apex microtechnology corporation ? telephone (520) 690-8600 ? fax (520) 888-3329 ? orders (520) 690-8601 ? email prodlit@apexmicrotech.com 1 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ???????????????????????????????????? ???? introduction the EK51 evaluation kit provides a fast and easy breadboard solution for all devices in apexs psop1 package (24 pin psop). the EK51 includes the eval43 board shown in figure 1, as well as the universal eval36 board. the combination of the two boards provides a large area for breadboard circuit space while also providing an effective method of thermal management of the surface mount package. the device under evaluation is surface mounted directly to the eval43 pc board which provides a foil footprint area the size of the heat slug. this foil heat slug connection area consists of plated through thermal vias. the thermal vias offer a cost-effective way to decrease the thermal resistance between one side of the pc board which allows for the direct mounting of a heat sink or heat sink surface mount fan on the back side of the pc board. parts list part# description qty eval36 universal pc board, apex 1 eval43 pc board, psop1, apex 1 tsm-116-01-t-sv terminal strip, 16pin, samtec 2 ssw-116-01-t-s socket strip, 16pin, samtec 2 ox7r105kwn cap, 200v, 1f, ceramic 4 *erj-6geyor00v res, 0.0?, 0805smd, panasonic 4 *avs336m2ag24t cap, 100v, 33f, cde 4 *031606 heat sink w/ fan, 3.4c/w, aavid 1 or or *031613 heat sink, 11.0c/w, aavid 1 * parts not supplied. parts are application dependent. sug - gested part numbers are provided. figure 1: eval 43 assembly the psop1 should be assembled to the eval43 pc board using surface mount processes. solder paste may be dispensed or screen-printed on the dut pads as well as the foil heat slug pad. the heat slug on the bottom surface of the psop1 pro - vides maximum heat dissipation capabilities when soldered to the pcb foil footprint area. however, for prototype purposes, the tab can be thermally connected to the pcb foil area using thermal grease. if soldering the heat slug, ideally the psop1 should be soldered to the pcb using a solder re?ow furnace. if a re?ow furnace is not available, a heat plate capable of solder re?ow temperatures may be used. otherwise, the leads may be carefully soldered individually to the pcb with a thin tip soldering iron. however, in this case, the use of thermal grease under the heat tab is recommended instead of solder for thermal connection through the thermal vias. the kit comes with ceramic bypass capacitors, which should be soldered on the space provided on the eval43 board. also, space is provided for the appropriate electrolytic by-pass capacitors. although these capacitors are not provided in the kit, a recommended capacitor is listed for 100v applications. for higher voltage applications, a larger electrolytic capacitor can be mounted on the eval36 board. the eval43 is a generic evaluation board for the psop1. jumpers are required to make appropriate connection to +vs, -vs and ground. when applicable, surface mount 0805 0? resistors can be used in the locations provided. once all the surface mount components are installed, the heat sink can then be mounted to the back of the pc board. high thermal conductive grease should be used when mounting the heat sink to the pc board. note: a heat sink is not supplied with the kit, but several options are listed which are produced by aavid thermal product, inc. review figure 2 on the next page for all other assemblies needed to construct this evaluation kit. before you get started * all apex ampli?ers should be handled using proper esd precautions. * always provide the appropriate heat sinking. * always use adequate power supply bypass capacitors. * do not change connections while the circuit is powered. * initially set all power supplies to the minimum operating levels allowed in the device data sheet. * check for oscillations.
apex microtechnology corporation ? 5980 north shannon road ? tucson, arizona 85741 ? usa ? applications hotline: 1 (800) 546-2739 2 evaluation kit for psop1 EK51 figure 2: eval36 this data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. all speci?cations are subject to change without notice. EK51u rev a june 2002 ? 2002 apex microtechnology corp.
|
