to enable system and software implementers to use freescale semiconductor products. there are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. freescale semiconductor reserves the right to make changes without further notice to any products herein. freescale semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does freescale semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. ?typical? parameters which may be provided in freescale semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. freescale semiconductor does not convey any license under its patent rights nor the rights of others. freescale semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the freescale semiconductor product could create a situation where personal injury or death may occur. should buyer purchase or use freescale semiconductor products for any such unintended or unauthorized application, buyer shall indemnify and hold freescale semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that freescale semiconductor was negligent regarding the design or manufacture of the part. how to reach us: home page: www.freescale.com web support: http://www.freescale.com/support usa/europe or locations not listed: freescale semiconductor, inc. technical information center, el516 2100 east elliot road tempe, arizona 85284 1-800-521-6274 or +1-480-768-2130 www.freescale.com/support europe, middle east, and africa: freescale halbleiter deutschland gmbh technical information center schatzbogen 7 81829 muenchen, germany +44 1296 380 456 (english) +46 8 52200080 (english) +49 89 92103 559 (german) +33 1 69 35 48 48 (french) www.freescale.com/support japan: freescale semiconductor japan ltd. headquarters arco tower 15f 1-8-1, shimo-meguro, meguro-ku tokyo 153-0064 japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com asia/pacific: freescale semiconductor china ltd. exchange building 23f no. 118 jianguo road chaoyang district beijing 100022 china +86 10 5879 8000 support.asia@freescale.com for literature requests only: freescale semiconductor literature distribution center 1-800 441-2447 or +1-303-675-2140 fax: +1-303-675-2150 ldcforfreescalesemiconductor @hibbertgroup.com freescale, the freescale logo, codewarrior, coldfire, powerquicc, starcore, and symphony are trademarks of freescale semiconductor, inc. reg. u.s. pat. & tm. off. corenet, qoriq, quicc engine, and vortiqa are trademarks of freescale semiconductor, inc. all other product or service names are the property of their respective owners. the power architecture and power.org word marks and the power and power.org logos and related marks are trademarks and service marks licensed by power.org. rapidio is a registered trademark of the rapidio trade association. ieee 802.1, 802.3, 1149.1, and 1588 are registered trademarks of the institute of electrical and electronics engineers, inc. (ieee). this product is not endorsed or approved by the ieee. ? 2010 freescale semiconductor, inc.

▲Up To Search▲

Price & Availability of MPC8572E

	To Download MPC8572E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .