View NSVA301_994573.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NSVA301 Jan-02
JRC SAW FILTER
NSVA301
Application
959.5MHz CT1
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Input and Output Impedance 50 Nominal Center Frequency (f0) 959.5MHz Insertion Loss 958.3~960.7MHz 3.5dB max. Response Variation 958.3~960.7MHz 1.5dB max. Input and Output VSWR 958.3~960.7MHz 2.5 max. Out of Band Rejection D.C~<879.5MHz 55dB min. (Relative to 879.5~914.5MHz 45dB min. Through Level) 1001.1~1019.5MHz 40dB min. <1019.5~1500MHz 55dB min. (Operating Temperature Range: -10~+60C)
Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature
Rating +20dBm 7.5V -10~+60C -20~+70C
Mechanical Specifications: (Fig.2) Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
Communications Equipment Division Communications Equipment Marketing Department
17-22 Akasaka 2-chome minato-ku, Tokyo. 107-0052 Japan Tel. +81 3-3584-8811 Fax. +81 3-3584-8876 http://www.jrc.co.jp/product/comm/deveice/saw/saw_top.html (Japanese) http://www.jrc.co.jp/product/comm/device/saw/saw_top_e.html (English)
NSVA301 Jan-02
IN 50
1
8
7
OUT 50
2 SAW 6 3 4 5
(a) (1)
Fig.1 Measuring circuit
3.50.2 (b)
3 .5 0 .2
J17
59
(3) (0.95)
(2)
4
(0.8) [5x]
(0 .6 )
5
(0.6)
[8 x ]
3
Marking (1) Manufacture's Mark (2) Lot Number (a) Year (b) Month *Oct.--- X Nov.--- Y Dec.--- Z (3) Part number Mark Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND
1 .0 0 .2 (2 .5 4 )
2
(1 .2 7 )
6
(1 .0) [2 x ]
1 8
7
Fig.2 Package dimensions (in mm)
4.3 0.6 1.2 [6x]
0.6 [6x] 4.3 1.27 1.27
Via -Hole( 0.3)
Fig.3 Desirable land area (in mm)
NSVA301 Jan-02
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -10C or more than +60C, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350C max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.

▲Up To Search▲

Price & Availability of NSVA301

	To Download NSVA301 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .