View AN103_687102.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AN103 siliconix 10-mar-97 1 the fet constant-current source/limiter introduction the combination of low associated operating voltage and high output impedance makes the fet attractive as a constant-current source. an adjustable-current source (fig- ure 1) may be built with a fet, a variable resistor, and a small battery. for optimum thermal stability, the fet should be biased near the zero temperature coefficient point. d s + figure 1. field-effect transistor current source r s r l no tag whenever the fet is operated in the current saturated re- gion, its output conductance is very low. this occurs whenever the drain-source voltage v ds is at least 50% greater than the cut-off voltage v gs(off) . the fet may be biased to operate as a constant-current source at any cur- rent below its saturation current i dss . basic source biasing for a given device where i dss and v gs(off) are known, the approximate v gs required for a given i d is (1) v gs v gs(off) 1 i d i dss 1 k where k can vary from 1.8 to 2.0, depending on device ge- ometry. if k = 2.0, the series resistor r s required between source and gate is (2) r s v gs i d or r s v gs(off) i d 1 i d i dss a change in supply voltage or a change in load imped- ance, will change i d by only a small factor because of the low output conductance g oss . i d = ( v ds )(g oss ) (3) the value of g oss is an important consideration in the ac- curacy of a constant-current source where the supply volt- age may vary. as g oss may range from less than 1 s to more than 50 s according to the fet type, the dynamic impedance can be greater than 1 m to less than 20 k . this corresponds to a current stability range of 1 a to 50 a per volt. the value of g oss also depends on the op- erating point. output conductance g oss decrease approxi- mately linearly with i d . the relationship is (4) i d i dss g oss g oss where g oss = g oss (5) when v gs = 0 (6) so as v gs v gs(off) , g oss zero. for best regulation, i d must be considerably less than i dss . cascading for low g oss it is possible to achieve much lower g oss per unit i d by cascading two fets, as shown in figure 2. d s + sd figure 2. cascade fet current source v dd r s r l q 2 q 1 updates to this app note may be obtained via facsimile by calling siliconix faxback, 1-408-970-5600. please request faxback do cument #70596.
AN103 2 siliconix 10-mar-97 d s d s + + + (a) (b) figure 3. cascade fet v gs1 = 0 q 2 q 1 v gs2 g fs2 g oss2 i 2 v ds2 g oss1 v ds1 = v gs2 = i o /g oss1 i o v o now, i d is regulated by q 1 and v ds1 = v gs2 . the dc val- ue of i d is controlled by r s and q 1 . however, q 1 and q 2 both affect current stability. the circuit output conduc- tance is derived as follows: if g oss1 = g oss2 (7) (8) g o g oss 2 g fs g oss when rs 0 as in figure 2 (9) g o g oss 2 g fs 1 r s g fs in either case (r s = 0 or r s 0), the circuit output conductance is considerably lower than the g oss of a single fet. in designing any cascaded fet current source, both fets must be operated with adequate drain-gate voltage, v dg . that is, v dg v gs(off) , preferably v dg 2v gs(off) (10) if v dg < 2 v gs(off) , the g oss will be significantly increased, and circuit g o will deteriorate. for example: a jfet may have a typical g oss = 4 s at v ds = 20 v and v gs = 0. at v ds v gs(off) = 2 v, g oss 100 s. the best fets for current sources are those having long gates and consequently very low g oss . the siliconix 2n4340, j202, and sst202 exhibit typical g oss = 2 s at v ds = 20 v. these devices in the circuit of figure 4 will provide a current source adjustable from 5 a to 0.8 ma with internal impedance greater than 2 m at 0.2 ma. other siliconix part types such as the 2n4392, j112, and sst112 can provide 10 ma or higher current. q 1 d s + 30 v figure 4. adjustable current source r s = 1 m r s = 1 m r s 200 (optional) instead of the adjustable resistor, the jfets can be put in i dss range groupings with an appropriate r s resistor selected for each group. this method is common in high volume applications. the cascade circuit of figure 5 provides a current adjustable from 2 a to 0.8 ma with internal resistance greater than 10 m d s + 30 v d s q 2 q 1 100 (optional) r s q 1 = 2n4340, j202, sst202 q 2 = 2n4341, j304, sst304 r s = 1 m figure 5. cascade fet current source
AN103 siliconix 10-mar-97 3 cr470 cr430 cr390 cr360 cr330 cr300 cr270 cr240 cr220 cr200 cr180 cr160 sst/j504 sst/j503 sst/j502 j501 j500 part type 0.1 0.2 0.5 1 2 5 10 i f regulator current (ma) figure 6. standard series current regulator range to-18 2-lead package j = to-226aa 2-lead package sst = to-236 (sot-23) package i f v f sst/j510 sst/j509 sst/j508 sst/j507 sst/j506 sst/j505 sst/j511 standard two-leaded devices siliconix offers a special series of two-leaded jfets with a resistor fabricated on the device, thus creating a 10% current range. devices are available in ranges from 1.6 ma (cr160) to 4.7 ma (cr470). for designs requiring a 20% current range, siliconix offers devices rated from 0.24 ma typical (j500) through 4.7 ma typical (j511) in a two-leaded to-226a (to-92) package. the sst502 series is available in surface mount to-236 (sot-23). each of these two-leaded devices can be used to replace several typical components. figure 6 shows the current ranges of these two device series. further information is contained in the individual data sheets appearing elsewhere in this data book or from siliconix faxback. the cr160 series features guaranteed peak operating voltage minimum of 100 v with a typical of 180 v. the j500 series features 50 v minimum with a typical of 100 v. the lower current devices in both series provide excellent current regulation down to as little as 1 v. bias resistor selection all industry jfet part types exhibit a significant varia- tion in i dss and v gs(off) on min/max specifications and device-to-device variations. using the simple source biasing current source as illus- trated in figure 1, the designer can graphically calculate the r s which best fits the desired drain current i d. figure 7 plotting i d versus v gs over the military temperature range shows the resulting i d for different values of r s . the r s lines are constructed by drawing the slope of the r s desired value starting at the origin, eg. r s = 2 k slope. find a convenient point on the x y axis to mark a v gs i d of 2 k such as v gs = 1.5 v and i d = 0.75 ma. then, draw a straight line from this point to the origin. the intersection of this r s line and the device i d versus v gs will be the operating i d . in this example, the result- ing i d = 0.35 ma at t j = 25 c. the intercepts of the t j = 55 c and 125 c show the minimal variation with temperature. also note that jfets have a i d current where there is no change with temperature variation. to achieve this t c , the v gs voltage (i d x r s ) is approximately: v gs(0tc) v gs(off) 0.65 v (11)
AN103 4 siliconix 10-mar-97 figure 7. jfet typical transfer characteristic 2.00 0 1.2 1.6 2 0.8 0.4 0.25 0 v gs gate-source voltage (v) drain current (ma) i d v ds = 4 to 20 v 2n4339 max sst/j202 (low end) 0.50 0.75 1.00 1.25 1.50 1.75 t j = 55 c 125 c r s = 0.2 k 0.5 k 1 k 2 k 5 k 10 k 20 k 25 c figure 8. source biased drain-current vs. source resistance 1000 0.1 100 10 r s source resistance (k ) drain current ( i d a) v dd = 5 to 30 v t j = 25 c except as noted 10 1 100 t j = 55 c 125 c 2n/pn4119a sst4119 max 2n/pn4118a sst4118 max 2n/pn4119a sst4119 min 2n/pn4118a sst4118 min 2n/pn4117a sst4117 min 2n/pn4117a sst4117 max 0.5 50 5 figure 9. jfet source biased drain-current vs. source resistance 2 0.1 20 1 0.01 r s source resistance (k ) drain current (ma) i d 1 v dd = 4 to 20 v t j = 25 c except as noted r s 0.1 10 t j = 55 c 125 c sst/j202 max 2n4338 max sst/j202 min 2n4339 min sst/j201 max sst/j201 2n4338 min v dd 0.5 5 25 c 2n4339 max 25 c
AN103 siliconix 10-mar-97 5 choosing the correct jfet for source biasing each of the siliconix device data sheets include typical transfer curves that can be used as illustrated in figure 7. several popular devices are ideal for source biased cur- rent sources covering a few as to 20 ma. to aid the de- signer, the devices in table 1 have been plotted to show the drain current, i d , versus the source resistance, r s , in figures 8, 9, and 10. most plots include the likely worst case i d variations for a particular r s . for tighter current control, the jfet production lot can be divided into ranges with an appropriate resistor selection for each range. table 1: source biasing device recommendations practical current range i d (ma) through-hole plastic device surface mount device metal can device 0.01 0.02 pn4117a sst4117 2n4117a 0.01 0.04 pn4118a sst4118 2n4118a 0.02 0.1 pn4119a sst4119 2n4119a 0.01 0.1 j201 sst201 2n4338 0.02 0.3 j202 sst202 2n4339 0.1 2 j113 sst113 2n4393 0.2 10 j112 sst112 2n4392 55 c 20 0.1 10 0.1 r s source resistance (k ) drain current ( i d a) m 1 1 figure 10. jfet source biased drain-current vs. source resistance 10 r s v dd = 5 to 30 v t j = 25 c except as noted 125 c 2n4393, sst/j113 max mid 2n4392, sst/j112 min 2n4392, sst/j112 min 2n4393 sst/j113 mid v dd 5 0.5 t j = 25 c

▲Up To Search▲

Price & Availability of AN103

Part #	Manufacturer	Description	Price	BuyNow Qty.
FMWAN1031 98AK2540	Fairview Microwave Inc	Standard Gain Horn Waveguide Antenna, Wr-5, 140 Ghz To 220 Ghz, Ug-387/U-Mod Round Cover Flange, 20 Dbi Nominal Gain Rohs Compliant: Yes \|Fairview Microwave FMWAN1031	25: USD2596.38 10: USD2688.45 5: USD2743.69 3: USD2798.93 1: USD2909.42	2
FMWAN1032 98AK2541	Fairview Microwave Inc	Standard Gain Horn Waveguide Antenna, Wr-5, 140 Ghz To 220 Ghz, Ug-387/U-Mod Round Cover Flange, 25 Dbi Nominal Gain Rohs Compliant: Yes \|Fairview Microwave FMWAN1032	25: USD1376.76 10: USD1404.48 5: USD1459.92 3: USD1506.12 1: USD1580.04	1
FMWAN1037 98AK2546	Fairview Microwave Inc	Conical Gain Horn Waveguide Antenna, Wr-15, 58 Ghz To 68 Ghz, Ug-385/U Round Cover Flange, 10 Dbi Nominal Gain Rohs Compliant: Yes \|Fairview Microwave FMWAN1037	25: USD781.81 10: USD797.55 5: USD829.03 3: USD855.27 1: USD897.24	1
FMWAN1036 98AK2545	Fairview Microwave Inc	Conical Gain Horn Waveguide Antenna, Wr-19, 50 Ghz To 58 Ghz, Ug-383/U-Mod Round Cover Flange, 25 Dbi Nominal Gain Rohs Compliant: Yes \|Fairview Microwave FMWAN1036	25: USD1052.24 10: USD1073.43 5: USD1115.8 3: USD1151.11 1: USD1207.61	1
FMWAN1035 98AK2544	Fairview Microwave Inc	Conical Gain Horn Waveguide Antenna, Wr-19, 50 Ghz To 58 Ghz, Ug-383/U-Mod Round Cover Flange, 20 Dbi Nominal Gain Rohs Compliant: Yes \|Fairview Microwave FMWAN1035	25: USD889.98 10: USD907.9 5: USD943.74 3: USD973.6 1: USD1021.39	1

Part #	Manufacturer	Description	Price	BuyNow Qty.
PEWAN1030 3985-PEWAN1030-ND	Pasternack Enterprises	WR-5 Waveguide Standard Gain Hor	25: USD864.49 10: USD882.88 5: USD901.28 1: USD919.67	2
PEWAN1035 3985-PEWAN1035-ND	Pasternack Enterprises	WR-19 Waveguide Conical Gain Hor	25: USD574.45 10: USD586.68 5: USD598.9 1: USD611.12	2
PEWAN1036 3985-PEWAN1036-ND	Pasternack Enterprises	WR-19 Waveguide Conical Gain Hor	25: USD872.87 10: USD891.44 5: USD910.01 1: USD928.58	2
PEWAN1039 3985-PEWAN1039-ND	Pasternack Enterprises	WR-15 Waveguide Conical Gain Hor	25: USD738.58 10: USD754.29 5: USD770.01 1: USD785.72	1
AN1032 1441-1316-ND	Pentair Equipment Protection - Hoffman	CLIP NUT PKG (QTY 20)	100: USD96.5055 50: USD98.7326 25: USD100.2172 10: USD102.073 5: USD103.928 1: USD111.35	1

Part #	Manufacturer	Description	Price	BuyNow Qty.
E36D401CAN103MEM9U 661-6D401CAN103MEM9U	United Chemi-Con Inc	Aluminum Electrolytic Capacitors - Screw Terminal	1: USD70.77 9: USD64.63 27: USD62.59 54: USD60.55 108: USD57.89	0
E37L501CAN103MFM9U 661-7L501CAN103MFM9U	United Chemi-Con Inc	Aluminum Electrolytic Capacitors - Screw Terminal	1: USD112.46 10: USD108.75 25: USD107.53 50: USD106.29	0
E36D451CAN103MEM9Q 661-6D451CAN103MEM9Q	United Chemi-Con Inc	Aluminum Electrolytic Capacitors - Screw Terminal	9: USD86.14 27: USD84.63 54: USD83.13	0
E36D401CAN103MEM9M 661-E36D401CAN103MEM	United Chemi-Con Inc	Aluminum Electrolytic Capacitors - Screw Terminal 10000uF 400 Volt	18: USD58.98 27: USD56.94 54: USD54.91 108: USD52.27	0
E36F401CAN103MFE3U 661-6F401CAN103MFE3U	United Chemi-Con Inc	Aluminum Electrolytic Capacitors - Screw Terminal	20: USD72.35 60: USD71 100: USD69.26	0

Part #	Manufacturer	Description	Price	BuyNow Qty.
VC-806A-ECW-FAAN-103M000000 VC-806A-ECW-FAAN-103M000000	Microchip Technology Inc	VC-806A-ECW-FAAN-103M000000, Projected EOL: 2049-04-23	100: USD17.59 25: USD19.35 1: USD23.22	0
VC-806A-ECW-FAAN-103M000000TR VC-806A-ECW-FAAN-103M000000TR	Microchip Technology Inc	VC-806A-ECW-FAAN-103M000000TR, Projected EOL: 2049-09-01	5000: USD3.7 1: USD3.74	0

Part #	Manufacturer	Description	Price	BuyNow Qty.
FMWAN1031 74901479	Fairview Microwave Inc	Standard Gain Horn Waveguide Antenna, WR-5, 140 GHz to 220 GHz, UG-387/U-Mod Ro \| Fairview Microwave FMWAN1031	1: USD1184.2	0
FMWAN1032 74901478	Fairview Microwave Inc	Standard Gain Horn Waveguide Antenna, WR-5, 140 GHz to 220 GHz, UG-387/U-Mod Ro \| Fairview Microwave FMWAN1032	1: USD1223.67	0
FMWAN1037 74901473	Fairview Microwave Inc	Conical Gain Horn Waveguide Antenna, WR-15, 58 GHz to 68 GHz, UG-385/U Round Co \| Fairview Microwave FMWAN1037	1: USD696.18 3: USD647.44	0
FMWAN1036 74901474	Fairview Microwave Inc	Conical Gain Horn Waveguide Antenna, WR-19, 50 GHz to 58 GHz, UG-383/U-Mod Roun \| Fairview Microwave FMWAN1036	1: USD933.01	0
AC60A-N10-3Z-B 73182138	SMC Corporation of America	FR/L COMBO MODULAR, 1NPT, AC-B SERIES \| SMC Corporation AC60A-N10-3Z-B	1: USD220.15	0

Part #	Manufacturer	Description	Price	BuyNow Qty.
AN1032	Pentair Equipment Protection - Hoffman	Clip Nut Package for Rack Mounting Angel Quantity 20, #10-32, Plated, Steel	100: USD117.31 75: USD119.1 50: USD120.91 25: USD126.14 10: USD129.87 5: USD135.88 1: USD147.2	0

Part #	Manufacturer	Description	Price	BuyNow Qty.
CFCLEAN1.03.07 CFCLEAN1.03.07	igus Inc	Wire: control cable; chainflex® CFCLEAN1; 7x0.34mm2; white; 5mm	100: USD29.44 50: USD31.7 25: USD36.23 5: USD40.76	0
CFCLEAN1.03.02 CFCLEAN1.03.02	igus Inc	Wire: control cable; chainflex® CFCLEAN1; 2x0.34mm2; white; 3.5mm	100: USD16.82 50: USD18.12 25: USD20.71 5: USD23.3	0

Part #	Manufacturer	Description	Price	BuyNow Qty.
FAN103MY	Fairchild Semiconductor Corporation	PRIMARY-SIDE-REGULATION PWM CONTROLLER(PWM-PSR) Switching Controller, Current-mode, 53kHz Switching Freq-Max, PDSO8		1400

Part #	Manufacturer	Description	Price	BuyNow Qty.
LCAN1/0-38-X 000000000006077144	Panduit Corp	Terminals RING-LUG 1/0 3/8 CU SN		0

Part #	Manufacturer	Description	Price	BuyNow Qty.
PLA10AN1030R7R2B PLA10AN1030R7R2B	Murata Manufacturing Co Ltd	(Alt: PLA10AN1030R7R2B)		0

Part #	Manufacturer	Description	Price	BuyNow Qty.
PLA10AN1030R7R2B	Murata Manufacturing Co Ltd	IN STOCK SHIP TODAY	1000: USD1 100: USD1.15 1: USD1.54	2

Part #	Manufacturer	Description	Price	BuyNow Qty.
PEWAN1035 PEWAN1035	Pasternack Enterprises	Key Specifications, Waveguide Size: WR-19, Frequency, Min: 50 GHz, Frequency, Max: 58 GHz, Beam Width V: 20, Beam Width H: 16. WR-19 Waveguide Conical Gain Horn Antenna Operating from 50 GHz to 58 GHz with a Nominal 20 dBi Gain with UG-383/U-Mod Round Cover Flange. PEWAN1035 WR-19 conical gain horn antenna is also known as a waveguide horn. This WR-19 conical gain horn antenna has a 20 dBi nominal gain and a round cover flange. Our 20 dBi WR-19 horn antenna has a minimum frequency of 50 GHz and a maximum frequency of 58 GHz. WR19 conical gain horn waveguide antenna PEWAN1035 has a vertical beam width of 20 and horizontal of 16 degrees at 3 dB. This WR19 conical gain horn antenna with 20 dBi is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our WR-19 waveguide horn antenna can ship worldwide the same day as it is purchased as with our other available RF parts.	1: USD611.12 5: USD598.9 10: USD586.68	2
PEWAN1031 PEWAN1031	Pasternack Enterprises	Key Specifications, Waveguide Size: WR-5, Frequency, Min: 140 GHz, Frequency, Max: 220 GHz, Beam Width V: 13, Beam Width H: 13. WR-5 Waveguide Standard Gain Horn Antenna Operating from 140 GHz to 220 GHz with a Nominal 20 dBi Gain with UG-387/U-Mod Round Cover Flange. PEWAN1031 WR-5 standard gain horn antenna is also known as a waveguide horn. This WR-5 standard gain horn antenna has a 20 dBi nominal gain and a round cover flange. Our 20 dBi WR-5 horn antenna has a minimum frequency of 140 GHz and a maximum frequency of 220 GHz. WR5 standard gain horn waveguide antenna PEWAN1031 has a vertical beam width of 13 and horizontal of 13 degrees at 3 dB. This WR-5 standard gain horn antenna with 20 dBi is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our WR-5 waveguide horn antenna can ship worldwide the same day as it is purchased as with our other available RF parts.	1: USD916.67 5: USD898.34 10: USD880	2
PEWAN1039 PEWAN1039	Pasternack Enterprises	Key Specifications, Waveguide Size: WR-15, Frequency, Min: 58 GHz, Frequency, Max: 68 GHz, Beam Width V: 20, Beam Width H: 16. WR-15 Waveguide Conical Gain Horn Antenna Operating from 58 GHz to 68 GHz with a Nominal 20 dBi Gain with UG-385/U Round Cover Flange. PEWAN1039 WR-15 conical gain horn antenna is also known as a waveguide horn. This WR-15 conical gain horn antenna has a 20 dBi nominal gain and a round cover flange. Our 20 dBi WR 15 horn antenna has a minimum frequency of 58 GHz and a maximum frequency of 68 GHz. WR15 conical gain horn waveguide antenna PEWAN1039 has a vertical beam width of 20 and horizontal of 16 degrees at 3 dB. This WR15 conical gain horn antenna with 20 dBi is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our WR-15 waveguide horn antenna can ship worldwide the same day as it is purchased as with our other available RF parts.	1: USD785.72 5: USD770.01 10: USD754.29	1
PEWAN1038 PEWAN1038	Pasternack Enterprises	Key Specifications, Waveguide Size: WR-15, Frequency, Min: 58 GHz, Frequency, Max: 68 GHz, Beam Width V: 36, Beam Width H: 30. WR-15 Waveguide Conical Gain Horn Antenna Operating from 58 GHz to 68 GHz with a Nominal 15 dBi Gain with UG-385/U Round Cover Flange. PEWAN1038 WR-15 conical gain horn antenna is also known as a waveguide horn. This WR-15 conical gain horn antenna has a 15 dBi nominal gain and a round cover flange. Our 15 dBi WR-15 horn antenna has a minimum frequency of 58 GHz and a maximum frequency of 68 GHz. WR-15 conical gain horn waveguide antenna PEWAN1038 has a vertical beam width of 36 and horizontal of 30 degrees at 3 dB. This WR-15 conical gain horn antenna with 15 dBi is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our WR 15 waveguide horn antenna can ship worldwide the same day as it is purchased as with our other available RF parts.	1: USD1380 5: USD1352.4 10: USD1324.8	0
PEWAN1033 PEWAN1033	Pasternack Enterprises	Key Specifications, Waveguide Size: WR-19, Frequency, Min: 50 GHz, Frequency, Max: 58 GHz, Beam Width V: 58, Beam Width H: 53. WR-19 Waveguide Conical Gain Horn Antenna Operating from 50 GHz to 58 GHz with a Nominal 10 dBi Gain with UG-383/U-Mod Round Cover Flange. PEWAN1033 WR-19 conical gain horn antenna is also known as a waveguide horn. This WR-19 conical gain horn antenna has a 10 dBi nominal gain and a round cover flange. Our 10 dBi WR-19 horn antenna has a minimum frequency of 50 GHz and a maximum frequency of 58 GHz. WR-19 conical gain horn waveguide antenna PEWAN1033 has a vertical beam width of 58 and horizontal of 53 degrees at 3 dB. This WR-19 conical gain horn antenna with 10 dBi is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our WR-19 waveguide horn antenna can ship worldwide the same day as it is purchased as with our other available RF parts.	1: USD488.89 5: USD479.11 10: USD469.33	2

Part #	Manufacturer	Description	Price	BuyNow Qty.
PLA10AN1030R7R2B	MFG UPON REQUEST			15826
PLA10AN1030R7R2B	Murata Manufacturing Co Ltd			2117
AN1-0361-2	Antenova M2M			55
SWIAN1030	MFG UPON REQUEST			7
HT55AN103GN	MFG UPON REQUEST			954

Part #	Manufacturer	Description	Price	BuyNow Qty.
AN103	Panasonic Electronic Components	AN103		0
PLA10AN1030R7R2B	Murata Manufacturing Co Ltd	PLA10AN1030R7R2B		0

	To Download AN103 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .