 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SPEC NO : SPECIFICATION CUSTOMER PRODUCT MODEL NO PREPARED APPROVED SAW FILTER HDBF19900A22 CHECKED D A T E CUSTOMER RECEIVED: CHECKED APPROVED DATE Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 1 of 6 SAW FILTER HDBF19900A22 History Record Date Spec No Part No Customer No Modify Content Remark www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 2 of 6 SAW FILTER HDBF19900A22 1. SCOPE This specification shall cover the characteristics of SAW filter with the page system. HDBF19900A22 used for 2. ELECTRICAL SPECIFICATION Maximum incident power in passband Max.DC voltage between any 2 terminals Storage temperature range Operation temperature range Suitable for lead-free soldering-Max.soldering profile +15dBm 30VDC -40 to +85 -10 to +85 260 for 30s Electronic Characteristics Parameter Center Frequency Insertion Loss 1dB Bandwidth Amplitude Ripple over f0100KHz f0-800 to f0-600KHz and f0+600 to f0+800KHz f0-30MHz to f0-800KHz f0+800KHz to f0+17MHz f0-80MHz to f0-30MHz f0+17MHz to f0+80MHz Group Delay Variation overf0100KHz Frequency Temperature coefficient Minimum 100 20 28 28 35 35 Typical 199.0 0.032 Maximum 7 0.5 500 Unit MHz dB KHz dB dB dB dB dB dB nsec ppm/C www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 3 of 6 SAW FILTER HDBF19900A22 TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 4 of 6 SAW FILTER HDBF19900A22 4.DIMENSION Dimension A B C D E H P min 8.9 6.9 mm typ 9.1 7.1 0.9 0.8 0.76 2.54 max 9.3 7.3 1.5 0.72 0.80 Pin Configuration 2 Input 7 Output Other Ground www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 5 of 6 SAW FILTER HDBF19900A22 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40for 30 minutes. Following by a high temperature of +25 for 5 Minutes and a higher temperature of +85 for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in table 1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260 5 for 101 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in table 1. 5-3 Solderability Submerge the device terminals into the solder bath at 245 5 for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in table 1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:info@shoulder.cn Page 6 of 6 |
Price & Availability of HDBF19900A22
 |
|
|
|
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |