|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
NTLJS3113P Power MOSFET Features -20 V, -7.7 A, mCoolt Single P-Channel, 2x2 mm, WDFN Package * WDFN Package Provides Exposed Drain Pad for Excellent Thermal * * * * * Conduction 2x2 mm Footprint Same as SC-88 Package Lowest RDS(on) Solution in 2x2 mm Package 1.5 V RDS(on) Rating for Operation at Low Voltage Logic Level Gate Drive Low Profile (< 0.8 mm) for Easy Fit in Thin Environments This is a Pb-Free Device V(BR)DSS http://onsemi.com RDS(on) MAX 40 mW @ -4.5 V -20 V 50 mW @ -2.5 V 75 mW @ -1.8 V 200 mW @ -1.5 V S -7.7 A ID MAX (Note 1) Applications * DC-DC Converters (Buck and Boost Circuits) * Optimized for Battery and Load Management Applications in * Portable Equipment such as, Cell Phones, PDA's, Media Players, etc. High Side Load Switch G MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Parameter Drain-to-Source Voltage Gate-to-Source Voltage Continuous Drain Current (Note 1) Steady State t5s Power Dissipation (Note 1) Steady State t5s Continuous Drain Current (Note 2) Power Dissipation (Note 2) Pulsed Drain Current TA = 25C Steady State TA = 85C TA = 25C tp = 10 ms PD IDM TJ, TSTG IS TL ID TA = 25C TA = 85C TA = 25C PD TA = 25C 3.3 -3.5 -2.5 0.7 -23 -55 to 150 -2.8 260 W A C A C D G 2 3 D 1 A Symbol VDSS VGS ID Value -20 8.0 -5.8 -4.4 -7.7 1.9 W Unit V V A Pin 1 S D P-CHANNEL MOSFET D WDFN6 CASE 506AP MARKING DIAGRAM 1 2 J8MG G 3 6 5 4 J8 = Specific Device Code M = Date Code G = Pb-Free Package (Note: Microdot may be in either location) PIN CONNECTIONS 6 5 4 D D S Operating Junction and Storage Temperature Source Current (Body Diode) (Note 2) Lead Temperature for Soldering Purposes (1/8 from case for 10 s) D S (Top View) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Surface Mounted on FR4 Board using 1 in sq pad size (Cu area = 1.127 in sq [2 oz] including traces). 2. Surface Mounted on FR4 Board using the minimum recommended pad size, (30 mm2, 2 oz Cu). ORDERING INFORMATION Device NTLJS3113PT1G Package WDFN6 (Pb-Free) Shipping 3000/Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2006 1 May, 2006 - Rev. 3 Publication Order Number: NTLJS3113P/D NTLJS3113P THERMAL RESISTANCE RATINGS Parameter Junction-to-Ambient - Steady State (Note 3) Junction-to-Ambient - t 5 s (Note 3) Junction-to-Ambient - Steady State Min Pad (Note 4) Symbol RqJA RqJA RqJA Max 65 38 180 C/W Unit 3. Surface Mounted on FR4 Board using 1 in sq pad size (Cu area = 1.127 in sq [2 oz] including traces). 4. Surface Mounted on FR4 Board using the minimum recommended pad size (30 mm2, 2 oz Cu). MOSFET ELECTRICAL CHARACTERISTICS (TJ = 25C unless otherwise noted) Parameter OFF CHARACTERISTICS Drain-to-Source Breakdown Voltage Drain-to-Source Breakdown Voltage Temperature Coefficient Zero Gate Voltage Drain Current Gate-to-Source Leakage Current ON CHARACTERISTICS (Note 5) Gate Threshold Voltage Negative Gate Threshold Temperature Coefficient Drain-to-Source On-Resistance VGS(TH) VGS(TH)/TJ RDS(on) VGS = -4.5, ID = -3.0 A VGS = -2.5, ID = -3.0 A VGS = -1.8, ID = -2.0 A VGS = -1.5, ID = -1.8 A Forward Transconductance gFS VDS = -16 V, ID = -3.0 A CHARGES, CAPACITANCES AND GATE RESISTANCE Input Capacitance Output Capacitance Reverse Transfer Capacitance Total Gate Charge Threshold Gate Charge Gate-to-Source Charge Gate-to-Drain Charge Gate Resistance SWITCHING CHARACTERISTICS (Note 6) Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time td(ON) tr td(OFF) tf VGS = -4.5 V, VDD = -10 V, ID = -3.0 A, RG = 3.0 W 6.9 17.5 60 56.5 ns CISS COSS CRSS QG(TOT) QG(TH) QGS QGD RG VGS = -4.5 V, VDS = -16 V, ID = -3.0 A 1329 VGS = 0 V, f = 1.0 MHz, VDS = -16 V 213 120 13 1.5 2.2 2.9 14.4 W 15.7 nC pF VGS = VDS, ID = -250 mA -0.45 -0.67 2.68 32 44 67 90 5.9 40 50 75 200 S -1.0 V mV/C mW V(BR)DSS V(BR)DSS/TJ IDSS IGSS VGS = 0 V, ID = -250 mA ID = -250 mA, Ref to 25C TJ = 25C TJ = 85C -20 -10.1 -1.0 -10 1.0 mA V mV/C mA Symbol Test Conditions Min Typ Max Unit VDS = -16 V, VGS = 0 V VDS = 0 V, VGS = 8.0 V DRAIN-SOURCE DIODE CHARACTERISTICS Forward Recovery Voltage Reverse Recovery Time Charge Time Discharge Time Reverse Recovery Time VSD tRR ta tb QRR VGS = 0 V, dISD/dt = 100 A/ms, IS = -1.0 A VGS = 0 V, IS = -1.0 A TJ = 25C TJ = 125C -0.78 -0.67 70.8 14.3 56.4 44 nC 106 ns -1.2 V 5. Pulse Test: Pulse Width v 300 ms, Duty Cycle v 2%. 6. Switching characteristics are independent of operating junction temperatures. http://onsemi.com 2 NTLJS3113P TYPICAL PERFORMANCE CURVES (TJ = 25C unless otherwise noted) 7 -ID, DRAIN CURRENT (AMPS) 6 5 4 -1.4 V 3 2 1 0 0 1 2 3 4 5 6 -VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) -1.3 V -1.2 V -1.1 V -1.5 V VGS = -1.7 V to -8 V TJ = 25C -1.6 V -ID, DRAIN CURRENT (AMPS) 9 8 7 6 5 4 3 2 1 0 0 0.5 1 TJ = 125C TJ = -55C 1.5 2 2.5 3 TJ = 25C VDS 10 V -VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) Figure 1. On-Region Characteristics RDS(on), DRAIN-TO-SOURCE RESISTANCE (W) RDS(on), DRAIN-TO-SOURCE RESISTANCE (W) Figure 2. Transfer Characteristics 0.04 VGS = -4.5 V TJ = 100C 0.08 TJ = 25C 0.07 0.06 0.05 0.04 0.03 0.02 0.01 1 2 3 VGS = -4.5 V VGS = -2.5 V VGS = -1.8 V 0.03 TJ = 25C TJ = -55C 0.02 1.0 1.5 2.0 2.5 3.0 4 5 6 7 -ID, DRAIN CURRENT (AMPS) -ID, DRAIN CURRENT (AMPS) Figure 3. On-Resistance versus Drain Current Figure 4. On-Resistance versus Drain Current and Gate Voltage 100000 RDS(on), DRAIN-TO-SOURCE RESISTANCE (NORMALIZED) 1.5 ID = -6 A VGS = -4.5 V VGS = 0 V -IDSS, LEAKAGE (nA) 10000 1.3 TJ = 150C 1.1 1000 TJ = 100C 100 0.9 0.7 -50 -25 0 25 50 75 100 125 150 10 2 4 6 8 10 12 14 16 18 20 TJ, JUNCTION TEMPERATURE (C) -VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 5. On-Resistance Variation with Temperature Figure 6. Drain-to-Source Leakage Current versus Voltage http://onsemi.com 3 NTLJS3113P TYPICAL PERFORMANCE CURVES (TJ = 25C unless otherwise noted) VDS = VGS = 0 V Ciss TJ = 25C -VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) 2800 2400 C, CAPACITANCE (pF) 2000 1600 1200 800 400 0 5 VGS 0 VDS 5 10 15 20 Crss Coss 5 QT 4 20 -VDS , DRAIN-TO-SOURCE VOLTAGE (VOLTS) 16 3 VDS QGD VGS 12 2 QGS 8 1 0 0 ID = -3.0 A TJ = 25C 4 8 12 QG, TOTAL GATE CHARGE (nC) 4 0 GATE-TO-SOURCE OR DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 7. Capacitance Variation 1000 -Is, SOURCE CURRENT (AMPS) VDD = -15 V ID = -3.0 A VGS = -4.5 V t, TIME (ns) 100 Figure 8. Gate-To-Source and Drain-To-Source Voltage versus Total Charge 3 VGS = 0 V 2.5 2 1.5 1 TJ = 150C 0.5 TJ = 25C 0 0 0.2 0.4 0.8 0.6 1.0 -VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS) td(off) tf tr td(on) 10 1 1 10 RG, GATE RESISTANCE (OHMS) 100 Figure 9. Resistive Switching Time Variation versus Gate Resistance Figure 10. Diode Forward Voltage versus Current 100 -ID, DRAIN CURRENT (AMPS) See Note 2, Page 1 SINGLE PULSE TC = 25C 10 100 ms 1 ms 1 10 ms 0.1 RDS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT 0.1 dc 0.01 1 10 100 -VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 11. Maximum Rated Forward Biased Safe Operating Area http://onsemi.com 4 NTLJS3113P TYPICAL PERFORMANCE CURVES (TJ = 25C unless otherwise noted) EFFECTIVE TRANSIENT THERMAL RESISTANCE 1000 100 D = 0.5 0.2 0.1 10 0.05 0.02 0.01 1 SINGLE PULSE 0.1 0.000001 0.00001 0.0001 0.001 P(pk) See Note 2 on Page 1 D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TA = P(pk) RqJA(t) 10 100 1000 t1 t2 DUTY CYCLE, D = t1/t2 0.01 0.1 t, TIME (sec) 1 Figure 12. Thermal Response http://onsemi.com 5 NTLJS3113P PACKAGE DIMENSIONS WDFN6 CASE 506AP-01 ISSUE A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.20mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. 5. CENTER TERMINAL LEAD IS OPTIONAL. TERMINAL LEAD IS CONNECTED TO TERMINAL LEAD # 4. 6. PINS 1, 2, 5 AND 6 ARE TIED TO THE FLAG. DIM A A1 A3 b b1 D D2 E E2 e K L L2 J J1 MILLIMETERS MIN MAX 0.70 0.80 0.00 0.05 0.20 REF 0.25 0.35 0.51 0.61 2.00 BSC 1.00 1.20 2.00 BSC 1.10 1.30 0.65 BSC 0.15 REF 0.20 0.30 0.20 0.30 0.27 REF 0.65 REF D A B 2X 0.10 C 2X 0.10 C 0.10 C 7X 0.08 C D2 6X L 1 3 E2 NOTE 5 K BOTTOM VIEW mCool is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. II II A3 A A1 C 4X SEATING PLANE PIN ONE REFERENCE E e L2 b1 6X SOLDERMASK DEFINED MOUNTING FOOTPRINT 2.30 6X 1.10 0.10 C A 0.05 C 6 4 B 6X 0.43 1 1.25 0.35 0.60 0.35 b 6X J J1 0.10 C A 0.05 C B 0.34 0.66 NOTE 3 0.65 PITCH DIMENSIONS: MILLIMETERS http://onsemi.com 6 NTLJS3113P/D |
Price & Availability of NTLJS3113P06 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |