View M201UN02V1_2982363.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 1/26 au optronics corporation product specifications 20.1? uxga color tft-lcd module model name: m201un02 v.1 approved by prepared by idbu marketing division / au optronics croporation customer checked & approved by spec. no.: ddpm-un02-0.1 version: 1 to ta l p a g e s : 2 6 date: 2002-nov-09 www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 2/26 product specifications 20.1? uxga color tft-lcd module model name: m201un02 v.1 ( ? ) preliminary specifications ( ) final specifications note: this specification is subject to change without notice. www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 3/26 i contents ii record of revision 1.0 handling precautions 2.0 general description 2.1 display characteristics 2.2 functional block diagram 2.3 optical characteristics 2.4 pixel format image 3.0 electrical characteristics 3.1 absolute maximum ratings 3.2 connectors 3.3 signal pin 3.4 signal description 3.5 signal electrical characteristics 3.6 interface timing 3.6.1 timing characteristics 3.6.2 timing definition 3.7 power consumption 3.8 power on/off sequence 4.0 backlight characteristics 4.1 signal for lamp connector 4.2 parameter guide line for ccfl inverter 5.0 vibration, shock and drop 5.1 vibration and shock 5.2 drop test 6.0 environment 6.1 temperature and humidity 6.1.1 operating conditions 6.1.2 shipping conditions 6.2 atmospheric pressure 6.3 thermal shock 7.0 reliability 7.1 failure criteria 7.2 failure rate 7.2.1 usage 7.2.2 components de-rating 7.3 ccfl life 7.4 on/off cycle 8.0 safety 8.1 sharp edge requirement 8.2 material 8.2.1 toxicity 8.2.2 flammability 8.3 capacitors 8.4 hazardous voltage 9.0 other requirements 9.1 smoke free design 9.2 national test lab requirement 10.0 mechanical characteristics www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 4/26 ii record of revision version and date page old description new description remark 0.1 2002/10/11 all first edition for customer all 1.0 handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft-lcd module. 10) after installation of the tft-lcd module into an enclosure (lcd monitor housing, for example), do not twist nor bend the tft -lcd module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft -lcd module from outside. otherwise the tft -lcd module may be damaged. www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 5/26 2.0 general description this specification applies to the 20.1 inch color tft-lcd module m201un02. the display supports the uxga (1600(h) x 1200(v)) screen format and 16.7m colors (rgb 8-bits data). all input signals are 2 channel lvds interface compatible. this module does not contain an inverter card for backlight. 2.1 display characteristics the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 510(20.1") active area [mm] 408.0 (h) x 306.0 (v) pixels h x v 1600(x3) x 1200 pixel pitch [mm] 0.255 (per one triad) x 0.255 pixel arrangement r.g.b. vertical stripe display mode normally black white luminance [cd/m 2 ] 250 cd/m 2 (typ) contrast ratio 500 : 1 (typ) optical response time [msec] 25 (typ) nominal input voltage vdd [volt] +5.0 v power consumption (vdd line + ccfl line) [watt] 40w(typ.) (w/o inverter, all white pattern) weight [grams] 3700 (typ) physical size [mm] 432(w) x 331.4(h) x 23.1(d) electrical interface even/odd r/g/b data, 3 sync signal, clock support color 16.7m colors (rgb 8-bit data ) temperature range operating storage (shipping) [ o c] [ o c] 0 to +50 -20 to +60 www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 6/26 2.2 functional block diagram the following diagram shows the functional block of the 20.1 inches color tft-lcd module: lvds + 5v jae fi-x30s-hf jst bhsr-02vs-1x6 mating type: jae fi-x30s-h mating type: sm02b-bhss-1-tb connector dc/dc converter lvds receiver timing controller gamma correction tft-lcd 1600*(3)*1200 pixels x - driver ic y - driver ic g1 g1200 d1 d4800 inverter dc power 6 ccfl i/f + x-pcb au asic www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 7/26 2.3 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature): item unit conditions min. typ. max. [degree] [degree] horizontal (right) cr = 10 (left) tbd 85 85 - - viewing angle [degree] [degree] vertical (up) cr = 10 (down) tbd 85 85 - - contrast ratio normal direction tbd 500 [msec] raising time - tbd [msec] falling time - tbd response time (note 1) [msec] raising + falling - 25 tbd red x red y green x green y blue x color / chromaticity coordinates (cie) blue y white x 0.313 color coordinates (cie) white white y 0.329 white luminance at ccfl 6.0ma (central point) [cd/m 2 ] 200 250 - luminance uniformity (note 2) [%] 75 80 - crosstalk (in 60hz) (note 4) [%] 1.5 note 1: definition of response time: the output signals of photodetector are measured when the input signals are changed from ? black? to ? white? (falling time), and from ?white? to ? black? (rising time), respectively. the response time is interval between the 10% and 90% of amplitudes. refer to figure as below. tr r tr d 100 90 10 0 % op t i c a l response w hi t e bl ack w hi t e www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 8/26 note 2: brightness uniformity of these 9 points is defined as below: minimum luminance in 9 points (1-9) uniformity = ??????????????????? maximum luminance in 9 points (1-9) note 3: tco ?99 certification requirements and test me thods for environmental labeling of display report no. 2 defines luminance uniformity as below: ((lmax,+30deg. / lmin,+30deg.) + (lmax,-30deg. / lmin,-30deg.)) / 2 this panel is compatible with tco99 approbation in luminance uniformity <1.7, luminance contrast >0.5 note 4: 50 % 90 % 90 % 50 % 10 % 10 % 1/2 1/2 1/6 1/6 a b 1/2 1/2 1/6 1/6 2/3 1/3 1/3 2/3 a ? b? 184 gray level 184 gray level 0 gray level www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 9/26 unit: percentage of dimension of display area l l a -l a ? l / l a x 100%= 1.5% max., l a and l b are brightness at location a and b l l b -l b? l / l b x 100%= 1.5% max., l a? and l b? are brightness at location a? and b? note 4: pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1599 1600 1st line 1200 th line www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 10/26 3.0 electrical characteristics 3.1 absolute maximum ratings absolute maximum ratings of the module is as following: item symbol min max unit conditions logic/lcd drive voltage vin -0.3 +5.5 [volt] select lvds data order sellvds nc nc [volt] ccfl inrush current icfll - tbd [ma] note 1 ccfl current icfl - 7.5 [ma] rms operating temperature top 0 +50 [ o c] note 2 operating humidity hop 8 95 [%rh] note 2 storage temperature tst -20 +60 [ o c] note 2 storage humidity hst 8 95 [%rh] note 2 note 1 : duration=50 msec. note 2 : maximum wet-bulb should be 39 and no condensation. t=65 ,h=29% relative humidity % temperature -20 0 60 5 0 95 5 100 0 operation range storage range storage range 80 60 40 20 twb=39 t=40 ,h=95% t=60 ,h=39% t=50 ,h=55% www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 11/26 3.2 connectors physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation interface connector / interface card manufacturer jae or compatible type part number fi-x30s-hf mating housing part number fi-x30s-h connector name / designation lamp connector / backlight lamp manufacturer jst type part number bhsr-02vs-1 mating type part number sm02b-bhss-1-tb 3.3 signal pin pin# signal name pin# signal name 1 rxo0- 2 rxo0+ 3 rxo1- 4 rxo1+ 5 rxo2- 6 rxo2+ 7 gnd 8 rxoc- 9 rxoc+ 10 rxo3- 11 rxo3+ 12 rxe0- 13 rxe0+ 14 gnd 15 rxe1- 16 rxe1+ 17 gnd 18 rxe2- 19 rxe2+ 20 rxec- 21 rxec+ 22 rxe3- 23 rxe3+ 24 gnd 25 nc 26 nc 27 nc 28 power 29 power 30 power www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 12/26 3.4 signal description the module using a pair of lvds receiver sn75lvds82(texas instruments) or compatible. lvds is a differential signal technology for lcd interface and high speed data transfer device. transmitter shall be sn75lvds83(negative edge sampling) or compatible . the first lvds port(rxoxxx) transmits odd pixels while the second lvds port(rxexxx) transmits even pixels. pin # signal name description 1 rxo0- negative lvds differential data input (odd data) 2 rxo0+ positive lvds differential data input (odd data) 3 rxo1- negative lvds differential data input (odd data) 4 rxo1+ positive lvds differentia l data input (odd data) 5 rxo2- negative lvds differential data input (odd data, h-sync,v-sync,dsptmg) 6 rxo2+ positive lvds differential data input (odd data, h-sync,v-sync,dsptmg) 7 gnd power ground 8 rxoc- negative lvds differential clock input (odd clock) 9 rxoc+ positive lvds differential clock input (odd clock) 10 rxo3- negative lvds differential data input (odd data) 11 rxo3+ positive lvds differential data input (odd data) 12 rxe0- negative lvds differential data input (even clock) 13 rxe0+ positive lvds differential data input (even data) 14 gnd power ground 15 rxe1- positive lvds differential data input (even data) 16 rxe1+ negative lvds differential data input (even data) 17 gnd power ground 18 rxe2- negative lvds differential data input (even data) 19 rxe2+ positive lvds differential data input (even data) 20 rxec- negative lvds differential clock input (even clock) 21 rxec+ positive lvds differential clock input (even clock) 22 rxe3- negative lvds differential data input (even data) 23 rxe3+ positive lvds differential data input (even data) 24 gnd power ground 25 nc - 26 nc - 27 nc - 28 power power 29 power power 30 power power note: input signals of odd and even clock shall be the same timing. lvds data name description dsp display timing: when the signal is high, the pixel data shall be valid to be displayed v-s vertical sync: both positive and negative polarity are acceptable h-s horizontal sync: both positive and negative polarity are acceptable www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 13/26 ti lvds x?mitter sn75lvds83 module lvds signal (interface connector pin7) signal name low(open) d0 red0 d1 red1 d2 red2 d3 red3 d4 red4 d5 red7 d6 red5 d7 green0 d8 green1 d9 green2 d10 green6 d11 green7 d12 green3 d13 green4 d14 green5 d15 blue0 d16 blue6 d17 blue7 d18 blue1 d19 blue2 d20 blue3 d21 blue4 d22 blue5 d23 na d24 h sync d25 v sync d26 display timing d27 red6 www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 14/26 g0(0) r5(r3) r4(r2) r3(r1) r2(r0) r1(0) r0(0) rsv b7(b5) b6(b4) g7(g5) g6(g4) r7(r5) r6(r4) de vs hs b5(b3) b4(b2) b3(b1) b2(b0) b1(0) b0(0) g5(g3) g4(g2) g3(g1) g2(g0) g1(0) rclkp1 rap1 rbp1 rcp1 rdp1 g0(0) r5(r3) r4(r2) r3(r1) r2(r0) r1(0) r0(0) rsv b7(b5) b6(b4) g7(g5) g6(g4) r7(r5) r6(r4) b5(b3) b4(b2) b3(b1) b2(b0) b1(0) b0(0) g5(g3) g4(g2) g3(g1) g2(g0) g1(0) rclkp2 rap2 rbp2 rcp2 rdp2 note: r/g/b data 7:msb, r/g/b data 0:lsb o = ?first pixel data? e = ?second pixel data? www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 15/26 3.5 signal electrical characteristics input signals shall be low or hi-z state when vin is off it is recommended to refer the specifications of sn75lvds82dgg (texas instruments) in detail. each signal characteristics are as follows; parameter condition min max unit vth differential inputhigh voltage(vcm=+1.2v) 100 [mv] vtl differential input low voltage(vcm=+1.2v) -100 [mv] 3.6 interface timings basically, interface timings described here is not actual input timing of lcd module but output timing of sn75lvds82dgg (texas instruments) or equivalent. 3.6.1 timing characteristics signal item symbol min typ max unit dtclk freq. fdck tbd 81 82 mhz dtclk cycle tck 12.3 12.2 ns +v-sync frame rate 1/tv tbd 60 tbd hz +v-sync cycle tv 16.667 ms +v-sync cycle tv 1207 1250 lines +v-sync active level tva 2 3 lines +v-sync v-back porch tvb 4 46 lines +v-sync v-front porch tvf 1 1 lines +dsptmg v-line m 1200 lines +h-sync scan rate 1/th 75 khz +h-sync cycle th 830 1080 tck +h-sync active level tha(*1) 10 96 tck +h-sync back porch thb(*1) 15 152 tck +h-sync front porch thf 5 32 tck +dsptmg display pixels n 800 tck note: typical value refer to vesa standard, (*1) tha+thb should be less than 1024 tck. www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 16/26 3.6.2 timing definition 1688dot 112dot 248do t 48dot 1280dot h-sync dsptmg 42h 1h 38h 3h 1024h v-sync dsptmg note :1600x1200 at 60 hz (vesa standard) 3.7 power consumption input power specifications are as follows; symbol parameter min typ max units condition vdd logic/lcd drive voltage 4.5 5 5.5 [volt] idd vdd current tbd tbd [ma] iidd inrush vdd current tbd [a] t < 80us pdd vdd power tbd [watt] vin=5v, all white pattern vddrp allowable logic/lcd drive ripple voltage 100 [mv] p-p vddns allowable logic/lcd drive ripple noise 100 [mv] p-p www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 17/26 www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 18/26 3.8 power on/off sequence vin power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vin is off. 10 10 10 10 10 10 10 90 90 0 0 0 170m min 1 sec. 30 max , 1ms vin lamp on signal www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 19/26 4.0 backlight characteristics 4.1 signal for lamp connector pin # signal name 1 lamp high voltage 2 ground (black) 3 lamp high voltage 4 ground (white) 5 lamp high voltage 6 ground (white) 4.2 parameter guide line for cfl inverter symbol parameter min typ max units condition (l255) white luminance 200 250 - [cd/m 2 ] (ta=25 o c) iscfl ccfl standard current 5.5 6.0 6.5 [ma] rms (ta=25 o c) ircfl ccfl operation range 4.0 6.0 7.5 [ma] rms (ta=25 o c) fcfl ccfl frequency 35 50 80 [khz] (ta=25 o c) note 1 vicfl (0 o c) ccfl ignition voltage 1700 [volt] rms (ta=0 o c) note 2 vicfl (25 o c) ccfl ignition voltage 1200 [volt] rms (ta=25 o c) note 2 vcfl ccfl discharge voltage (reference) @ 6m a 750 825 [volt] rms (ta=25 o c) note 3 pcfl ccfl power consumption @6ma 27w 29.7 [watt] (ta=25 o c) note 3 note 1: ccfl frequency should be carefully determined to avoid interference between inverter and tft lcd note 2: ccfl inverter should be able to give out a power that has a generating capacity of over 1700 voltage. lamp units need 1700 voltage minimum for ignition www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 20/26 note 3: calculator value for reference (icflvcfl=pcfl) www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 21/26 5.0 vibration, shock, and drop 5.1 vibration & shock frequency: 10 - 200hz sweep: 30 minutes each axis (x, y, z) acceleration: 1.5g(10~200hz p- p) test method: acceleration (g) 1.5 frequency (hz) 10~200~10 active time(min) 30 5.2 shock test spec: acceleration (g) ?a 50 active time -b 20 wave form half-sin times 1 direction: x , y, z 5.3 drop test package test: the drop height is 60 cm. 6.0 environment the display module will meet the provision of this sp ecification during operating condition or after storage or shipment condition spec ified below. operation at 10% beyond th e specified range will not cause physical damage to the unit. 6.1 temperature and humidity 6.1.1 operating conditions the display module operates error free, when operated under the following conditions; temperature 0 0 c to 50 0 c relative humidity 8% to 95% wet bulb temperature 39.0 0 c www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 22/26 6.1.2 shipping conditions the display module operates error free, after the following conditions; temperature -20 0 c to 60 0 c relative humidity 8% to 95% wet bulb temperature 39.0 0 c 6.2 atmospheric pressure the display assembly is capable of being operated without affecting its operations over the pressure range as following specified; pressure note maximum pressure 1040hpa 0m = sea level minimum pressure 674hpa 3048m = 10.000 feet note : non-operation attitude limit of this display module = 30,000 feet. = 9145 m. 6.3 thermal shock the display module will not sustain damage after be ing subjected to 100 cycles of rapid temperature change. a cycle of rapid temperature change consists of varying the temperature from -20 0 c to 60 0 c, and back again. thermal shock cycle -20 0 c for 30min 60 0 c for 30min power is not applied during the test. after temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on. 7.0 reliability this display module and th e packaging of that will co mply following standards. 7.1 failure criteria the display assembly will be considered as failing unit when it no longer meets any of the requirements stated in this specification. only as for maximum white luminance, following criteria is applicable. note : maximum white luminance shall be 125 cd/m 2 or more. 7.2 failure rate www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 23/26 the average failure rate of the display module (from first power-on cycle till 1, 000 hours later) will not exceed 1.0%. the average failure rate of the disp lay module from 1,000 hours until 16,000 hours will not exceed 0.7% per 1000 hours. 7.2.1 usage the assumed usage for the above criteria is: 220 power-on hours per month 500 power on/off cycles per month maximum brightness setting operation to be within office environment (25 0 c typical) 7.2.2 component de-rating all the components used in this devi ce will be checked the load condition to meet the failure rate criteria. 7.3 ccfl life the assumed ccfl life will be longer th an 50,000 hours, typical value is 60 ,000 hours under st able condition at 25 5 o c; standard current at 6.0 0.5ma. definition of life: brightness becomes 50% or less than the minimum luminance value of ccfl. 7.4 on/off cycle the display module will be capable of being operated over the fo llowing on/off cycles. on/off value cycles +vin and ccfl power 30,000 10 seconds on / 10 seconds off 8.0 safety 8.1 sharp edge requirements there will be no sharp edges or comers on the display assembly that could cause injury. 8.2 materials 8.2.1 toxicity there will be no carcinogenic materi als used anywhere in the display mo dule. if toxic materials are used, they will be reviewed an d approved by the respon sible adt toxicologist. 8.2.2 flammability all components including electrical components that do not meet the flammability grade ul94- www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 24/26 v1 in the module will complete the flammability rating exception approval process. the printed circuit board will be made from material rated 94 -v1 or better. the actual ul flammability rating will be printed on the printed circuit board. 8.3 capacitors if any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 8.4 hazardous voltages any point exceeding 42.4 volts meets the requirement of the limited current circuit. the current through a 2k resistance is less than 0.7 x f (khz) ma. 9.0 other requirements 9.1 national test lab requirement the display module will satisfy a ll requirements for compliance to ul 1950, first edition u.s.a. information technology equipment csa c22.2 no.950-m89 canada, information technology equipment eec 950 international, information technology equipment en 60 950 international, information processing equipment (european norm for iec950) 9.2 label 9.2.1 product label to be defined 10.0 mechanical characteristics www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 25/26 www..net
(c) copyright au optronics, inc. february, 2002 all rights reserved. m201un02-1 ver0.1 no reproduction and redistribution allowed. 26/26 www..net

▲Up To Search▲

Price & Availability of M201UN02V1

	To Download M201UN02V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .