![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
21cm COLOR TFT-LCD MODULE (8.4 TYPE) LIQUID CRYSTAL DISPLAY DIVISION PRODUCT INFORMATION FEATURES (1) 8.4" SVGA color display with High Brightness (350cd/m 2). (2) Wide viewing angle. (3) Built in Long Life CCFLs (MTTF:50,000 h). ( Conditions / Ta:25*ZI FL:6mA(rms)(continuing lighting), fFL:40kHz ) , (4) Replaceable structure of lamp units. LTM08C351 (p-Si TFT) TENTATIVE MECHANICAL SPECIFICATIONS Item Dimensional Outline (Typ.) Number of Pixels Active Area Pixel Pitch Weight (approximately) Backlight Specifications 199.5(W) x 149.5(H) x 12.0max(D) mm 800 (W) x 600 ( pixels H) 170.4(W) x 127.8 (H) mm 0.213(W) x 0.213 (H) (395)g Twin CCFLs, Side-light type ABSOLUTE MAXIMUM RATINGS Item Supply Voltage (VDD) (VFL) FL Driving Frequency (FL) f Input Signal Voltage ( IN) V Operating Temperature Storage Temperature Storage Humidity (Max. wet bulb temp. = 39C) Min. -0.3 0 -0.3 0 -20 10 Max. 4.0 2.0 100 VDD+0.3 50 60 90 Unit V kV(rms) kHz V C C %(RH) ELECTRICAL SPECIFICATION Item Supply Voltage FL Start Voltage (Ta=0C) High Level Input Voltage Low Level Input Voltage Current Consumption *1*2 Power Consumption *1 : 8 color bars pattern *2 : Excepting the efficiency FL inverter (VDD) (VFL) ( IH) V (V IL) *1 (I DD) *2 (I FL) Min. 3.0 (480) 1400 0.8 VDD 0 --3.0 --- Typ. 3.3 (530) ------(240) --(7.2) Max. 3.6 (580) 1600 VDD 0.2 VDD --6.0 --- Unit V V(rms) V(rms) V V mA mA(rms) W Remarks I FL=6.0 mA(rms) @350cd/m 2 OPTICAL SPECIFICATION (Ta=25C) Item Contrast Ratio ( R) C Response Time Luminance (L) Min. 100 ----(280) Typ. 250 ----(350) Max. --50 50 --Unit --ms ms cd/m 2 Remarks (tON) (tOFF) I FL=6.0mA(rms) *The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba before proceeding with the design of equipment incorporating this product. (1/8) 2000-02-25 (Ver.0.2) LTM08C351 Unit : mm DIMENSIONAL OUTLINE (front figure) Standard tolerance :*}0.5 ( 7. 1) (2/8) 2000-02-25 (Ver.0.2) LTM08C351 BLOCK DIAGRAM ) Y dr i ver 1 - P el an T mn iig C t roll e on r X- dr i v er 1) FP C FP C G ay scal e M pul at i on r ani V t age G ol ener at i on C r cui t i Note1) Build up LCD drivers on the glass substrate 800 pixels 1, 1 1, 2 2, 1 X2 n-1, 1 X2 n, 1 800, 1 1, Y X2n-1, Y X2n, Y 600 pixels 1, 600 800,600 (3/8) 2000-02-25 (Ver.0.2) (1 ) Ve r t ica l T m ing i t1 t2 TIMING CHART NC L K t3 t3 EN A B X , X , X , X ,4 1 2 3 X, 598 X , 599 X ,600 X, Y R5 R0 G5 - 0 G B5 -B0 (2 ) Ho r izon ta l T m ing i t3 t4 t5 (4/8) 797 , Y 1 , 2, 3, 4 , 5 , 6, 7, YYYYYYY X, Y 798 , Y 800 , Y 799 , Y t6 t5 t7 NC L K EN A B R5 R0 G5 - 0 G B5 -B0 V I H= (M I N ) :0 .8V D ( ) DV V I L= (M A X ) :0 .2V D ( ) DV t8 t9 a b NK CL Inpu t S igna l Cen te r Leve l : 0 .5 V D ( ) DV V I H= (M I N ) :0 .8V D ( ) DV V I L= (M A X ) :0 .2V D ( ) DV _ Du ty (a ,b ) :50 + 10% 0 .5 V D ( ) DV LTM08C351 2000-02-25 (Ver.0.2) EA NB R5 - R0 G5 - G0 B5 - B0 LTM08C351 TIMING SPECIFICATION Item Frame Period Vertical Display Term One Line Scanning Time Horizontal Display Term Clock Period Clock "L" Time Clock "H" Time Set Up Time Hold Time Note 1) 1) 2) 3) 4) Symbol t1 t2 t3 Min. 604 x t3 600 x t3 944 x t5 26.3 800 x t5 24.7 9.0 9.0 4.0 5.0 Typ. 628 x t3 16.58 600 x t3 1056 x t5 26.4 800 x t5 25.0 --------- Max. 677 x t3 17.86 600 x t3 1064 x t5 --800 x t5 27.8 --------- Unit --ms ----s --ns ns ns ns ns Remarks 1) 1) 1) t4 t5 t6 t7 t8 t9 1) When ENAB is fixed to "H" level or "L" level after NCLK input, the panel is displayed as black. However, it may be occurred a flicker on the display. Note 2) Note 3) Note 4) When NCLK is fixed to "H" level or "L" level, the panel becomes white stage after several seconds. Do not change t1 and t3 values in the operation. When t1 or t3 is changed, the panel is displayed as black. Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency). Note 5) Keep constant the number of clock within one line scanning time and the number of scanning line within one flame period. Notes 6) Do not hold NCLK on "H" level nor "L" level during VDD(+3.3V) Is supplied. When it holds on, DC voltage supplies to liquid crystal materials and it may cause damage to liquid crystal materials. SEQUENCE OF POWER SUPPLIES AND SIGNALS 10m m ) s( ax. 3. 0V VD D NCL K ENAB DATA 0. 2 V D D 0. 2 V D D 0. 2V 40m m ) s( ax. 0m m n. ) s( i 10m m ) s( ax. 3. 0V 40m m ) s( ax. 0m m n. ) s( i 0. 2V 0. 2V 500m m n. ) s( i (5/8) 2000-02-25 (Ver.0.2) LTM08C351 CONNECTOR PIN ASSIGNMENT FOR INTERFACE CN1 INPUT SIGNAL Connector : DF19G-30P-1H/HIROSE ELECTRIC CO., LTD. Mating Connector : DF19G-30S-1C(housing),DF19-2830SCFA(contact pin)/HIROSE ELECTRIC CO., LTD. Terminal No. Symbol Function 1 GND 2 VDD +3.3V POWER SUPPLY 3 VDD +3.3V POWER SUPPLY 4 GND 5 ENAB COMPOUND SYNCHRONIZATION SIGNAL 6 B5 2) BLUE DISPLAY DATA (MSB) 7 B4 2) BLUE DISPLAY DATA 8 B3 2) BLUE DISPLAY DATA 9 B2 2) BLUE DISPLAY DATA 10 B1 2) BLUE DISPLAY DATA 11 B0 2) BLUE DISPLAY DATA (LSB) 12 GND 13 G5 2) GREEN DISPLAY DATA (MSB) 14 G4 2) GREEN DISPLAY DATA 15 G3 2) GREEN DISPLAY DATA 16 G2 2) GREEN DISPLAY DATA 17 G1 2) GREEN DISPLAY DATA 18 G0 2) GREEN DISPLAY DATA (LSB) 19 GND 20 R5 2) RED DISPLAY DATA (MSB) 21 R4 2) RED DISPLAY DATA 22 R3 2) RED DISPLAY DATA 23 R2 2) RED DISPLAY DATA 24 R1 2) RED DISPLAY DATA 25 R0 2) RED DISPLAY DATA (LSB) 26 GND 27 NC 1) 28 NC 1) 29 NCLK SAMPLING CLOCK 30 GND CN2 CCFL POWER SOURCE Connector : BHR-04VS-1/JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Mating Connector : SM04(4.0)B-BHS-1-TB/JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Terminal No. Symbol Function 1 VFLH CCFL POWER SUPPLY (HIGH VOLTAGE) 2 VFLH CCFL POWER SUPPLY (HIGH VOLTAGE) 3 NC 1) 4 VFLL CCFL POWER SUPPLY (LOW VOLTAGE) Note 1) NC Terminal is open. (Don't use) Note 2) See next page. (6/8) 2000-02-25 (Ver.0.2) LTM08C351 256k (k=1024) COLORS COMBINATION TABLE Basic Color Display Black Blue Green Light Blue Red Purple Yellow White Black Dark Light Red Black Gray Scale of Red R5 L L L L H H H H L L L R4 R3 R2 R1 R0 LLLLL LLLLL LLLLL LLLLL HHHHH HHHHH HHHHH HHHHH LLLLL LLLLH LLLHL : : H H H L L L H H H L L L : : H H H L L L L H H L L L H L H L L L G5 L L H H L L H H L L L G4 G3 G2 G1 G0 LLLLL LLLLL HHHHH HHHHH LLLLL LLLLL HHHHH HHHHH LLLLL LLLLL LLLLL : : L L L L L L L L L L L L : : L L L L L L L L L L L H L L L L H L B5 L H L H L H L H L L L B4 B3 B2 B1 B0 LLLLL HHHHH LLLLL HHHHH LLLLL HHHHH LLLLL HHHHH LLLLL LLLLL LLLLL : : L L L L L L L L L L L L : : L L L L L L L L L L L L L L L L L L Gray Scale Level L0 L1 L2 L3... L60 L61 L62 L63 L0 L1 L2 L3... L60 Gray Scale of Green Dark Light Green Black H H H L L L L L L L L L L L L L L L Red Gray Scale of Blue Dark Light Blue Black L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L L L L L L L L H H H L L L H H H L L L H H H L L L : : H H H L L L L H H L L L H L H L L L L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L H L L L L H L L61 L62 Green L63 L0 L1 L2 L3... L60 L61 L62 Blue L63 L0 L1 L2 L3... L60 L61 L62 White L63 Gray Scale of White & Black Dark Light White L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L H L L L L H L L L L L L L L L L L L L L L L L L L : : L L L L L L L L L L L H L L L L H L H H H L L L H H H L L L H H H L L L : : H H H L L L L H H L L H H L H L H L HH HH HH H H H H H H L H H H L H HH HH HH H H H H H H L H H H L H HH HH HH H H H H H H L H H H L H (7/8) 2000-02-25 (Ver.0.2) LTM08C351 ! FOR SAFETY LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information. 1) SPECIAL PURPOSES A) Toshiba's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic. B) Since Toshiba's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba's published specification limits. C) In addition, since Toshiba Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems. 2) DISASSEMBLING OR MODIFICATION DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba doses not warrant the module, if customer disassembled or modified it. 3) BREAKAGE OF LCD PANEL DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 4) GLASS OF LCD PANEL BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken. 5) ELECTRIC SHOCK DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design. 7) DISPOSAL When dispose LCD module, obey to the applicable environmental regulations. (8/8) 2000-02-25 (Ver.0.2) |
Price & Availability of LTM08C351
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |