|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ASAHI KASEI [AKD4112B] AKD4112B AK4112B Evaluation Board Rev.A GENERAL DESCRIPTION AKD4112B is the evaluation board for AK4112B, 96kHz digital audio transceiver. This has optical and BNC connector to interface with other digital audio equipment. The AKD4112B is also available to output analog data via on-board DAC, AK4394. n Ordering guide AKD4112B --Evaluation board for AK4112B (A cable for connecting with printer port of IBM-AT compatible PC and a control software are packed with this.) FUNCTION o Digital interface -S/PDIF : 4 channel input ( optical or BNC) 1 channel output ( optical or BNC) - Serial audio data I/F : 1 output ( for DIR data output. 10-pin port) o Analog interface -DAC output : Differential stereo output (Lch/Rch) o 10pin header for serial control interface 3.3V GND Control 5V GND +12V -12V DAC(AK4394) Analog Buffer Opt RX0 AK4112B Serial Data out Fig 1. AKD4112B Block Diagram *Circuit diagram and PCB layout are attached at the end of this manual. 2002/12 ASAHI KASEI [AKD4112B] n Evaluation modes (1) Evaluation for DIR (Digital output) S/PDIF in(optical or BNC) - AK4112B - Serial Data out(10pin port) (2) Evaluation for DIR(analog output via DAC) S/PDIF in(optical or BNC) - AK4112B - DAC(AK4394) - Analog out(Balance XLR) n Operating sequence (1) Set up the power supply lines. [-12V] (Blue) = -12 ~ -15V [+12V] (Orange) = +12 ~ +15V [Analog 5V] (Red) = 5V : Open when the JP15(REG5V) is short. [AGND] (Black) = 0V [Digital 5V] (Red) = 5V [DGND] (Black) = 0V [Analog 3V] (Green) = 3.3V : Open when the JP13(REG3V) is short. [AGND2] (Black) = 0V [Digital 3V] (Green) = 3.3V Each supply line should be distributed from the power supply unit. (2) Set up the evaluation mode and jumper pins. (See p.3.) (3) Connect cables. (4) Power on. The AK4112B and AK4394 should be reset once bringing PDN(SW3) "L" upon power-up. (5) Set up software. Both the serial and parallel mode are available for AK4112B. AK4394 is fixed to serial control mode. In the serial mode, The IBM-AT compatible PC can control both AK4112B and AK4394 by using the printer port and PORT2 on the AKD4112B. Connect PORT2 (uP-I/F) with PC by 10-line flat cable packed with the AKD4112B. 10 PORT2 uP-I/F 9 CSN CCLK CDTI CDTO 2 1 Take care of the direction of connector. There is a mark at pin#1. The pin layout of PORT2 is as Figure 2. n Connection of PORT2 Figure 2. PORT2 pin layout CSN Connect PC CCLK/SCL CDTI/SDA AKD4114 CDTO/ACK 10 wire flat cable 10 pin Connector 10 pin Header 2002/12 ASAHI KASEI [AKD4112B] n Jumper set up. (See the datasheet of AK4112B) No. Jumper Name Function RX0 input circuit set-up. OPT : Optical (default) 1 RX0 BNC : BNC SDA/CDTO pin set-up 2 SDA/CDTO Serial mode : Short both "SDA" and "CDTO/CM0=L". (default) Parallel mode : Select CM0="H" or CM0="L" to set CM0 3 Don't care 5,6,8 RX4-7 Don't care 4 DIT MCLK Don't care MCKO set-up for PORT4(DIR; DAC) MCKO1 : MCKO1 of AK4112B (default) 7 DIR MCLK , MCKO2 : MCKO2 of AK4112B 9 TX0 Don't care Don't care 10 TX1 11 12 BNC 4112B VD Don't care Power supply source set-up for DVDD of AK4112B. D3V : from Digital 3V Jack (default) A3V : from Analog 3V Jack. Power supply source set-up for AVDD of AK4112B. Open : from Analog 3V Jack (default) Short : from the regulator. Do not connect anything the Analog 3V Jack. Power supply source set-up for DVDD of AK4394. D5V : from Digital 5V Jack (default) A5V : from Analog 5V Jack Power supply source set-up for AVDD of AK4394. Open : from Analog 5V Jack (default) Short : from the regulator. Do not connect anything the Analog 5V Jack. Connection of AGND2(AK4112B AVSS) and DGND(AK4112B DVSS) Open : Separate two grounds. Short : Connect two grounds. (default) Connection of AGND(AK4394 AVSS) and DGND(AK4112B DVSS) Open : Separate two grounds. (default) Short : Connect two grounds. 13 REG3V 14 4395_DVDD 15 REG5V 16 AGND2/DGND 17 AGND2/DGND 2002/12 ASAHI KASEI [AKD4112B] n DIP switch(SW1) set-up : -off- means "L" No. Switch Name Function 1 IPS0 Don't care 2 DIF0 DIF0 pin set-up (for parallel mode) 3 DIF1 DIF1 pin set-up (for parallel mode) 4 DIF2 DIF2 pin set-up (for parallel mode) 5 IPS1/IIC Don't care P/SN pin set-up. "H": parallel mode, "L": serial mode. 6 P/SN 7 XTL0 Don't care 8 XTL1 Don't care n DIP switch(SW2) set-up : -off- means "L" No. Switch Name Function 1 CM1 CM1 pin set-up (for parallel mode) 2 OCKS1 OCKS1 pin set-up (for parallel mode) 3 OCKS0 OCKS0 pin set-up (for parallel mode) 4 TEST1 Don't care 5 (reserved) 6 7 8 (reserved) (reserved) (reserved) n Toggle switch set-up 3 PDN Reset switch for AK4112B and AK4394. Set to "H" during operation. Bring to "L" once after the power is supplied. n LED indication 1 INT0 2 INT1 Bright when ERF pin goes to "H". Bright when FS96 pin goes to "H". n Set-up of AK4394 (for the evaluation via DAC. Refer the AK4394 datasheet) In case of evaluating via DAC(AK4394), the AK4394 needs to be controlled by serial control. The default set-up of AK4394 audio format is 16bit right justified, but AK4112B is left justified slave mode. Please adjust those two audio formats. In detail, please refer those datasheets. n Set-up of AK4112B (Refer the AK4394 datasheet) 1. MCKO1/2 output No. 0 1 2 3 OCKS1 0 0 1 1 OCKS0 MCKO1 MCKO2 X'tal 0 256fs 256fs 256fs 1 256fs 128fs 256fs 0 512fs 256fs 512fs 1 Test Mode Table 1. Master Clock Frequency Select fs (kHz) 32, 44.1, 48, 96 32, 44.1, 48, 96 32, 44.1, 48 Default 2002/12 ASAHI KASEI [AKD4112B] 2. Clock operation mode Mode 0 1 2 3 CM1 0 0 1 1 CM0 0 1 0 1 UNLOCK PLL X'tal Clock source SDTO Default ON ON(Note) PLL RX OFF ON X'tal DAUX 0 ON ON PLL RX 1 ON ON X'tal DAUX ON ON X'tal DAUX ON: Oscillation (Power-up), OFF: STOP (Power-down) Table 2. Clock Operation Mode select 3. Audio interface format DIF2 0 0 0 0 1 1 1 1 DIF1 0 0 1 1 0 0 1 1 DIF0 0 1 0 1 0 1 0 1 DAUX 24bit, Left justified 24bit, Left justified 24bit, Left justified 24bit, Left justified 24bit, Left justified 24bit, I2S 24bit, Left justified 24bit, I2S LRCK I/O 16bit, Right justified H/L O 18bit, Right justified H/L O 20bit, Right justified H/L O 24bit, Right justified H/L O 24bit, Left justified H/L O 24bit, I2S L/H O 24bit, Left justified H/L I 24bit, I2S L/H I Table3. Audio Data Format SDTO BICK 64fs 64fs 64fs 64fs 64fs 64fs 64-128fs 64-128fs I/O O O O O O O I I Default 2002/12 ASAHI KASEI [AKD4112B] AKD4112B Control Program operation manual n Set-up of evaluation board and control software 1. Set up the AKD4112B according to previous term. 2. Connect IBM-AT compatible PC with AKD4112B by 10-line type flat cable (packed with AKD4112B). Take care of the direction of 10pin header. (Please install the driver in the floppy-disk when this control software is used on Windows 2000/XP. Please refer "Installation Manual of Control Software Driver by AKM device control software". In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.) 3. Insert the CD-ROM labeled "AK4112B Evaluation Kit" into the CD-ROM drive. 4. Access the CD-ROM drive and double-click the icon of "AKD4112B"to set up the control program. 5. Then please evaluate according to the follows. n Operation flow Keep the following flow. 1. Set up the control program according to explanation above. 2. Click "Port Setup" button. 3. Then set up the dialog and input data. n Explanation of each buttons 1. [Port Setup] : set up the printer port. 2. [Write default] : initialize the register of AK4112B. 3. [All read] : read all registers. 4. [Read] : read data from each register. 5. [Write] : write data to each register. If you want to write the input data to AK4112B, click "OK" button. If not, click "Cancel" button. n Indication of data Input data is indicated on the register map. Red letter indicates "H" or "1" and blue one indicates "L" or "0". Blank is the part that is not defined in the datasheet. End. 2002/12 ASAHI KASEI [AKD4112B] AK4394 Control Program ver 1.0 operation manual 1. Connect IBM-AT compatible PC with AKD4112B by 10-line type flat cable (packed with AKD4112B). Take care of the direction of 10pin header. (Please install the driver in the floppy-disk when this control software is used on Windows 2000/XP. Please refer "Installation Manual of Control Software Driver by AKM device control software". In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.) 2. Insert the CD-ROM labeled "AK4112B Evaluation Kit" into the CD-ROM drive. 3. Access the CD-ROM drive and double-click the icon of "ak4394.exe" to set up the control program. 4. Then follow the displayed comment (See the following). ==================== < RSTN ) 1 RSTN ) 1 2002/12 ASAHI KASEI [AKD4112B] IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. 2002/12 E D C B A U1C 74HCT14 VD 5 R2 VD 8 10k CM1 4Y 12 3Y U1D 74HCT14 P/SN A/B G 74HCT157 R100 D3V JP2 10k R19 SDA/CDTO 100 SDA CDTO/CM0=H CM0=L 1 R9 9 9 R4 2Y 10k R5 7 10k 1Y R3 470 4 C1 C2 C3 0.1u 0.1u 0.1u LE1 VD INT0 LE2 OPT For U1,U2,U3 L1 10u R1 6 1k R7 1k 4 3 2 1 VD C4 PORT1 6 6 GND VCC 5 5 GND OUT TORX176 INT1 470 OCKS0 470 OCKS1 2 3 5 6 11 10 14 13 1 15 0.1u C5 + 10u R6 4 4 470 JP1 RX0 BNC U2 1A 1B 2A 2B 3A 3B 4A 4B J1 BNC A3V C7 10u uP-I/F D3V 10k C9 0.1u TEST1 C11 0.1u 48 47 46 45 44 43 42 41 40 39 38 37 + R13 U3A 2 74LS07 + C6 1 2 3 4 5 CSN SCL/CCLK R10 SDA/CDTI 51 SDA(ACK)/CDTO R11 R14 R8 PORT2 10 9 8 7 6 R12 75 J2 BNC 0.1u C8 100 100 CSN CCLK R15 75 0.1u J3 BNC R16 18k C12 0.47u C10 R17 100 CDTI CDTO R18 75 J4 BNC 0.1u J5 BNC C14 RX5 MCKO1 R20 75 JP4 DIT MCLK MCKO2 JP3 RX4 JP5 RX5 RX3 AVSS RX2 TEST1 RX1 AVSS RX0 AVSS VCOM R AVDD INT1 C13 RX4 R21 75 0.1u DIF0 DIF0 J6 BNC 0.1u IPS0 IPS0 3 R22 75 JP7 DIR MCLK MCKO2 MCLK BICK LRCK DAUX 1 2 3 4 5 R74 10k PORT3 10 9 8 7 6 DIT GND GND NC NC NC 3 J7 BNC C15 JP6 RX6 VD R23 10k RX6 RX7 R24 75 DIF2 DIF2 J8 BNC IPS1/IIC P/SN XTL0 XTL1 VIN 100 100 100 100 TVDD DVSS TX0 TX1 BOUT COUT UOUT VOUT DVDD DVSS MCKO1 LRCK 0.1u DIF1 DIF0 C16 R28 75 JP8 RX7 13 14 15 16 17 18 19 20 21 22 23 24 VD C17 10u + C18 0.1u + D3V C22 5p 2 XTI C23 5p 1 X1 XTO 11.2896MHz R31 R32 100 100 0.1u 1 2 3 4 5 6 7 8 9 10 11 12 IPS0/RX4 AVSS DIF0/RX5 TEST2 DIF1/RX6 AVSS DIF2/RX7 IPS1/IIC P/SN XTL0 XTL1 VIN CSN CCLK CDTI CDTO PDN XTI XTO R25 R26 R27 R29 MCKO1 INT0 OCKS0/CSN OCKS1/CCLK CM1/CDTI CM0/CDTO PDN XTI U4 XTO DAUX AK4114 MCKO2 BICK SDTO 36 35 34 33 32 31 30 29 28 27 26 25 MCLK BICK LRCK SDTO 1 2 3 4 5 PORT4 10 9 8 7 6 DIR GND GND NC NC NC VD R30 10k JP9 TX0 OPT C19 0.1u C20 10u MCLK BICK LRCK SDTO VD 2 PORT5 55 IN VCC IF 6 6 GND TOTX176 4 3 2 1 BNC R33 1k C21 0.1u 2 J9 TX0 T1 DA02-F R34 1:1 BCUV R73 SW1 10k R36 150 VIN 240 1 2 3 4 5 BOUT COUT UOUT VOUT VIN R35 R37 R38 R39 R40 100 100 100 100 100 PORT6 10 9 8 7 6 R41 10k SW2 VD CM1 OCKS1 OCKS0 TEST1 J10 TX1 T2 DA02-F R42 VD VD D1 1S1588 U1A 1 H L U1B 2 3 4 R43 100 SW3 PDN RP2 C24 74HCT14 0.1u 74HCT14 1 PDN 1:1 R44 150 240 PDN XLR VIN RP1 IPS0 DIF0 DIF1 DIF2 IPS1/IIC P/SN XTL0 XTL1 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 1 BNC 3 3 2 2 1 JP11 BNC JP10 TX0 CM1 OCKS1 OCKS0 TEST1 Title (Reserved) Size Document Number J11 XLIN 1 1 2 3 4 5 6 7 8 9 IPS0 DIF0 DIF1 DIF2 IPS1/IIC P/SN XTL0 XTL1 47k D C AKD4114 Rev 1 2 3 4 5 6 7 8 9 A3 47k Date: B AK4114 Sheet Wednesday, December 06, 2000 A A 1 of 2 E 5 4 3 2 1 Digital 3V JP12 L3 1 OUT REG 5V 47u 4114 VD Analog 3V L2 GND IN 2 C38 + 47u 10u 0.1u 10u 0.1u 10u 0.1u 10u 0.1u for NJM5534D x 4 +12V 3 + C37 47u 47u 2 47u 2 D3V A3V VD 4394 A5V JP15 REG 5V T4 NJM78M05FA GND D REG 5V IN C40 0.1u 47u 1 C41 + 10u + L7 + C42 C43 C44 C45 C46 C47 C48 C49 VOP+ JP16 AGND2/DGND 2 AGND/DGND 47u JP17 3 OUT + C39 + + 10u 0.1u 10u 0.1u 10u 0.1u 10u 0.1u AGND2 C50 6800p DGND AGND VOP+ (short) 300 300 7 C51 AOUTL1- R47 NJM5534D R48 3+ 26 R50 4 180 VOP- U5 + R49 (open) VD 6800p C52 C C53 10u 0.1u + C54 R52 750 R51 100 AOUTL(CANNON_M) J12 R53 MCLK LRCK 4394 A5V R60 C59 0.1u 10u CSN 100 AOUTL1+ AOUTL1AOUTR1+ AOUTR1- AOUTL1+ C58 C61 CCLK CDTI + C60 (open) R61 6800p 6800p 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 C55 0.1u U6 DVSS ACKS/DZFR DVDD CKS1/CAD1 MCLK CKS0/DZFL PDN P/S BICK VCOM SDATA AOUTL+ LRCK AOUTLSMUTE/CSN AOUTR+ DFS0/CAD0 AOUTRDEM0/CCLK AVSS DEM1/CDTI AVDD DIF0 VREFH DIF1 VREFL DIF2 BVSS AK4394 C56 + 10u 4 C57 + (short) 300 300 100 100 28 27 26 25 24 23 22 21 20 19 18 17 16 15 R58 R59 2 3 + SDTO R57 100 6 VOP+ C62 6800p B B VOP+ (short) 300 300 7 C63 AOUTR1- R62 + R63 NJM5534D U8 3+ 2R64 (open) 6 C64 6800p R65 4 180 VOP- R66 R67 750 100 AOUTR(CANNON_M) J13 R68 VOP- 100 2 4 U9 + (short) AOUTR1+ 300 300 1 BICK R56 PDN NJM5534D U7 R55 180 1 R54 VOP- 100 2 2 3 3 2 NJM5534D 3 R69 180 3 1 C66 R72 (open) A 6800p 7 C67 6800p 5 4 3 + 3 - C65 R70 R71 2 6 1 VOP+ Title Size Document Number AKD4114 Rev A3 Date: 2 AK4394 Sheet Wednesday, December 06, 2000 1 + + + + + C25 10u 10u 5.1 10u 10u + REG 3V C27 47u D3V A3V 1 + D5V A5V R45 3 C28 3 1 JP13 L4 R46 L5 L6 C29 C30 C31 C32 C33 C34 C35 C36 T3 LP2950A Digital 5V 4395_DVDD Analog 5V -12V JP14 for NJM5534D x 4 VOP- 10u 5.1 C26 + D C A A 2 of 2 5 4 3 2 1 CN3 48pin_3 36 31 30 29 28 27 26 ERF PDN BICK DAUX CM1/CDTI 33 OCKS0/CSN 35 OCKS1/CCLK 34 ERF CM0/CDTO 32 PDN MCKO2 SDTO D 25 D CN2 CN4 LRCK 24 37 MCKO1 23 FS96 FS96 38 DVDD DVSS DVSS TVDD DVDD DVDD DVSS AVDD 22 39 21 C + C 40 C3 0.1u C4 0.1u C1 10u 1 2 + C2 10u 2 1 20 41 AVSS 19 42 RX1 18 X1 C5 5p U1 AUTO 17 43 11.2896MHz 2 V/TX 44 C6 5p 1 16 45 R1 18k PDN V/TX ERF FS96 V/TX 15 46 1 + C7 10u C8 0.1u 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DVDD CM0/CDTO DVSS CM1/CDTI TVDD OCKS1/CCLK V/TX OCKS0/CSN XTI MCKO1 XTO MCKO2 PDN DAUX R BICK AVDD SDTO AVSS LRCK RX1 ERF RX2/DIF0 FS96 RX3/DIF1 P/S RX4/DIF2 AUTO AK4112BVF 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 B 47 B 2 TVDD TVDD 13 48 48pin_2 48pin_4 DIF0/RX2 DIF1/RX3 1 2 3 4 5 6 7 DIF2/RX4 8 9 P/S 10 11 CN1 48pin_1 A 12 A Title AKD4112BVF-SUB Size Document Number Rev A3 Date: 4 3 2 AK4112B Monday, November 27, 2000 Sheet 1 SUB 1 of 1 5 |
Price & Availability of AKD4112B |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |